查询词典 crater

We make a big blast crater of the fucking middle east for all I care.

我们在TMD中东捅了个大漏子，我只知道这个。

Typical volcanic cone in shape, said the volcanic cone, cone with crater, volcanic crater under the deep crustal magma channel and connected.

典型的火山外形呈圆锥形，称火山锥，锥顶有火山口，火山口下有火山通道与地壳深处岩浆相连。

Scenic areas of geological heritage: the crater forest area, a scenic river of lava, waterfalls and Villa area, Jingpohu area, lava plateau area, a small North Lake area, toad pond scenic volcanic cone; of these particular crater forests, waterfalls Villa, lava River, Jingpohu four most famous scenic spots, is the heart of scenic geological park.

七个地质遗迹景区为：火山口森林景区、熔岩河景区、瀑布山庄景区、镜泊湖景区、熔岩台地景区、小北湖景区、蛤蟆塘火山锥景区；其中尤以火山口森林、瀑布山庄、熔岩河、镜泊湖四个景区最为著名，是地质公园的核心景区。

Stravinsky is the smooth-floored crater partially seen on the right side of the image that overlies the rim of the larger, rougher crater Vyasa in the center and left.

斯特拉文斯基为右边半部分平坦陨石坑，覆盖在更大而崎岖的Vyasa陨石坑边缘。

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

About 50,000 years ago, however, a large meteor created Barringer Meteor Crater in Arizona , USA . Also known simply as Meteor Crater, the resulting impact basin spans over a kilometer.

然而，在50，000年以前，一顆巨大的流星在美國亞利桑那州，造成了貝林傑隕石坑，其直徑約有一公里。

On the top of the mountain, there is a large crater with a small peak with a horse hoof-shaped crater that widens to the northeast.

山顶上有大型火山口，是开口向着北东边的马蹄形的大坑

It is a horse hoof-shaped crater that widens to the northwest. Nestled inside is a round, broad crater.

后古岳、石美、囊冀、佐保美等按西北方向形成马蹄形火山口，里边又形成较大的圆形火山口。

Crater lake is in the crater of a dead volcano of the Cascade range.

火山湖 位于喀斯喀特山脉的死火山口附近。

Crater Lake:a lake of southwest Oregon in a volcanic crater of the Cascade Range.

火山湖：美国俄勒冈州西南部喀斯特山脉一个火山凹湖。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。