查询词典 crank-driven

The necessary condition during dynamic balance structure design of high speed crank press has been pointed out, in order to get rid of unbalance of moving parts, which turns unbalance force trend to minimum.

并指出了在高速曲柄压力机动平衡结构设计中应满足的条件，使不平衡力趋向最小，以消除运动部分的不平衡现象。

The results show that the upsetting deformation law of sintered preform is alike with the compact body,and the crank press is the best equipment of powder forging technology.

结果表明：烧结体的镦粗变形规律与致密体相同。指出了曲柄压力机是粉末锻造工艺的最佳设备。

And then the power of servo motor is calculated according to crank press working load , kinematical characteristic, torque and rotational momentum.

以变速驱动压力机的工作负荷、运动特点、工作总功、力矩和角动量为基础，计算其驱动电动机所需的功率。

After reading the relevant references, the author of this paper has discovered that as one of the most important parts in the crank press, a few optimized designing has been included in this field.

作者查阅了大量相关资料后确发现，对于曲柄压力机的关键部件———组合摩擦离合器制动器的优化设计研究相对较少。

This paper studies the crank press on with magnesium alloy casing of the sheet metal stamping die design phones and technology system, studied blank temperature, mold temperature, lubrication conditions, and other factors of the magnesium alloy casing phone Stamping quality.

本文研究了在曲柄压力机上用镁合金板材冲压手机外壳的模具设计和工艺制度，研究了坯料温度、模具温度、润滑条件等工艺因素对镁合金手机外壳冲压质量的影响。

Be the last written out at large crank press institution design specifications,out major parts chart to.

最后写出详尽曲柄压力机机构设计说明书，绘出主要零件图。

Introduced the development of crank press' movement system aided design software based on AutoCAD platform, expatiated upon a kind of self-learning expert knowledge system's construction and a kind of mechanism of auto-record and design report's auto-output in press design's calculations and checks.

本文介绍了基于AutoCAD平台的曲柄压力机运动系统辅助设计软件的开发，阐述了一个学习型的专家知识系统库的架构和压力机设计计算校核过程中的自动记录及设计报告输出机制。

This article pays more attention to research how to design punching moulds and optimize techniques during punching case shells of mobile telephone with magnesium alloy in the crank machine press.

本文研究了在曲柄压力机上用镁合金板材冲压手机外壳的模具设计和工艺制度，研究了坯料温度，模具温度，润滑条件等工艺因素对镁合金手机外壳冲压质量的影响。

Hybrid input crank type press optimum design servo-motor

混合输入；曲柄压力机；优化设计；伺服电机

Experiments show that, in applying the correct mold structure and appropriate process conditions, when the temperature at 350 ° C billets around Rafah Deep Mold temperature at 350 ° C and about good lubrication circumstances, can be successful in stamping on the crank press to produce magnesium phone alloy shell.

实验表明，在应用正确的模具结构和适当的工艺条件下，当坯料温度在350℃左右，拉深凹模温度在350℃左右和良好润滑情况下，能够成功地在曲柄压力机上冲压生产出镁合金手机外壳。用英文翻译一下哦！！！！！！！！！谢谢！！！！！！！！

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。