查询词典 cracking

By analysis of the cracking products, the effects of the coking-inhibitors on the cracking reaction and the cementite phenomenon of the metal were investigated.

结合燃料裂解产物的分析结果，考察了结焦抑制剂对吸热型碳氢燃料裂解反应历程的影响，以及抑制剂对金属挂片上结焦渗碳现象的缓解作用。

Furhermore, theory of fracture mechanics is used to analyze the relation between fracture toughness and stress intensity factor, the similarity conditions of cracking property is deduced, and the model sizes of induced joint, conformed to the cracking conditions, is calculated.

在此基础上运用断裂力学理论，分析应力强度因子与断裂韧度之间的关系，推导出诱导缝的开裂特性相似条件和满足开裂条件的诱导缝模型尺寸。

The results show that the cracking of the pipe is a kind of stress corrosion cracking.

分析结果表明，高压油管的开裂是应力腐蚀开裂造成的。

By the analysis of stress, crack characteristics, cross section metallography, scanning electrometry microscopy, energy spectrum micro-area as well as material quality of top hair clip pipe of Primary reformer, finds out the reason for top hair clip pipe cracking is stress corrosion cracking, and puts forward defending measures.

通过对一段转化炉上发夹管受力分析、裂纹特征、断面金相、电镜扫描、微区能谱、材质等分析，找出了上发夹管开裂的原因是应力腐蚀断裂，提出防护措施。

First, considering the volume expansion process of corroded bolt, the displacement model of mortar inner surface leaded by bolt corrosion is established after the loss of corrosion production is denoted by a filling factor. Second, based on elastic theory, the mortar cracking process is analyzed after the concept of influence coefficient of surrounding rock is introduced in the course of analyzing, and the degree of cracking course affected by surrounding rock parameter is also analyzed; the finite element method is adopted to verify the results.

考虑锚杆锈蚀体积膨胀过程，以填充系数表示砂浆开裂过程中锚杆锈蚀产物的损失，建立了锚杆锈蚀后砂浆内部位移模型，以弹性力学为基础，引入围岩参数影响系数概念，对锚杆锈蚀导致砂浆保护层开裂过程以及围岩参数对开裂过程的影响程度等进行了分析研究，并采用有限元分析方法对其进行了验证。

Compared with thermal cracking of JP-10, the conversion ratio of the catalytic cracking in the temperature range from 500 to 650 ℃ is evidently enhanced. The predominant products of the catalytic cracking are methane, ethane, ethylene, propane, propylene, benzene and benzenoid hydrocarbons.

在500～650 ℃温度范围内，与热裂解相比，分子筛催化可显著提高裂解转化率，主要产物有甲烷、乙烷、乙烯、丙烷和丙烯，以及苯和苯的同系物等。

This paper, considering the character of stress redistribution after cracking, divides concrete elements into crackable elements and uncrackable elements. On one hand, this cracking model does not need to generate new elements and save computing time, which is similar to the benefits of smeared cracking model.

本文根据混凝土开裂后应力重分布的特点，将混凝土单元划分为可开裂单元与不可开裂单元，在计算上具有分布式裂缝模型不用重新划分单元，节省机时的优点；同时在裂缝绘制方面，又具有分离式裂缝模型形象直观的长处。

With increasing the hydrogen content, HIC appears firstly as ductile cracking by microvoid coalescence, then embrittled cracking by microvoid coalescence and finally by low energy rapid cleavage brittle cracking.

随氢含量的增加，相继表现出微孔聚合式韧性开裂、脆化的微孔聚合式开裂和低能解理式脆性开裂。

The results show that the steel in different solution has better performance of anti-hydrogen induced cracking,there is no cracking inside the steel; micro-cracking on the specimen surface mainly nucleates at pitting corrosion pits and expands along the polygonal ferrite; the expansion mode is mostly transgranular type, and the expansion terminates in acicular ferrite.

研究结果表明：该管线钢在两种溶液中均具有较好的抗氢致开裂性能，试样内部没有发现裂纹；试样表面的微裂纹主要在点蚀坑处形核并沿多边形铁素体扩展，扩展模式多为穿晶型，并终止于针状铁素体。

With 54# half-refined paraffin as raw material,the technology of the second injecting steam of ethane cracking is used for reference in the paraffin cracking process which avoides the coke produced in cracking furnace.

采用优质的54#半精炼石蜡，将乙烯裂解二次注汽技术融合在石蜡裂解技术中，避免了裂解炉结焦；考察了单程裂解、炉前甩残蜡循环裂解、炉后甩残蜡循环裂解在相同的工艺条件下的产品质量、产品收率及存在的问题；验证了新的炉后甩残蜡循环裂解是较好的工艺路线，在较高的水蜡比15%，高温600℃、低烃分压和短停留时间(2s左右)条件下，能生产出高质量的α-烯烃产品(总烯烃质量分数在97%以上，α-烯烃含量为88%)。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。