查询词典 cooling

At present, many foreign countries use low-level mold casting, its aim is to improve the cooling intensity, to reduce or eliminate a cooling air gap zone heating phenomenon, it is virtually non-existent secondary cooling of the quenched situation, ordinary flat ingot casting has been the crystallization of height reduced to 100 people, of course, this has required the operator to operate a high level or additional level of white dynamic control system.

目前，许多外国国家使用低级别的模铸造，其目的是提高冷却强度，以减少或消除地区差距的冷却空气加热的现象，几乎是不存在的二次冷却淬火的情况，一般小锭铸造一直减少到100人，当然，高度结晶，这需要经营者经营的高层次或白色的动态控制系统的额外的水平。

Changes of the level of thermal environment reduce cooling load effectively in case of the all-air cooling system while the radiation-panel system does not reduce cooling load even though the targeted thermal condition is relaxed.

在热环境水平发生变化时，采用全空气制冷系统可有效降低制冷负荷；而采用辐射板制冷系统时，即使目标热环境已经放宽，也不能降低制冷负荷。

The result shows that the cooling capacity increases with increasing generator heat transfer. The coefficient of performance of the system increases when the quantity of the generator heat transfer is increased from 6 kW to 7 kW, however it decreases in the range of 7 kW-9 kW. When the fan frequency increases, the temperature of liquid ammonia leaving condenser decreases, while the cooling capacity and the COP of the system increases. When the flow rate and inlet temperature of water/glycol increases, the evaporator takes more heat away and the cooling capacity and COP of the system increases.

其结果可发现当发生器加热量增加，系统温度增加系统冷冻能力增加，但其COP於6 kW-7 kW 系统COP会有先增加，於7 kW-9 kW，系统COP会有下掉的趋势；在冷凝器方面，当风扇频率增加，冷凝器温度降低时，冷凝器出口冷媒随之降低，系统冷冻能力会有所提高，COP亦增加；在蒸发器方面，蒸发器卤水出口温度及卤水流量增加，可以使蒸发器带走更多的热量其系统冷冻能力及COP也就会相对增加。

Bell-type furnace from a shrouds,two furnace Block,two in the hood,a componet cooling enclosures,shrouds-rolled steel used welding of molding,using energy-saving lining all the latest technology fiber module structure,for the Top All Permian High-pressure wave fiber Banding hanging flattened,high aluminum screw linked with resistance bands Top fast-cooling cooling installation Double doors.

罩式炉由一台加热罩、两台炉座、两台内罩、一台冷却罩组成，加热罩采用钢板卷制密焊成型，炉衬采用节能型最新技术全纤维模块结构，炉顶为全纤维波浪叠法高压捆扎吊平顶，高铝螺钉挂装电阻带，炉顶安装双孔快冷降温门。

If the applied power is due to a initial use not the temporary power failure, the cooling temperature is set to the middle value in the cooling temperature range, and then controls loads such as a compressor and a blowing fan in the refrigerator to the driven so that the inside of the refrigerator is cooled according to the set cooling temperature.

如果是缘于首次使用而非暂时电源故障，就把冷却温度设定冷却温度范围的中间值，然后控制电冰箱的压缩机、风扇等负载，使其运转，以便冷却冰箱内部。因而，能把电冰箱的冷却温度设定到接近用户先前设定的温度控制状态。

The preparative technique of solid lubricant is cold-press sintering method.The micro-structure , friction surface, lubricant transfer film surface of base material was characterized by SEM; XRD was used to do phase analysis. The degrees of crystallinity of pure PTFE under the different conditions of water cooling, air cooling and furnace-varying cooling were made comparison by XRD. The thermal stability of pure PTFE and solid lubricant was analyzed by DSC-TG; The composition and valence state of elements in the surface of carbon fiber ,solid lubricant before and after friction test and lubricant transfer film were characterized by XPS; The frictional property of solid lubricant was tested by pin and disk test rig .

用SEM表征原料微观结构、摩擦表面及润滑转移膜表面形貌：用XRD进行原料物相分析，及比较水冷却、空气冷却、随炉冷却三种工艺条件下的纯聚四氟乙烯树脂的结晶度；用DSC-TG分析纯聚四氟乙烯树脂及固体润滑剂的热稳定性；用XPS表征碳纤维表面、固体润滑剂摩擦前后表面、润滑转移膜表面的元素组成、价态变化；用销盘式摩擦磨损试验机对固体润滑剂进行摩擦性能测试；采用专用的台架模拟试验机对固体润滑剂镶嵌轴承套与钢轴摩擦副间的摩擦磨损性能进行测定；用莱次偏光显微镜测试固体润滑剂的硬度；用材料试验机测试固体润滑剂的抗压强度等。

The total static loads and dynamic loads are summed as 4.692W and 38.4W, respectively. And comparison between the double-wall cooling method and the cooling tube method for the 77 heat shield has been discussed to provide the thermal parameters for flow process simulation. The critical thermal parameters of the main components of the QWR cooling system were determined for parallel arranged QWR cryostats. The mass flow and time for cool-down of the QWR to 4.2K was also estimated.

本文在详细描述恒温柜冷却系统的基础上，详细计算了4.2K冷质量与77K冷屏的辐射漏热，同时，还对恒温柜内部支撑系统计算了变物性下的导热漏热，得出了恒温柜系统的静态和动态热负荷分别为4.692W和38.4W，并分析比较了液氮冷屏采用夹层冷却方式与铜管缠绕冷却方式的优缺点，为流程模拟的参数确定提供了依据。

Main contents of the thesis are as follows: Description of the present usage of liquid cooling system, presentation of a new type of liquid cooling system and description of its work principles; Design of the liquid cooling system, which mainly deals with the design and collating calculating of serpentine condenser and heat exchangers adopted in this system. Meanwhile, the model chosen calculating of compressor、thermal expansion valve、plate evaporator、water pump and the like equipment used in the system are also carried out.

本文的主要内容如下：对液冷源使用现状进行了描述，提出了一种新型液冷源系统并对其工作原理进行了阐述；对系统进行了设计，主要对系统中所采用的管带式冷凝器和水侧空/液换热器进行了设计和校核计算，同时对系统中所用到的压缩机、热力膨胀阀、板式蒸发器、水泵等配套设备进行了选型计算；分别对制冷系统和冷却液循环系统进行了数学建模。

Rated at extraction conditions, one pump is running, because the cycle of water to reduce the system's water resistance decrease the flow of water pumps 12274T / H, head will drop to 15.0-16.0 m, in the extraction steam turbine at the maximum operating conditions, the recycled water to meet the system requirements to run a pump, because of substantial reduction in the volume of water supplied, so that substantially improve pump head, a direct result of the cooling tower water gushing, increase淋水device with a flow rate of the sink, fill up water in the hot淋水exchange reduce the time and reduces the cooling effect of cooling towers.

在额定抽汽工况下，一台水泵运行，由于循环水量减少、系统的水阻下降，水泵的流量12274T/H，扬程将下降至15.0-16.0米，在汽轮机在最大抽汽工况时，为满足循环水系统要求运行一台水泵，由于供水量大幅度减少，使水泵扬程大幅度提高，直接造成冷却塔涌水，加大淋水装置配水槽的流速，水流在淋水填料上热交换的时间减少，降低了冷却塔的冷却效果。

Sewage FRP cooling tower rotation atomized spray cooling tower, roof fan, axial fans, centrifugal fan, ventilation pipe and products based on user selection of the cooling tower, the transformation of the user Laota the ideal product.

污水玻璃钢冷却塔喷射旋转雾化冷却塔，屋顶风机，轴流风机，离心风机，通风管道系列产品并可根据用户对冷却塔的选型，老塔的改造得到用户的理想产品。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48