查询词典 cooling

They are generally two different types of cooling system: water-cooling and air-cooling system.Water-cooling syetem is more common.

它们一般是两种不同类型的冷却系统：水冷和风冷system.water冷却syetem更为常见。

A Place the Jacket Cooling Fresh Water system into the warming up state by operating the cooling fresh water exchange valve of the generator engine or by forcing the steam and the cooling fresh water to flow through the Jacket Cooling Fresh Water heater of the Main Engine.

将辅机冷却淡水引入主机缸套水冷却系统加热主机，或将蒸汽引入主机冷却水加热器中。

Place the Jacket Cooling Fresh Water system into the warming up state by operating the cooling fresh water exchange valve of the generator engine or by forcing the steam and the cooling fresh water to flow through the Jacket Cooling Fresh Water heater of the Main Engine.

将辅机冷却淡水引入主机缸套水冷却系统加热主机，或将蒸汽引入主机冷却水加热器中。

C or less of saturated compressed air into the dryer of the pre-cooling device, in the pre-cooling device in heat exchange with the ambient air, high temperature air pre-cooling fan part of the heat is taken away, after pre-cooling the compressed air into the to the pre-evaporator refrigeration system with secondary refrigerant vapor heat exchange, allowing the temperature dropped close to the refrigerant evaporation temperature, and flows through the pre-filter to remove large amount of liquid water, oil mist and dust.

小于等于80°C的饱和压缩空气进入干燥机的预冷器，在预冷器中与环境空气进行热交换，高温压缩空气的一部分热量被预冷风机带走，预冷后的压缩空气进入到制冷系统的前置蒸发器，与冷媒蒸气进行二次热交换，使本身温度降到接近于冷媒的蒸发温度，并流经前置过滤器除去大量的液态水，油雾和尘埃。

As the chamber pressure increases, the only cooling methods that can satisfy the requirements are regenerative cooling only or regenerative cooling combined with film cooling.

作为商会的压力增加，只有冷却方法能够满足要求，再生冷却的唯一或再生冷却结合膜冷却。

There are generally two kinds of cooling systems: water cooling system and air cooling system.

一般有两种冷却系统：水冷系统和空气冷却系统。

Uses two types of automobile engine cooling method, that is, air cooling and water cooling.

汽车发动机采用两种冷却方式，即空气冷却和水冷却。

Through simulation in computer using the all-purpose computer simulation software secondary cooling in slab continuous casting and test results, the influence of the factor such as casting speed, casting temperature, shell thickness and secondary cooling system are analyzed. The secondary cooling system is evaluated, the reasons of crack are analyzed. And the solution scheme is obtained. Strand temperature is measured on site in Basteel.

应用仿真软件和实验数据对宝钢1930铸机进行了仿真计算，分析了拉速、配水制度、过热度对铸坯温度场和坯壳厚度的影响；对宝钢1930铸机的二冷制度进行了评估，分析了产生裂纹的原因；并对二冷制度进行优化，提出了改进建议。

The measuring unit includes one heat block, one cooling block, and one sleeve. The facing end of the heat block and cooling block has one loaded plane which forms one loaded cavity with the sleeve in which the heat block and cooling block can be relative move.

所述量测部包括一加热块、一冷却块及一套筒，所述加热块及冷却块相面对的一端分别具有一承载平面，所述承载平面与所述套筒构成一承载腔，且所述加热块与冷却块可于所述套筒内相对移动。

Under function of fuel pump, one way enters into nozzle burning; another way enters into cooling cavity. Because carbinol vaporize hidden heat is big, and absorbs a great amount of heat in cooling cavity, and nozzle surfaced temperature rapidity drop to below 30EDG C, thereby aim of cooling nozzle is reached.

燃料在泵的作用下一路进入喷嘴进行燃烧；另一路进入冷却腔，由于甲醇的汽化潜热很大，在冷却腔内吸收大量的热量，使喷嘴表面的温度迅速下降到30℃以下，从而达到冷却喷嘴的目的。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48