查询词典 cooling

The mathematical model of the ratio of radiuses difference to electro-negativity difference and the critical cooling rate Rc was established. The same relationships with a shape of upturned parabola in all five kinds of alloys were obtained with this model.

建立了原子半径差与电负性差之比Δd/Δe与临界冷却速度R的数值模型，并在所有五种不同合金系中获得一致且开口向上的抛物线关系。

The cooling performance of both types of radiators was analyzed and the results were acquired.

随着机车向高速大功率方向的发展，冷却技术的改进显得非常重要。

There arethree passive radiators , one of which can be connected to the water cooling system .

有三个被动散热器，其中可连接到冷却水系统。

Let us recall, the standard cooling of such motherboardprovides for the use of radiators and thermal tubes.

让我们回顾一下，标准的冷却，例如主机板规定使用散热器和热管。

The first cooling system version implies the use of two radiators.

第一冷却系统的版本意味着使用两个散热器。

And adopting advanced cooling control process, tubular pile steel wire s with good surface quality,high precision and excellent comprehensive mechanic property is produced.

介绍了天津钢铁公司通过设计合理的化学成分和工艺路线，控制C、Si、Mn等成分均匀稳定，采用先进的控冷工艺，开发出具有表面质量优良、尺寸精度高以及良好的综合力学性能的管桩钢丝用盘条。

Through profited from the overseas equipment the advanced experience, Xiong Wei locks finally the goal in "active cooling" on the system, but this system only equipped the use in the US military Armored force and on the F1 motor racing boats pilot body, only could look up the correlation technique parameter, the home does not have the material object to be possible to use for reference.

通过借鉴国外装备的先进经验，熊伟将目标最终锁定在了&有源冷却&系统上，但该系统仅在美军装甲部队和F1摩托赛艇驾驶员身上装备使用，只能查到相关技术参数，国内没有实物可以借鉴。

Cylinder wall and piston are lubricated by the engine oil sprayed out of the engine oil cooling spraying hook located on auxiliary oil passage of cylinder block; piston pin is lubricated by the lubricant collected in the hole drilled on top of connecting rod small end.

气缸壁和活塞通过位于气缸体副油道上的机油冷却喷钩喷油润滑，活塞销由连杆小头顶部钻孔集油润滑。

The pinch point temperature differences analysis method was introduced in this paper, the major equipments of system was designed in term of the guide line that the best general efficiency of cooling and heating mode should be achieved.

本文首先按照使制冷制热两种典型工况下综合效率最佳的原则，利用挟点温差分析的方法设计了系统的主要部件。

A multi-function heat pipe type adsorption ice maker, which uses activated carbon-CaCl2 as compound adsorbent and ammonia as refrigerant, was designed.For this test unit, the heating, cooling and heat recovery processes between two adsorbent beds were performed by multi-function heat pipes.

设计了一种基于多功能热管的高效吸附式制冰机组，采用氯化钙/活性炭复合吸附剂和氨作为吸附工质对。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48