查询词典 cooling zone

The cooling unit vR-Zone extreme memory chiller is intended for cooling the memory to very low temperature.

冷却股轮带极端记忆式制冷机是为冷却的记忆，以非常低的温度。

The instability originated in the upper R_B-like convection zone develops to larger region with the increase of Grashof number, and the number of non-axi-symmetric circulations decreases. When Grashof number exceeds another critical value, cooling air may invade the cavity and flow toward the shroud, the circulations decrease to one pair occupying the whole cavity in radial, thus these two zones are merged into one. The core structures in the cavity rotate against the disks, while the structures keep no change at the case of periodic oscillatory flow. With the Grashof number rises, the flow undergoes stable, periodic, periodic with cool air invading, quasi-periodic and ultimately to chaos.

离心浮升力是造成非等温轴向通流旋转盘腔内流动不稳定的主要因素，而哥氏力的存在加剧了流动不稳定性，导致流场失稳提前发生，而且在哥氏力的作用下流线发生偏转，盘腔内r-θ面出现了旋向相反的对涡，流动结构更加复杂化；随离心浮升力的继续增加，r-θ面的对涡减少，当其超过某一临界值后部分冷流体侵入盘腔，对涡减少至一对，而且沿径向充满整个盘腔；此后随离心浮升力的增加对涡的数量不再变化；r-θ面的对涡相对于盘面周向移动，但是形状基本保持不变。

The comparatively short cooling line consists of 7 groups of laminar cooling and one zone for trimming.

这个相对较短的冷却线包括了7组层级冷却以及一个微调区域。

Mechanisms of heat affected zone liquation and liquation cracking in GH150 alloy were investigated by using varestraint test and hot ductility test in conjunction with the differential thermal analysis and optical, scanning electron microsopy. On heating,γ/C liquation take places in the HAZ above 1250℃. When the temperature reaches 1353- 1375℃, a large amount of liquid particles due to initial melting can be observed within the grains near the fusion boundary. On cooling,γ/C eutectic and γ/ Laves phase eutectic take place at 1273 and 1200℃ respectively.

采用可变拘束试验、热塑性试验、差热分析、光镜与扫描电镜观察，研究了GH150合金焊接热影响区液化及液化裂纹形成机制加热过程中温度高于1250℃的热影响区由于γ／C共晶产生液化，在温度达到1353℃（固相约至1375℃的近维区，晶内出现大量液化点冷却过程中温度在1273和1200℃时形成γ／C共晶和γ／Laves相共晶。

Effect of cooling speed,stirring speed,seeds on metastable zone has been reviewed.

考察了降温速率、搅拌速率、晶种对介稳区的影响。

However, in spite of different kind of cooling way, the diffusion length of minority carrier in the D-defect zone was always lower than that in the A-defect zone.

这些结果表明，空位促进了铜沉淀的形核，抑制了铜沉淀团的长大。

This study is focusing what the variation of cooling coils pipe pitch and deposit direction, which will affect the temperature distribution of the epitaxy produce zone for rotation dick type of MOCVD system, the cooling coils is at the bottom of the reaction chamber. In other, we also consider what the different if they has exhaust device at reaction chamber too.

本研究主要是对转盘式有机金属化学气相磊晶系统反应腔底部冷却管排之管排间距或摆置方位等之变化，对磊晶工件区之温度分布影响；同时，也对冷却管排底下空间中亦做若有抽气时之温度分布差异分析。

It is revealed that both the roasting and cooling air flow run radially at inlets and then run slantingly upwards or downwards into roasting-preheating zone inside IVAC. And the gas flow in the whole soaking zone is weakened. There are possibly three gas flow patterns in PSF, which are mainly dependent on the ratio of inflow, i.e., the greater the ratio is, the higher the downward roasting air flowrate and the lower the upward air flowrate will be. The critical ratio of inflow mainly depends on the constructional parameters and packed bed conditions of PSF.

结果表明：焙烧风和冷却风在进口处呈放射状，之后斜向上或斜向下分别流入焙烧-预热带和导风墙内；整个均热带内气流较为薄弱；炉内存在三种气流分流的可能，流入风量比是决定气流分流的最主要因素，其中，流入风量比增加，焙烧风下行趋势增大，而冷却风上行趋势减小；临界流入风量比主要取决于结构参数和料层情况。

Therefore liquid CO_2 avoids gas-solid multiphase flow, and supplies continuous low temperature gas for cryoprobe. Experimental results show that the 2-dimension temperature distribution for the first time, it includes:(1) The cooling velocity and freezing zone increases along the flux up at certain size of the cryoprobe in the same biological tissue.(2) As the diameter of cryoprobe increases, the temperature will descend faster, freezing zone will be broader obviously, and ice ball become larger. Until it arrives heat balance, the temperature keeps invariability.(3) Single freezing-thaw results in biggish mechanical injury already for loosen tissue such as pork liver; Successive freeze-thaw circle could quicken freezing and thaw velocity for compact tissue, and it has proved the more mechanical injury of successive freeze-thaw circle than the single freezing-thaw treatment.

文中首次对生物组织进行了二维温度场分布实验研究，得出：(1)当刀头大小一定，对同一组织冷冻时，流量越大，降温速度越快，降温影响区域越大；(2)随着冷刀直径的增加，降温速度随着增加；温度影响区域明显增大；冰球直径也随着增大，热量平衡后温度几乎不随时间变化；(3)对于结构疏松组织比如猪肺脏，单次冻融对组织已造成较大的机械破损；对于结构较致密组织，多次反复冻融可以使降温和复温速率增加，单次冻融的热应力造成的机械破损较小，多次冻融后造成的机械破损比单次冻融所造成的机械破损大；(4)直喷式刀头比导热式节能约15％。

It is considered that pre-tension stress counteract the compression stress in welding zone generated by thermal expansion, consequently reduce the compression plastic deformation, and depress the tension stress in welding zone when cooling down, and accordingly minish the compression stresses far from the welding zone.

分析认为，预拉伸应力部分抵消了焊接区热膨胀产生的压缩应力，从而减小了压缩塑性变形，进而减小了冷却时焊接区域的拉伸应力水平，相应地远离焊缝区域的压缩应力也随之减小。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。