查询词典 cooling effect

Utilizing this simulated program, it analyzes that R11 and cooling water affect to the diathermanous performance of condenser, discusses the condenser structure depending on the working-fluid, cooling water, temperature, velocity of flow.

探讨了冷凝器结构尺寸随着工质和冷却水压力、温度、流速之间的变化关系。

Based on analyzing the dilatometric curves, metallographic structures of test samples of these simulation procedures, four factors which have influences on the tendency of the appearance of the cold cracks in HAZ have been studied, these factors are preheating, slow cooling, expanding the cooling time (t8/5 and t8/3), and heat preservation.

通过对这些模拟过程的热膨胀曲线、试样金相组织等的分析，研究了焊前预热、焊后缓冷、延长冷却时间t8/5与t8/3、焊后保温这四种因素对焊接热影响区冷裂纹产生倾向的影响。

By the method of dilatometric change,combining with microscopic test and hardness measurement,different expanding curves of continuous cooling transformation were measured at different cooling rate,and CCT diagram was obtained by using DIL805A thermal expansion fast phase transition instrument.

利用膨胀法，结合金相法和硬度法，在DIL805A热膨胀快速相变仪上测定了该钢在不同冷速下连续冷却时的热膨胀曲线，获得了该钢的连续冷却转变曲线；研究了该钢连续冷却过程中奥氏体转变过程与组织变化。

The transformation of C-Si-Mn TRIP steel during continuous cooling in two static conditions was studied by dilatometry. The effects of cooling rate and austenitizing process on the microstructure were analyzed.

利用热膨胀法研究了C-Si-Mn系TRIP钢在两种静态条件下连续冷却转变时的相变规律，分析了冷却速度、奥氏体化工艺对组织的影响。

The paper analyses the cooling process of symmetrical and dissymmetrical section profile with FEM software ANSYS, then adopt the data to guide the design of moulds cooling system.

使用有限元分析软件ANSYS分析了对称截面和不对称截面两种型材在定型模内冷却的过程，并采用分析得出的数据指导定型模冷却系统的设计。

ABSTRACT Vacuum cooling is a rapid evaporative cooling technique, which is widely used in food industry.

真空冷却是一种快速蒸发冷却技术，近年来广泛应用于食品工业。

OBJECTIVE: To evaluate and compare the protective effects of sub-hypothermia on brain by extravascular cooling and surface cooling to rabbits after cardiopulmonary resuscitation.

目的：评估和比较体外血液冷却和体表降温形成亚低温对兔心肺复苏后的脑保护作用。

Although this lowest cooling temperature is higher than that achieved by using a double-inlet valve, the cooling power obtained by the refrigerator with an inertance tube is higher than with a double-inlet valve, which demonstrates the excellence of inertance tube.

虽然最低制冷温度高于双向进气型脉管制冷机的制冷温度，但是当制冷温度在75K以上时，惯性管型脉管制冷机的制冷量大于双向进气型脉管制冷机的制冷量，从而体现了惯性管的优越性。

The results show that with the finishing temperature at 950 ℃, as the cooling rate increases, interlamellar spacings of pearlite is reduced; as cooling rate reaches 5℃/s, martensite precipitates.

结果表明，随着冷却速度的加快，高碳钢SWRH77B在950℃变形时，其珠光体的片层间距变细；冷却速度达到5℃/s时，有马氏体组织析出。

Our equipment is equipped with a water cooling system and automatic segmentation system and letoff system for choosing to use the polymer-coated with hot melt Adhesive curing time is 10-38, 15s, left, or, in a production environment normothermic cooled down the time required for this to be greater than standard time, especially in the Division of semi-finished products is cascade linescut, between the temperature so that it is difficult to give off the accumulation of natural cooling curing

我们的设备装有水冷系统和自动分割系统以及收卷系统供选择使用）覆膜用热熔胶的固化时间为10～15s左右、在生产环境常温下自然冷却所需的时间，要大于这个标准时间，特别是半成品在分割前是层叠卷绕的话。相互间温度积聚难以散发，使自然冷却固化

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48