查询词典 cooling duct

27SiMn steel ; continuous cooling transformation curve ; cooling rate ; microstructure ; hardness

27SiMn钢；连续冷却转变曲线；冷却速度；组织；硬度

The continuous cooling transformation curve was constructed chiefly by means of dilatometry,and combined with metallography to exact fix on the phase transition points of different cooling rate.

连续冷却转变曲线的建立主要应用膨胀法，并辅助以金相分析法来精确分析不同工艺条件下的相变点。

The purpose of this paper is to find the proper character of cooling water and the ways of it pass in and out the jet, which make sure that the anode of plasma ignition jet will not be ruined, to prolong the useful life of the pole, by using the numerical analyze in plasma ignition torch against heat transfer of anode and cooling-water against convection current heat transfer, and process the simulation calculation by using FLUENT soft.

本文通过对等离子体点火炬与阳极传热以及冷却水与对流湍流传热的数值分析，运用FLUENT软件进行模拟计算，找出满足使等离子点火器阳极不被烧蚀的冷却水的合理参数及冷却水进出水方式，来延长电极的使用寿命。

Based on the theory of heat and mass transfer for film type cooling, a mathematical model for the velocity distribution of a thin water film, the equations of mass and heat transfer, and evaporation cooling controlled by the latent heat transfer were established.

基于膜状冷却热、质传递机理，建立水膜薄层的速度分布，热、质传递方程和潜热蒸发冷却控制的数学模型。

It was found that partition of cooling process according to the measured cooling rate curve is not totally corresponding to what were visually observed.

对比发现，按测得的冷却特性曲线的形状划分的冷却阶段，与探棒表面实际发生的冷却情况大不相同。

The surface temperature distribution,the spraying cooling curve,and the heat transfer coefficient of spray cooling were obtained.

得到了加热表面温度分布、喷雾冷却曲线和喷雾冷却的换热系数等传热特性。

Results show that the actual location of the cooling curve of the steel can be adjusted by regulating the strength of the steel and the yield strength ratio of the steel can be adjusted by controlling the cooling rate o...

分析认为调节钢的实际冷却曲线位置可调节钢的强度，调节钢在铁素体相变区内的冷却速率来调节钢的屈强比。据此对控冷工艺进行优化，使产品力学性能和组织符合技术要求和用户的要求。

By the cooling curve and the temperature field, it can he known that, the solidification time of ribbon is 1.0×10^(-4)s, the even solidification rate of ribbon with 60 μm thickness is about 10^6K/s, and the temperature of cooling process does not obviously go back by the release of solidification latent heat. The solidification rate of ribbon is at 0.010-0.394 m/s, and it changes from high to low with the prolonged solidification time.

由冷却曲线和温度场曲线类比结果可知，带子的凝固时间为1.0×10^(-4)s；单辊快淬的平均冷却速度在10^6 K/s数量级，且凝固潜热的释放不会明显地引起冷却过程的温度回升；带子的凝固速度在0.010~0.394 m/s范围之内随凝固时间的延长逐渐由大变小。

According to the law of conservation of sample energy during solidification, under the condition of Newton's cooling, the ordinary mathematical equation of cooling curve was analized, and a theoretical method calculating solid phase fractions and latent heat was put forward on the basis of characteristic α value.

在对碳含量、硅含量和碳当量作三维空间投影分析的基础上，根据实验数据回归出了计算铁水碳含量、硅含量、碳当量、磷含量、抗拉强度、硬度和共晶度的数学模型；为了提高对硅含量的测量精度，提出了分段定硅的技术方法。

Combine the cooling characteristic curve of quench media and the dynamics curve of continuum cooling phase change to select the quench media of materials is very useful, and it can obtain best microstructures and controlled crack polarity or distortion.

文章摘要：提出将淬火介质冷却特性曲线与材料的奥氏体连续冷却转变动力学曲线相结合，来选择材料的淬火介质，获得合适的显微组织并控制材料淬火过程中的变形、开裂倾向。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48