查询词典 cooling cycle

In some conventional fan revolution speed control methods, variable control of the number of revolutions of a cooling fan is performed by a process comprising steps of detecting an actual temperature of cooling target fluid, ie fluid to be cooled by the cooling fan, such as hydraulic oil and circulating radiator cooling water for cooling an engine (such cooling water is hereinafter referred to as coolant), determining a target fan revolution speed by a system of a proportional integral control unit based on the difference between the actual temperature detected and a target temperature, and changing the fan revolution speed based on the target fan revolution speed so as to bring the actual temperature of the cooling target fluid down to the target temperature.

在一些传统风扇转速控制方法，控制变量的数目革命的一个冷却风扇，是由一个过程组成的步骤检测到一个实际温度冷却目标流体，即流体被冷却，由冷却风扇，如液压石油和散热器循环冷却水用于冷却发动机（如冷却水是以下简称为制冷剂），确定一个目标风扇转速由一个系统的比例积分控制单元基础上的差异，实际温度检测和目标温度，并改变风扇转速的基础上，针对风扇转速，使实际温度的冷却液指标下降到目标温度。

The effects and mechanism of GABAergic neurons, NOergic neurons, opioid peptide and cyclic adenosine monophosphate in the nucleus reticularis thalami on sleep-wakefulness cycle of rats and the effects and mechanism of the 5-HTergic nerve fibers project from the nucleus raphes dorsalis to RT on sleep-wakefulness cycle of rats were investigated with the methods of brain stereotaxic, nucleus spile, microinjection and polysomngraphy.1. The effects of GABAergic neurons in RT on sleep-wakefulness cycle of rats1.1 Microinjection of 3-mercaptopropionic acid (3-MP, a kind of glutamate decarboxylase inhibitor) into RT. On the day of microinjection, sleep only decreased a litter. On the second day, sleep marked decreased and wakefulness marked increased. On the third and fourth day, sleep and wakefulness stages resumed to normal.1.2 Microinjection of gamma-amino butyric acid (GABA 1.0μg) into RT enhanced sleep and reduced wakefulness compared with control; while microinjection of L-glutamate (L-Glu, 0.2μg) decreased sleep and increased wakefulness; microinjection of bicuculline (BIC, 1.0μg), a GABAA receptor antagonist, enhanced wakefulness and reduced sleep; microinjection of baclofen (BAC, 1.0μg), GABAB receptor agonist, had the same effects as GABA.2. The effects of NOergic neurons in RT on sleep-wakefulness cycle of rats2.1 Microinjection of L-arginine (L-Arg, 0.5μg) into RT decreased sleep compared with control, but there were on statistaical difference between L-Arg group and control; while microinjection of sodium nitroprusside (SNP, 0.2μg), a NO donor into RT, sleep marked decreased and wakefulness marked increased. Microinjection of nitric oxide synthase inhibitor, N-nitro-L-arginine (L-NNA, 2.0μg) into RT enhanced sleep and reduced wakefulness.2.2 After simultaneous microinjection of L-NNA (2.0μg) and SNP (0.2μg) into RT, SNP abolished the sleep-promoting effect of L-NNA compared with L-NNA group; after simultaneous microinjection of L-NNA (2.0μg) and L-Arg(0.5μg) into RT, we found that L-NNA could not blocked the wakefulness-promoting effect of L-Arg.3. The effects of opioid peptide in RT on sleep-wakefulness cycle of rats3.1 Microinjection of morphine sulfate (MOR, 1.0μg) into RT increased wakefulness and decreased sleep compared with control; while microinjection of naloxone hydrochloride (NAL, 1.0μg), the antagonist of opiate receptors, into RT, enhanced sleep and reduced wakefulness.3.2 After simultaneous microinjection of MOR (1.0μg) and NAL (1.0μg) into RT, the wakefulness-promoting effect of MOR and the sleep-promoting effect of NAL were not observed compared with control.4. The effects of cAMP in RT on sleep-wakefulness cycle of rats Microinjection of cAMP (1.0μg) into RT increased sleep and decreased wakefulness compared with control; microinjection of methylene blue (MB,1.0μg) into RT enhanced sleep and reduced wakefulness compared with control.5. The effects of the 5-HTergic nerve fibers project from DRN to RT on sleep-wakefulness cycle of rats5.1 When L-Glu (0.2μg) was microinjected into DRN and normal sodium (NS,1.0μg) was microinjected into bilateral RT. We found that sleep was decreased and wakefulness was increased compared with control; when L-Glu (0.2μg) was microinjected into DRN and methysergide (MS,1.0μg), a non-selective 5-HT antagonist, was microinjected into bilateral RT, We found that sleep was enhanced and wakefulness was reduced compared with L-Glu group.5.2 When p-chlorophenylalanine (PCPA, 10μg) was microinjected into DRN and NS (1.0μg) was microinjected into bilateral RT, We found that sleep was increased and wakefulness was decreased compared with control; microinjection of 5-hydroxytryptaphan (5-HTP, 1.0μg), which can convert to 5-HT by the enzyme tryptophane hydroxylase and enhance 5-HT into bilateral RT, could block the effect of microinjection of PCPA into DRN on sleep-wakefulness cycle.

本研究采用脑立体定位、核团插管、微量注射、多导睡眠描记等方法，研究丘脑网状核(nucleus reticularis thalami，RT)中γ-氨基丁酸(gamma-amino butyric acid ，GABA)能神经元、一氧化氮(nitrogen monoxidum，NO)能神经元、阿片肽类神经递质、环一磷酸腺苷(cyclic adenosine monophosphate，cAMP)及中缝背核(nucleus raphes dorsalis，DRN)至RT的5-羟色胺(5-hydroxytryptamine，5-HT)能神经纤维投射对大鼠睡眠-觉醒周期的影响及其作用机制。1 RT内GABA能神经元对大鼠睡眠-觉醒周期的影响1.1大鼠RT内微量注射GABA合成关键酶抑制剂3-巯基丙酸(3-MP，5μg)，注射当天睡眠时间略有减少，第二日睡眠时间显著减少，觉醒时间明显增多，第三、四日睡眠和觉醒时间逐渐恢复至正常。1.2大鼠RT内微量注射GABA受体激动剂GABA( 1.0μg)后，与生理盐水组比较，睡眠时间增加，觉醒时间减少；而RT内微量注射L-谷氨酸(glutamic acid， L-Glu， 0.2μg)后，睡眠时间减少，觉醒时间增加；RT内微量注射GABAA受体阻断剂荷包牡丹碱(bicuculline，BIC，1.0μg)后，睡眠时间减少，觉醒时间增加；RT内微量注射GABAB受体激动剂氯苯氨丁酸(baclofen，BAC，1.0μg)后，产生了与GABA相似的促睡眠效果。2 RT内NO能神经元对大鼠睡眠-觉醒周期的影响2.1大鼠RT内微量注射NO的前体L-精氨酸(L-Arg，0.5μg)后，与生理盐水组对比，睡眠时间略有减少，但无显著性意义；而RT内微量注射NO的供体硝普钠(Sodium Nitroprusside，SNP，0.2μg)后可明显增加觉醒时间，缩短睡眠时间；微量注射一氧化氮合酶抑制剂L-硝基精氨酸(L-arginine，L-NNA，2.0μg)后，引起睡眠时间增多，觉醒时间减少。2.2大鼠RT内同时微量注射L-NNA(2.0μg)和SNP(0.2μg)后与L-NNA组比较发现SNP逆转了L-NNA的促睡眠作用；RT内同时微量注射L-NNA(2.0μg)和L-Arg(0.5μg)后，与L-NNA(2.0μg)组比较发现L-Arg可以增加觉醒而缩短睡眠，其促觉醒作用未能被NOS的抑制剂L-NNA所逆转。3 RT内阿片肽对大鼠睡眠-觉醒周期的影响3.1大鼠RT内微量注射硫酸吗啡(morphine sulfate，MOR，1.0μg)后与生理盐水组对比，睡眠时间减少而觉醒时间增加； RT内微量注射阿片肽受体拮抗剂盐酸纳洛酮(naloxone hydrochloride，NAL，1.0μg)后与生理盐水组比较，睡眠时间增加而觉醒时间减少。3.2大鼠RT内同时微量注射MOR(1.0μg)和NAL(1.0μg)后，与生理盐水组对比，原有的MOR促觉醒效果和NAL的促睡眠效果都没有表现。4 RT内环一磷酸腺苷信使对大鼠睡眠-觉醒周期的影响大鼠RT内微量注射cAMP(1.0μg)后与NS(1.0μg)组比较，睡眠时间增多而觉醒时间减少；RT内微量注射亚甲蓝(methylene blue，MB，1.0μg)后，与NS组比较，睡眠时间增多而觉醒时间减少。5中缝背核投射到丘脑网状核的5-羟色胺能神经纤维对大鼠睡眠-觉醒周期的影响5.1大鼠DRN内微量注射L-Glu(0.2μg)，同时在双侧RT内微量注射NS (1.0μg)后，与对照组(DRN和双侧RT注射NS， 0.2μg)比较，睡眠时间减少，觉醒时间增多；大鼠DRN内微量注射L-Glu(0.2μg)，同时在双侧RT内微量注射二甲基麦角新碱(methysergide， MS， 1.0μg )后，与对照组(DRN注射L-Glu 0.2μg，双侧RT注射NS 1.0μg)比较，睡眠时间增多，觉醒时间减少。5.2大鼠DRN内微量注射对氯苯丙氨酸(p-chlorophenylalanine，PCPA，10μg)，同时在双侧RT内微量注射NS (1.0μg)后，与对照组(DRN和双侧RT注射NS， 1.0μg)比较，睡眠时间增多，觉醒时间减少；大鼠DRN内微量注射PCPA(10μg)，产生睡眠增多效应后，在双侧RT内微量注射5-羟色胺酸(5-hydroxytryptaphan ， 5-HTP， 1.0μg )后，与对照组(DRN注射PCPA 10μg，双侧RT注射NS 1.0μg)比较，睡眠时间减少，觉醒时间增多。

This paper hereby introduces the cooling process of the common 160,000 m^3-in-capacity atmospheric LNG storage tank in China, the preconditions and matters to which attention is paid upon the cooling of tank. It also discusses some commissioning techniques needed in the cooling process, including pressure control, cooling medium supply and its flow control, process monitoring and cooling rate control, etc. The paper points out that the displacement of pipelines is easily to be overlarge and flange leakage takes place frequently in the cooling process and it gives corresponding solutions.

为此，详细介绍了国内LNG接收站常用16×10^4 立方分尺常压LNG储罐的冷却过程，分析了LNG储罐冷却前应具备的条件及注意事项，讨论了LNG储罐冷却过程中的压力控制、冷却介质供应及流量控制、冷却过程的监控及冷却速率控制等调试技术，指出了冷却过程容易出现管线位移过大、法兰泄漏等问题，并给出了相应解决方法。

During the course of the short-cycle correlation, This paper assembleds the descending cycle of early cycle and the ascending cycle of late cycle, which are conjointed together , begin to correlate and draw the ichnography . By this method , writer can consider the two connected sandbodies as one unit to analyse , and can contact the sand units of exploitatition in the oilfield. Then analyse the distributing and the continuity of the sandbodies in the medium-cycle, the distributing and the continuity of oil and gas in the short-cycle.

每个中期旋回包括 3-4 个短期旋回，在短期旋回的对比中，将垂向上相邻的早期短期旋回的下降半旋回和晚期短期旋回的上升半旋回组合到一起进行对比划分和平面成图，这使得相邻两套的粉砂岩作为一个单元进行分析，与油田开发中的小层紧密的结合到一起。

A cigarette production apparatus comprising a cooling water system for circulating a cooling medium along a perfume supply path connecting an application nozzle for applying a perfume to a roll paper with a pump for perfume supply to the application nozzle to thereby cool the perfume, wherein the temperature of cooling medium fed to the cooling water system is controlled by means of a cooling unit.

一种香烟制造装置，其沿着连接有在卷纸上涂敷香料的涂敷嘴和向该涂敷嘴供给香料的泵的香料供给路，设置有使制冷剂循环从而使上述香料冷却的冷却水系统，利用冷却单元来控制向该冷却水系统供给的上述制冷剂的温度。

This thesis developed physics model of radiant panel heating and cooling room based on previous studies. Computational fluid dynamics software FLUENT was applied to study the thermal environment of radiant panel heating and cooling room. The distributions of temperature and velocity of rooms of radiant floor heating and cooling, radiant ceiling heatingand cooling and radiant wall heating and cooling are gained.

本文在总结前人经验的基础上，分别建立了辐射板采暖和辐射板供冷房间的物理模型，利用商业软件Fluent对采用辐射板采暖系统和辐射板供冷系统房间内的热环境进行了模拟研究，分别得到了辐射板布置在地板、墙面和顶板三种不同方式下的采暖和供冷房间内的温度和速度分布情况。

The results showed that clay mineral of the sedimentary core B106 reveal seven palaeoclimate events since 16725 Cal.aBP, such as"Bolling Warming Events"in 13100±45 aBP,"Younger Dryas Cooling Events"in 10393±45 aBP,"Early Holocene Cold Event"in 8000aBP,"South of China Cooling Events"in 4624±35 aBP, Cooling Events in 3370±40 aBP, Drought Incident Cooling Events in 922BC and"Cooling Events of Northern and Southern Dynasty"in 514AD.

研究结果显示，B106柱的粘土矿物学指标指示出16725 Cal.aBP以来的7次古气候变化事件，分别是13100±45 aBP的&博林暖期升温事件&、10393±45 aBP的&新仙女木降温事件&、8000 Cal.aBP对应的&全新世最大降温事件&、4624±35 aBP的&中国南方降温事件&、3370±40 aBP的降温事件、922BC的干旱降温事件和514 AD的&南北朝降温事件&。

The results indicate that the cooling rate of melt droplet that can not break further depends not only on its diameter, but also on its position in atomizing chamber. As a result, the same sized particles in different positions show different cooling rates and two different kinds of microstructures. The cooling rates of melt droplets range from 104 to 108 K/s, and the critical cooling rate for glass formation of Al-Ni-Y is about 105 K/s. Moreover, the corresponding maximum diameter of amorphous particles is 25 μm, which accords well to the theoretical analysis results. The new approach, reflecting the complexity of close-coupled gas atomization objectively, is available and effective to evaluate the cooling behaviors of close-coupled gas atomization.

结果表明：在一定的工艺条件下，紧耦合气雾化存在多种破碎模式，熔滴的冷却速率因直径、雾化位置的差异，相同直径熔滴经历结晶和非晶化2种不同冷却行为；依据Al基合金粉末的粒度分布和微观结构，结合熔体的雾化过程及冷却模式，确定熔滴冷却速率的上、下限；实验得出熔滴的冷却速率为104~108 K/s，Al-Ni-Y合金的非晶化临界冷却速率为105 K/s，能形成非晶态的熔滴最大直径为25 μm左右，实验结果与理论分析结果较吻合，比较客观地反映紧耦合气雾化的复杂过程。

This study experimentally examined the heat transfer characteristics of 180-deg turning duct under forced convection cooling, as the internal cooling structure of 180-deg turning duct is widely applied to industrial cooling. While several perforated holes were separately arranged within the 180-deg turning duct, the cold flow of better cooling capability was guided in the first duct into the second duct in advance, so as to reduce the overheating of the second duct and realize uniform cooling of the machine members. In addition, the centrally separated holes could yield extra turbulence against the air current, and the interaction between bypass air current and mainstream may possibly improve the overall heat transfer capability.

本研究系以实验方法探讨180度转弯通道於强制对流冷却下之热传递特性，180度转弯通道之内部冷却构型在工业冷却之应用非常广泛，本研究设计将180度转弯通道其中间分隔具多个穿孔，目的在将第一流道内具较佳冷却能力之冷流提早引入第二流道，以减少第二流道产生过热情况，如此可使得机件获得均匀之冷却，此外，中间分隔上之穿孔对气流也具有额外之扰动效果、流经穿孔之旁通气流与主流交互作用，这都有可能增益整体热传能力。

Given the same total flow effusion from holes, the results show that the heat shield gets a higher average cooling effectiveness when the opening ratio is 3% compared with 6%; cooling effectiveness is sensitive to the height of ripple board, the heat shield gets the highest cooling effectiveness when the dimensionless height of ripple board is 1% compared with 2% and 3.33%; but there is a little influence on the cooling effectiveness of the liner with the change of the diameter of holes and the height of cooling passage.

研究表明：在气膜孔出流总量相同的情况下，3%开孔率比6%开孔率的隔热屏平均冷却效率较高；波纹板高度对隔热屏冷却效果影响较大，波纹板无量纲高度为1%比波纹板无量纲高度为2%和3.33%的隔热屏平均冷却效率高；孔径和冷却通道高度的改变对隔热屏冷却效果几乎没有影响。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。