查询词典 cooling correction

The results show that BS 460MPa grade reinforced bar can be produced all from Q235 or 20MnSi billet by the remained heat treatment process but the production cost of the former is lower. When the water pressure minishes, the intensities of reinforced bar reduce; the higher the temperature at the entrance of cooling bed is, the lower the intensities are. Therefore, the commendatory process parameters are that five stages coolers should be opened, water pressure should be all 1.8～2.0MPa and the temperature at the entrance of cooling bed of Q235 reinforced bar should lower than 650℃. The typical microstructure(Q235): the surface layer is tempered sorbite; the transition layer is pearlite and ferrite, and the partial ferrite is acicular; the core is pearlite and ferrite and the grain fineness is 8～10 grade. The yield strength is reduced by 10～20MPa after natural ageing and it can be simulated by artificial ageing(100℃×2h or 200℃×1h).

结果表明，Q235和20MnSi钢都可以利用余热处理工艺生产出性能合格的钢筋，但前者的生产成本较低；水压减小，钢筋强度降低，上冷床温度越高，强度越低，推荐5段水冷器全开，水压均为1.8～2.0MPa，Q235钢筋的上冷床温度应控制在650℃以下；钢筋典型的金相组织（Q235）表层为回火索氏体，过渡层为珠光体+铁素体且部分铁素体呈针状，心部为珠光体+铁素体，晶粒度8～10级；自然时效后屈服强度下降10～20MPa，用人工时效可以模拟自然时效，工艺是100℃×2h或200℃×1h。

The kernel of the idea is that CPMJI that involves two-phase heat convection, jet impinging and full vaporization is used to enhance the heat transfer potential of cooling medium and obtain the best cooling effect.

该方法的核心是利用低温喷雾射流冲击的低温气液两相射流冲击和充分汽化的强化换热优势，充分发挥冷却介质的换热潜力以获得绿色高效的冷却效果。

The desired cooling rate was achieved by simultaneously adjusting the cooling rate of argon-jet through the inner induction heating copper coil and the output power of the high-frequency generator controlled by the computer.

理想的冷却速度是通过同时调整冷却速度氩射流通过内铜线圈感应加热和输出功率高频率发生器所控制的计算机。

The investigation focused on the parameters affecting cooling effectiveness, including: opening ratio, height of ripple board, diameter of holes and height of cooling passage.

研究隔热屏的四种结构参数开孔率、波纹板高度、孔径和冷却通道高度的改变对隔热屏冷却效果的影响。

My company's main products are: BPS-150-type pre-stripping conveyor, conveyor plate, three saws, Zhuti planing machine hair, asked Ma Motor chest, OPZ-700-type bridge split half saw, TWX-100-type synchronous Wei seized line, ZBM-200 300Y-hair shaver machine, vertical plane of hair, hair-horizontal plane, XT-100 transport plane hoisted, the slope elevator, separated meat conveyor, packing conveyor, MX240-15 - Hoisted anchor chain conveyor, LXJ-2000-spiral pre-cooling machine, the 600 band saw, 300 DG band saw, dissolved wax - wax Baptist me, from Haneda machines, from hot-mix, pre-cooling machine screw, PBSJ tablet conveyor, Mao slaughtered chicken-blood lines, XPT-2000-Baptist scalding spray machines, hydraulic stripping leather machine, working platforms, barrels of cars, Ping Banche, and a variety of cold meat-slaughtering tools.

我公司的主要产品有：BPS-150型预剥输送机、平板输送机、三段锯、猪蹄刨毛机、托胸麻电机、OPZ-700型桥式劈半锯、TWX-100型同步卫检线、ZBM-200 300Y型刨毛机、立式刨毛机、卧式刨毛机、XT-100悬挂输送机、坡式提升机、分割肉输送机、包装输送机、MX240-15型锚链悬挂输送机、LXJ-2000型螺旋预冷机、600带锯、300DG带锯、溶蜡-浸蜡箱、脱羽机、烫脱组合机、螺旋预冷机、PBSJ型平板输送机、毛鸡屠宰控血流水线、XPT-2000型喷淋浸烫机、液压剥牛皮机、工作台、桶车、平板车、凉肉架以及各类屠宰工具。

The numbers of clusters made up of 1551 and 1541 bonded pairs representing the non-crystal structure occupy predominate position and the small numbers of clusters made up of 1431, 1661 and 1441 bonded pairs coexist in the non-crystal system at 4×10〓K/s cooling rate, thus there exist a large number of icosahedra clusters in the non-crystal system. The numbers of clusters made up of 1421 bonded pairs corresponding to the fcc-like structure occupy predominate position and the small numbers of clusters made up of 1422 and 1551 bonded pairs coexist in the crystal system during the 4×10〓K/s cooling process, thus the system can form the regular fcc-like structure.

在4×10〓K/s的冷速下，标征体系非晶结构的五重对称键型1551和1541所形成的小团簇数量在非晶体系中占主导位置，同时还存在少量的1431、1441和1661等其它键型形成的小团簇，这样，体系中含有大量的二十面体团簇结构；在4×10〓K/s的冷速下，标征面心立方结构的1421键型所形成的小团簇数量在晶体中占第一位，同时还存在一定量的1422、1441和1661等其它类型的键对所形成的团簇，体系最终形成面心立方结构。

The furnace body's ф2200×1500 outer covering main body is made of 12mm steel plate,installed sensor in the lower part 45°of furnace body, the sensor is weight 2 ton induction iron cores made from top gear's W-151 the cold rolling 0.35m/m made by Wuhan Steel Silicon steel plate Factory, primary manufactured the water cooling coil from 10×10×2 copper pipe, and installed stainless steelwater cooling cover, the power Frequency Induction melting Furnace 's metal melting fluid namely the sensor sencondary loop, the entire electric furnace is a transformer actually, match a 6 grades self regulating transformer, shift gears by the electric tank control, the voltage may from low to high,divide 6 grade to rise to 380V, each grade of voltage is different, the output power is also different, the furnace temperature is also different along with different grade,so can suit smelting colored or black and so on different melting point metals, and may use as new furnace lining fireproof to smeltdiamantine drying furnace.

炉体由12mm钢板制成Ф2200×1500外壳主体，炉体下部45°安装有感应器，感应器由武钢硅钢片厂生产的最高档的W-151冷轧0.35m/m取向硅钢片制成重2吨感应铁心，初级由10×10×2铜管制成水冷线圈，并安装不锈钢水冷保护套，工频有芯熔炼炉的金属熔液即为感应器的次级线圈，整个电炉实际就是一个变压器，配套一台6档的自耦调压变压器，由电柜控制换档，电压可由低到高，分6级升到380V，每档电压不同，输出功率也不同，炉温也随档位不同而高低不同，以适应熔炼有色或黑色等熔点不同的金属，并可作新炉衬耐火冶金砂烘炉之用。

By restricting accumulation of negative integral elements when performing integration by a proportional integral control unit until the actual temperature of a cooling target fluid reaches the corresponding target temperature, the method having this feature enables the control of the fan revolution speed so that the fan revolution speed rises immediately when the actual temperature of the cooling target fluid exceeds the target temperature.

通过限制积累负积分元素时，表演融合，由比例积分控制单元，直到实际温度冷却液指标达到相应的目标温度，该方法具有这项功能可控制风扇转速，使风扇转速立即上涨时，实际温度的冷却液指标超过目标温度。

Based on cooling condition,considering potential heat of phase transformation,the temperature field of lap joint and non-lap joint of high carbon steel wire on STELMOR cooling line are calculated.

根据高碳钢线材的冷却条件，考虑了相变过程的相变潜热，计算出线材搭接点与非搭接点在斯太尔摩冷却线上的温度分布，计算结果与实测结果吻合较好。

Trans-Blot Plus Cell 170-3990 Trans-Blot Plus Cell With Plate Electrodes and Super Cooling Coil, includes 3 gel holder cassettes, buffer tank, lid with power cables, 6 fiber pads, 1 pack blot absorbent filter paper (26.5 x 28 cm, 30 sheets), roller, stirbar 170-3991 Trans-Blot Plus Cell and PowerPac HC Power Supply Accessories 170-3994 Trans-Blot Plus Gel/Cassette Assembly Tray 170-3995 Fiber Pads, 27 x 28.5 cm, 2 170-3996 Blot Absorbent Filter Paper, 26.5 x 28 cm, 60 sheets 170-3997 Stirbar 170-3998 Trans-Blot Plus Roller, 6 wide 170-39 Trans-Blot Plus Gel Holder Cassette With Clamps 170-4990 Trans-Blot Plus Super Cooling Coil 170-4991 Trans-Blot Plus Platinum Anode Plate Electrode 170-4992 Trans-Blot Plus Stainless-Steel Cathode Plate Electrode 170-4995 Trans-Blot Plus Cell Buffer Tank 170-4996 Trans-Blot Plus Cell Lid With Cables 170-4997 Gel Holder Cassette Clamps, for Trans-Blot Plus cell, set of 3 9 规格:说明:运用Mini-PROTEAN II 多道筛选仪,可以快速有效地筛选 40 种不同的抗体或血清,无需把western

转印条件可调，能在很大的分子量跨度上获得最佳转印效果*耐用的板式电极能产生强大而均一的电场，而且电极在槽内的位置灵活可换；不论运行1、2 或3 个转印夹，电极间距可调节到最小以获得最大的场强和转印效率*凝胶支架转印夹保证整个凝胶与印迹膜表面的均衡接触*转印夹的铰链设计能防止凝胶滑动，便于转印夹组装*颜色标记的转印夹及电极板确保在转印槽内的正确定向*特级冷却芯和冷却水循环器进行温度调节―可理想地用于天然酶或高强度转印，或用于延长转印时间时减少缓冲液的损耗*可选择的组装盘是凝胶三明治和转印夹组装的理想选择 Trans-Blot Plus 转印槽能从单向和双向大格式凝胶上均一、高效地转移蛋白―配合使用新推出的 PowerPac HC 电源，多数蛋白都可在1530 分钟内完成转印。

You can snipe the second and third union leaders from this position.

您可以鹬第二和第三工会领袖从这一立场出发。

Aiming at the currently shortage of XML streams quality detecting, this paper proposes a new forecasting method of XML streams quality by least squares support vector machines, which is used the method of XML keys' vector matrix as windows, and vector product wavelet transform to multilevel decompose and refactor the XML streams series, that can fulfill real-time checking demand of XML quality, and ensure constraint, consist- ency and integrality. For even more adapting net load, it proposes a control strategy by weight and adaptive adjustment to ensure XML streams quality.

针对当前XML数据流质量检测存在的不足，提出构建XML键的矢量矩阵作为窗口，利用矢量积小波变换多级分解与重构XML数据流，再结合最小二乘支持向量机对XML数据流质量进行预测的一种方法，满足XML数据流质量重构时实时检测的要求，保证XML数据的约束性、一致性与完整性；为了更好的适应网络负载，采取加权与自适应窗口调整等调度策略充分保证XML数据流的质量检测。