查询词典 converter process

In the dehydrogenation process of HD process, the temperature set at 580℃ and pressure set at 100Pa is a perfect parameter, it can make the magnet to have high magnetic performance. In the HDDR process experiment, the paper contrast four HDDR process such as C-HDDR V-HDDR V-HD-S-DR and d-HDDR by the anisotropy and magnetic performance of ternary NdFeB magnetic material. The results show that adjusting the parameter of the d-HDDR process can make the anisotropy and magnetic performance of ternary NdFeB magnetic powders to catch up with the hexahydric NdFeBCoZrGa magnetic powders. At the end the paper discusses the betterment of the equipment which produces ternary NdFeB magnetic with the d-HDDR process.

和580℃的脱氢温度相搭配的脱氢气压选择在100Pa左右是理想的工艺参数，这样的搭配使得最终烧结磁体综合磁性能优异；在HDDR制粉工艺实验中，本文对比了C-HDDR、V-HDDR、V-HD-S-DR和d-HDDR四种HDDR工艺对于三元NdFeB合金各向异性和磁性能的影响，得出结论：通过发展d-HDDR工艺，调整工艺参数和控制水平，可以使三元NdFeB合金磁粉的性能达到或接近六元NdFeBCoZrGa合金磁粉的水平，在文章末尾，还对配合使用d-HDDR工艺设备的改造进行了分析。

During the intermissive fed-batch process, the feeding medium was added 10 times separately to make the total amount of C and N sources equal to those added in the batch process, and the yield of maduramicin was improved to 9645 μgmL^(-1), which is 15.7% higher than that obtained during the batch process. In the continuous fed-batch process, the maduramicin yield reaches 10328 μgmL^(-1), which is 6.0% higher than that obtained in the intermissive fed-batch process, and is 29.4% higher than that obtained in the batch process.

在间歇补料分批发酵工艺中，分10次补加培养基，使碳、氮源的总浓度与分批发酵相同，马杜霉素发酵单位提高到9645μgmL^(-1)，比分批发酵提高了15.7%；在连续补料分批发酵工艺中，马杜霉素发酵单位可达10328μgmL^(-1)，比间歇补料分批发酵提高了6.0%，比分批发酵提高了29.4%。

The results showed high class PbSt2 could be synthesized by this new saponifying process.Compared with metathetical process,the reaction time shortened,liquid-solid ratio and moisture content of filter cake decreased.Powder product could be prepared by one-step process,and particle product by two-step process.For the optimum processing conditions,the reaction temperature and time for one-step process were 65℃ and 10min,the amount of alkali added in the first step was 50%;reaction temperture and time were 65℃ and 10min for the two-step process.

结果表明，用皂化法工艺可得到优等品PbSt2，较复分解工艺，反应时间缩短、液-固比降低、滤饼湿含量比减小，一步式工艺得到粉状产品，二步式工艺得到颗粒状产品；最佳工艺条件为：一步式工艺反应温度65℃，反应时间10min；二步式工艺第一步的加碱量比50%，反应温度65℃，反应时间10min。

In this paper, two assemblies of special test equipments have been designed and fabricated by authors in our laboratory: namely Catalyst Molding Process Analyzer and Catalyst Mechanical Process Tester. These new skills are developed for the dynamic studies on whole mold forming process and crushing process of Fe-Cr WGHS catalyst pellet. Based on the orthogonal experimental design, the effects of some factors during the forming process of solid catalyst, such as predensification proportion, calcination time, calcination temperature and content of graphite on the mechanical strength of catalyst pellets are systematically examined, and the molding conditions have been optimized. Based on the experimental data, the relationship between catalyst density and forming pressure are educed, and the physical significances of some related parameters are described. The parameter of macro scopic elastic moduls has been suggested to character the mechanical properties of molding catalyst. The effects of molding pressure on mechanical properties of catalyst pellets are discussed, and results show that there exists a optimal molding pressure for the ideal mechanical properties: when over-high or over-low pressure is applied, the specific surface area and side crushing strength of catalyst pellets will decreased. The "rebound effect" will be undermined by the unsuitable pressure maintain process, resulting in the apparent decrease of mechanical strength of catalyst pellets.

本研究通过自行设计制造的催化剂模压成型过程分析仪（Catalyst Molding Process Analyzer， CMPA）和催化剂力学性质测试仪（Catalyst Mechanical Properties Tester， CMPT），以Fe-Cr系高温变换催化剂片剂为研究对象，对成型过程和受压破碎过程提供了全过程动态研究的新手段；本研究利用正交实验设计方法考察了固体催化剂成型过程中诸因素（包含预密致比例、煅烧时间、煅烧温度和石墨含量等）对催化剂成型体强度的影响，并对成型条件进行了优化；根据实验结果，关联确定了固体催化剂成型过程中的密度－压力关系式，并对方程中诸因子的物理意义进行了描述；提出了一种利用宏观弹性模量来表征成型催化剂的力学性质的方法；研究讨论了成型压力对催化剂成型体强度性质的影响，结果表明：对于催化剂成型体的强度和比表面性质，成型压力存在着一个最佳值，过高的成型压力会导致比表面积和侧压强度的降低；不适当的成型压力的维持时间会破坏&压力回弹&作用，造成催化剂成型体的机械强度明显降低。

A integrated mathematical model was established in accordance with the process of metallurgical production and it was composed of the process models and the raw materials distribution models. The process models include the sintering process model, the pelleting process model and the iron making process model.

数学模型分为6个子模型，其中工艺模型有烧结机优化模型、竖炉优化模型、高炉优化模型，物料配置模型有铁精粉优化配置模型，烧结矿优化配置模型和球团矿优化配置模型，模型之间交互的数据流为原料或产品的物料流量、物料性能、价格及原料性能的影子价格。

The paper firstly introduces the background, the present situation and meaning of the research on the embedded system. The research of key technologies of embedded ethernet remote measure and control system is carried out in this paper. Then the author detailedly illustrates the design process of hardware and software of the embedded remote measure and control system. The design process includes the selection and configuration of the 32-bit microprocessor, the selection of the memorizer, the selection and software design of the Ethernet Controller, the realization of AD data acquisition model and DA converter model.

本文论述了嵌入式系统的研究背景、研究现状及研究意义，对基于嵌入式技术的以太网远程测控系统关键技术进行了研究，详细介绍了系统的软硬件设计过程，包括32位微处理器的选择与配置、存储器的选择、网络控制器的选择及软件设计、AD采样模块与DA数模转换模块等外围电路的实现。

This invention concerns a current control process for a feed-in voltage converter, wherein a detected flux-inducing current component and a detected torque-inducing currrent component of an actual currrent vector of a rotating field machine are each controlled for a flux-inducing current component set value and a torque-inducing current component set value of the rotating field machine. To that effect, a control set-value (DELTA u*sp, DELTA u*sq) is determined, dependent each time upon a determined current component control deviation. From these, current components of an actual current vector are formed each time by overlay of a formed pilot value (u*spvor, u*sqvor). This invention also concerns a device for carrying out this process.

本发明涉及一种用于馈入电压式变流器的电流调节方法，其中分别将所检测的一感应式电机的一实际电流向量（i s 的磁通感应电流分量和一转矩感应电流分量i sq ）调节至该感应式电机的一额定电流向量的一磁通感应分量额定值和一转矩感应电流分量额定值，在这种情况下，分别根据所检测的一电流分量调节偏差计算出一调节器调节量（△u * sp ，△u * sq ），由这两个调节器调节量分别通过叠加所形成的一预控制量（u * spvor ，u * sqvor ）形成一额定电压向量的电压分量（u * sp ，u * sq ），本发明还涉及一种用于实施该方法的装置。

Active calcareousness, which has many advantages as the activator of steel-making residue, such as reducing the melting period, refining molten steel process, enhancing the purity and output of molten steel, decreasing the consumption of calcareousness and fluorite, increasing the life of converter, etc. is one of the basic raw materials introduced in steel-making industry. Besides it can be used in the purifying process of the molten steel.

活性石灰是钢铁工业的基本原料，它作为炼钢的造渣剂，具有缩短冶炼时间、提高钢水纯净度及收得率、降低石灰及萤石消耗、提高转炉炉衬寿命等优点，还可以应用于钢水精练过程。

The author analyzed total oxygen content, nitrogen content in steel made by typical process and the inclusion composition, change rule, morphology and distribution qualitatively and quantitatively by image analyzer, big sample electrolysis, SEM and energy spectrum analysis. The results showed that final inclusion form was small granule MnS, calcium aluminate, a small quantity of silicate and lumpy Al2O3. By intensifying deoxidation alloying process control in converter, argon blowing and slagging control and desulphuration and calcium reduction operation in refining course and overall-protection casting, the oxygen content was reduced by 20% above averagely, nitrogen content was reduced by about 10% and the inclusion content was reduced by 30%.

通过全O、N分析，夹杂物图像分析仪、大样电解、扫描电镜及能谱分析，定性和定量分析了典型工艺钢种钢中全O、N含量和工序过程夹杂物的构成、变化规律及形态、分布，分析钢中最终夹杂物表现形式主要为小颗粒的MnS、铝酸钙、少量的硅酸盐和块状Al2O3，通过强化转炉脱氧合金化工艺控制、精炼过程吹氩与造渣控制及脱硫和钙处理操作、全程保护浇注，钢水中O含量平均降低20％以上，N含量降低10％左右，铸坯中夹杂物含量降低了30％。

The updated development of production technology of clean steel in Shougang is introduced, including the end-point control of converter, LF-VD refining process and continuous casting process to prevent slag carryover and air reoxidation.

以转炉终点控制、LF -VD精炼及连铸过程防止卷渣和二次氧化为主线，简述了首钢近年来在洁净钢冶炼技术方面所取得的一些进展。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48