查询词典 controller

The field controller is a very important part of the EPA control system and it plays a very important role in the system.

而作为EPA控制系统的核心，EPA现场控制器设计和开发对EPA的发展有着重大的影响。

The epigenist computer is an industrial process controller and can have an intelligent behind management and on time display system operation information and other function.

上位机是工业控制计算机，主要完成智能化的后台管理和实时显示运行信息等功能，下位机是可编程控制器，主要完成现场信号和数据的采集及实时控制。

It is: sets the RFID label on the hanger, the card reader can get the information of the label and sends to the epigyny of the terminal unit of the station; when the hanger passes the reader of any working station; estimates the hanger whether or not enters the station to process manufacture after the epigyny receives the signal of the hanger, the programmable logic controller controls the pulling-in switch of the corresponding station according to the instruction from the epigyny.

该方法包括：在吊架上设有RFID标签，当吊架经过某个工作站进站口前的RFID读卡器时，读卡器会读到吊架标签上的信息，经由工作站终端设备发送给上位机；上位机接收到吊架检测信号后，判断此吊架是否进入工作站进行加工，可编程逻辑控制器根据上位机的指令控制相应工作站点的进站开关合上。

The thesis will discuss the resolution and experience of Danfoss Motion Controller used as remote servo control workstation in the Epsilon SWB epispastic molding machine's 4 axes position control.

本文谨以Epsilon SWB 发泡模机4轴位置伺服控制为例，介绍了丹佛斯运动控制器作为远程伺服控制工作站的应用办法和经验。

The thesis will discuss the resolutionand experience of Danfoss Motion Controller used as remote servocontrol workstation in the Epsilon SWB epispastic molding machine's4 axes position control.

本文谨以 Epsilon SWB发泡模机4轴位置伺服控制为例，介绍了丹佛斯运动控制器作为远程伺服控制工作站的应用办法和经验。

2B-7 can be set equal to zero by introducing an integrator into the controller.

方程 2-2B-7 的两个误差项都能通过在控制器中加入积分器而消除。

For a class of networked control systems with equality constraint ,this paper addresses the problem of designing controller,sampling period and the maximum allowable delay bound.

针对一类具有等式约束的网络控制系统控制器、采样周期以及最大允许延迟时间的设计问题，采用李亚普诺夫函数、线性矩阵不等式的方法，推导出了该网络控制系统渐近稳定的充分条件。

Then, according to the target of the controller design, the desired equilibrium point of the system is obtained.

然后，根据系统控制器的设计目标，确定了系统期望的平衡点。

Using the equivalence of thr original problem and P〓, the optimal controller can be designed.

关于这一部分，不论在方法上，还是在结论上都是作者所特有的。

For example, the Maximum Membership Function Principle is proposed in Chapter 2 on which the presently"scattered" ones among fuzzy mathematical operations for fuzzy control methods such as the acquisition of fuzzy relation, the composition of fuzzy relations and the fuzzy set projection algorithms can be unified to within a common theoretic frame; the geometric criterion for the redundant design parameters is developed for a class of fuzzy supervisory control algorithm in Chapter 4; such concepts as the metric equivalent distance between fuzzy rules are defined to realize the highly efficient reasoning process; consequently the strategy and algorithm for a dynamically commissioned fuzzy controller is given.

如在第二章中，提出了最大隶属度原则，从而将现有模糊控制方法中诸如模糊关系的获得、模糊关系的合成、模糊集的投影等"零碎"模糊数学运算统一到一个共同的理论框架之中；在第四章中，还针对一类模糊监督控制算法推导了其冗余设计参数的几何选取准则；为实现高效推理过程而定义了模糊规则间的距离当量等概念，在此基础上，提出了动态构造模糊控制器的策略和算法。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。