查询词典 control

To overcome the bad effect resulting from the nonlinearity time-variability and uncertainty on autopilot system performance during the motion process of aerodynamics missile, and to further improve the flight quality of missile, the autopilot system and used control method are researched. Firstly the integrant structure of system is discussed; then baaed un introducing the traditional PID method, controllers for missile attitude motion are designed respectively using fuzzy self-turning PID method and neural network self-adaptive PID method; at last a simulation experiment is finished. By comparing the simulation results that the designed controllers have good qualities is showed, and the feasibility and validity of applying fuzzy control and neural network into automatic control of aerodynamics missile is confirmed, and the base that other nonlinear control theory can be combined with the traditional control for missile to further improve the performance of missile control system is established.

为了克服飞航导弹运动过程中的非线性、时变性和不确定性对自动驾驶仪系统性能的不良影响，进一步提高导弹的飞行质量，对自动驾驶仪系统及其采用的控制方案进行了研究；首先对系统的整体结构进行了分析，然后在介绍经典PID方案的基础上，分别采用模糊自调整PID方案和神经网络自适应PID方案设计了导弹姿态运动控制器，最后进行了仿真实验；仿真结果的对比展示了所设计控制器良好的品质，验证了将模糊控制和神经网络应用于飞航导弹自动控制中的可行性和有效性，为其它非线性控制理论与导弹传统控制相结合以进一步提高导弹控制系统的性能奠定了基础。

Combining with the state of our research, the control strategy of the electronically controlled diesel engine and the design method of ECU have been put forward. All of these include determining control function, compartmentalizing the sub-functions, defining key of control links and control scheme have been brought forward. The control logic has been designed to meet the requirements of the control function of fuel injection and gas exchange system. The criterion of speed stable state has been proposed in this paper.

结合本课题的研究状况提出了电控柴油机的控制策略和电控单元的设计方案，包括控制功能的确定、子功能块划分、关键控制环节的确定，提出了两套控制方案，设计了控制逻辑以满足喷油、配气系统的控制功能要求，并提出了转速稳定状态的判据。

This control law could minimze the performance index in which the weighted state variables, control variables are included. By use of this control law, the aircraft is able to capture the desired flight states more accurately and decouples the control more completeiy with smooth control responses and less control engery.

这组控制规律使得对状态变量，控制变量进行加权约束的性能指标极小，并能用平缓的操纵反应和较小的控制能量使飞机达到完全解耦的指定状态。

Then a dynamic inversion tracing control method and a dynamic inversion fuzzy integrated control method are used to design depth control systems for a torpedo respectively. The simulation results illustrate that dynamic inversion fuzzy integrated control method can solve the problem of torpedo depth control more satisfactorily than the dynamic inversion tracing control method can.

提出了基于动态逆的跟踪控制方法和动态逆模糊集成控制方法，并分别将这两种方法用于鱼雷深度控制中，通过仿真说明动态逆模糊集成控制方法比基于动态逆的跟踪控制方法更好地解决了鱼雷的深度控制问题。

Professional Main Products are:(1) all kinds of electric locks Product Series: electromagnetic lock series, electric plug lock series, electric locking series lock series, hotel lock series, all kinds of special-shaped electric lock series;(2) sizes Intelligent Access Management Series: Single door machine, access control attendance machine, fingerprint access control machine, single-door two-way controller, two two-way controller, four one-way controller (communication mode may choose 485 or TCP / IP);(3) access control electric locks surrounding attachment Series: electric plug lock folder dedicated Frameless door, magnetic lock dedicated stent, the models go out button, a dedicated lock access control power supply, various types of access control card , EMID reader / issuer, and intercom access control system, a dedicated power lock delay.

专业主营产品有：（1）各式电锁产品系列：电磁锁系列、电插锁系列、电锁口系列、指纹锁系列、酒店锁系列、各式异形电锁系列；（2）大中小型智能门禁管理系列：单门一体机、门禁考勤机、指纹门禁一体机、单门双向控制器、两门双向控制器、四门单向控制器、（通讯模式均可选择485或TCP/IP）；（3）门禁电锁周边附件系列：电插锁专用无框门夹、磁力锁专用支架、各款式出门按钮、门禁专用锁电源、各类型的门禁感应卡、EMID读卡器/发卡器、对讲门禁系统锁延时专用电源。

Control have good sense on internal controlling Budgetary control with comparison analysis Credit Control Inventory and assets Control, especially CIP control Pricing and contract management Treasury Cash flow management Relationship with financial institutions Currency control and hedging.

高职专业是北科院的主导专业，共有计算机应用技术、计算机网络技术、汽车技术服务与营销、汽车运用技术、物流管理、生物技术及应用、旅游管理、商务英语、人物形象设计、艺术设计、法律事务、会计与审计12个专业。

To shorten the design period of control system of a satellite attitude control flywheel,and to verify the feasibility and effectiveness of design schemes,a control model based on a mathematics model for flywheels was established combined with acceleration techniques,reversal connection braking control and commutation control for the control system of flywheels.

为了缩短姿控飞轮控制系统的设计周期和快速验证设计方案的可行性及有效性，在分析姿控飞轮电机本体数学模型的基础上，结合该姿控飞轮控制系统所采用的加速控制、制动控制、换相控制，建立了姿控飞轮控制系统模型。

The compatibility of both Gvirens and B.firmus was researched. The fermentation filtrate of Gvirens , under the concentration of 70%, had not distinct inhibitory activity to B.firmus, the biomass of B.firmus would decrease with above the 70% filtrate of Gvirens, but the fermentation filtrate of B.firmus had not inhibitive role to Gvirens. 7, The cooperation control of both Gvirens and B.firm to the pine needle blight was explored:(1) Pathogen inoculation happened prior to the bio-control treatment for 7 days, however, the disease index and control effect had not distinct differences in any treatments even if combination of the two antagonists, but the susceptibility for different kind of pine were different.(2)when antagonist and pathogen were inoculated at the same time, some control effect to the pine needle blight, including certain extent cooperation control of both Gvirens and B.firm were proved, but it wasn't distinct when two antagonists used separately, and the change of the antagonist concentration had little effect to the control effect.

G.virens与B.firmus对松赤枯病的协同控制显示：(1)预先接种病菌后(7天)再进行生物防治处理，不管那种情况，感病指数和防治效果在处理间差异不明显，浓度影响无显著差异，即使是两种生防制剂联合作用也未显著提高其防效，但不同树种间的感病性有明显差异；(2)领抗菌与病原菌同时接种，对松赤枯病有一定防治效果，两菌联合有一定的协同作用，两菌分别单独施用防效差异不显著，浓度变化对防效影响不大；(3)预先接种颇抗菌能显著提高防治效果，两菌联合处理防效更优，感病树种的感病指数可降至13一15，抗病树种的感病指数可控制在3%左右；在同一浓度下B.f1'r功US、叹叮厂即s间无显著差异，在同一领抗菌下，浓度愈高，防效愈高：松，(4)三种生防接种方式的平均效果分析表明，叹F行ens最高平均防效49.5%黑 B。

All the indexes were tested in 2 -. 4 .. 6 weeks of operative intervals respectively. Results:(1) The general observation in the experimental group ,such as spirit, hair, body weight and activity ,was superior to that in the control group.(2) The recovery rate of sciatic nerve functional index (SF1) was statistically significantly higher in the experimental group than in the control group .(3) electrophysciological indexes: m the experimental group ,the tardy rate of induced motorius action potential ,recovery rates of the amplitude of compound muscle action potential and twitch tension and tetanic tension of triceps surae muscle ,were significantly higher than in the control group.(4) Compared with the control group ,the triceps surae muscle wet weight was significantly greater in the experimental group.(5) histomorphological indexes: the count of myelinated nerve fibers ,diameter of regenerated axon, thickness of nerve myelin sheath and area of capillary were much more in the experimental group than in the control group.(6) observation of ultrastructure with the transmission election microscope: more abundant organell a and maturer myelin sheath lay in the injured peripheral nerve of the experimental group, while not lay in the control group.

分别在木后第2、4、6周时进行各项指标的检测，结果发现：（1）实验组SD大鼠在整个实验过程中，其精神、毛发、体重，运动灵活性等一般情况优于对照组；（2）实验组的坐骨神经功能指数恢复率显著优于对照组，P＜0.01；（3）神经电生理指标：实验组运动神经诱发电位潜伏期的延迟率显著优于对照组，P＜0.05；复合肌肉动作电位振幅的恢复率显著高于对照组，两组比较第2周时P＜0.01，第4、6周时，P＜0.05；小腿三头肌单收缩力和强直收缩力的恢复率实验组显著高于对照组，P＜0.01；（4）小腿三头肌湿重的恢复率，第2、4周时实验组高于对照组，差异非常显著，P＜0.01；第6周时，差异仍显著，P＜0.05；（5）组织形态学指标：有髓种经轴突计数、再生轴突直径的恢复率，毛细血管面积，实验组均显著大于对照组，P＜0.01、P＜0.05、P＜0.001；实验组髓鞘厚度的恢复率也显著高于对照组，第2周时P＜0.01，第4、6周时，P＜0.05；（6）透射电镜超微结构观察：实验组再生轴突中细胞器丰富，髓鞘结构成熟，神经再生情况优于对照纽。

Wire electrode based on the trajectory of the different forms of control, WEDM can be divided into three types: one is shaped by the imitation controlled cutting in line in advance and work to create the same shape by mold, when processing the workpiece at the same time rough and on the mold clamping in the machine tool table, in the process of cutting wire electrode tightly against the mold on the edge of the track for the mobile, thus cutting out and die on the same shape and precision to the workpiece; another One is the electro-optical tracking control, to carry out the cutting line, before the basis of certain parts to enlarge the proportion of drawings depicts an electro-optical tracking map-processing machines will be placed in design stage of electro-optical tracking, tracking platform Photoelectric first line of graphics has always been to follow the track of the Mexican campaign, and then through the use of electrical, mechanical linkage to control the machine tool table, together with the workpiece so相似形wire electrode relative movement, thus cutting out the same shape and design to the workpiece; again a digital control, the use of advanced automatic control of digital technology-driven machine tool in accordance with the pre-processing parameters according to the workpiece geometry pre-processing procedures for the preparation of a good CNC auto-complete processing, the production does not require appearance on board the need to map to enlarge map of the previous two form of control has a higher machining accuracy and a broad range of applications, both at home and abroad more than 95% have adopted WEDM NC.

根据对电极丝运动轨迹的控制形式不同，电火花线切割机床又可分为三种：一种是靠模仿形控制，其在进行线切割加工前，预先制造出与工件形状相同的靠模，加工时把工件毛坯和靠模同时装夹在机床工作台上，在切割过程中电极丝紧紧地贴着靠模边缘作轨迹移动，从而切割出与靠模形状和精度相同的工件来；另一种是光电跟踪控制，其在进行线切割加工前，先根据零件图样按一定放大比例描绘出一张光电跟踪图，加工时将图样置于机床的光电跟踪台上，跟踪台上的光电头始终追随墨线图形的轨迹运动，再借助于电气、机械的联动，控制机床工作台连同工件相对电极丝做相似形的运动，从而切割出与图样形状相同的工件来；再一种是数字程序控制，采用先进的数字化自动控制技术，驱动机床按照加工前根据工件几何形状参数预先编制好的数控加工程序自动完成加工，不需要制作靠模样板也无需绘制放大图，比前面两种控制形式具有更高的加工精度和广阔的应用范围，目前国内外95%以上的电火花线切割机床都已采用数控化。切割属电加工范畴，是由前苏联人发明的，我国是第一个用于工业生产的国家，当时由复但大学和苏州长风机械厂合作生产的这是最早的机型叫复旦型，我们国内在此基础上发展了快走丝系统。欧美和日本发展了慢走系统LS

I am accused of being overreligious," she said in her quiet, frank manner,"but that does not prevent me thinking the children very cruel who obstinately commit such suicide.""

客人们在卡罗利娜·埃凯家里，举止就文雅一些，因为卡罗利娜的母亲治家很严厉。

Designed by French fashion house Herm è s, this elegant uniform was manufactured in our home, Hong Kong, and was the first without a hat.

由著名品牌 Herm è s 设计，这件高贵的制服是香港本土制造，是我们第一套不配帽子的制服。