查询词典 contour forging

Eurotech Benelux BV from the Netherlands is one of the leading European companies in Casting, Forging and Industrial Steel Structure Technology.

荷兰欧泰科技有限公司是一家在铸造，锻造和工业钢结构制造业处于领先地位的欧洲公司。

The January 2009 e-Pedigree deadline set by California may have been pushed back two years, but that didn't stop Biogen Idec from forging ahead with a solution.

在2009年1月电子谱系设定的最后期限加州可能已经推后两年，但并没有停止Biogen Idec公司从开拓一个解决办法。

There is no hammer in my hand without the ecology of blacksmithing, steel forging, iron-mining, transportation and retailing.

没有一把锤子不是经过打造、金属锻造、矿石采取、运输和销售的生态网络才制造出来的。

I'm standing on the starting line to take over the relay baton companions, right next one board foot, straining the feeding effort, forging ahead and go!

我站在起跑线上，接过同伴的接力棒，右脚往后一登，使劲了吃奶的力气，往前冲去！

Of course, the human brain, with its 100 billion cells forging 1 quadrillion connections, is breathtakingly complex.

当然，人类的由100亿个细胞形成了1万亿个连接的大脑是惊人复杂的。

This design is to dials forks the components the processing craft and the jig design, its components are the forging, has the volume to be small, components complex characteristic,Because the surface is easier than the hole to process, when formulation technological process, first the machined surface, then processes other take the surface as the datum,In which various working procedures jig all uses the unit clamp, special regarding processes the big end of hole, the trough and drills the capitellum hole incline eyelet in the working procedure, Chooses locate mode which two sells at the same time, and operates the simple manual clamp way clamp, its organization design is simple, the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计，其零件为锻件，具有体积小，零件复杂的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。

This design is to dials forks the components the processing craft and the jig design its components are the forging has the volume to be small components complex characteristicBecause the surface is easier than the hole to process when formulation technological process first the machined surface then processes other take the surface as the datumIn which various working procedures jig all uses the unit clamp special regarding processes the big end of hole the trough and drills the capitellum hole incline eyelet in the working procedure Chooses locate mode which two sells at the same time and operates the simple manual clamp way clamp its organization design is simple the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计，其零件为锻件，具有体积小，零件复杂的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。关键词拨叉，加工工艺，专用夹具，设计

Hoist chain using low-alloy steel forging, and quenching by the carburization treatment, has a very high tensile strength and wear resistance.

提升机环链采用低合金钢锻造，并经渗碳淬火处理，具有极高的抗拉强度和耐磨性能。

Because the cautery is deep usually,it's hard to see the forging handiwork from surface.

由于腐蚀一般都比较深，因此从表面上很难看出锻打工艺。

The research on microstructure pattern and mechanical properties of the circular ring parts by liquid forging experiment under different specific pressures and casting temperature s were stated.

通过圆环零件的液态模锻成形实验，对在不同比压和浇铸温度条件下，锻件的微观组织形貌和力学性能进行了分析研究。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48