查询词典 continuous distribution

We used NCAR/NCEPT anew analyze data and the method of bilinearity insert to fix on profile distribution of several physical field in the air on observation point and the stream field of 700hPa. We primary discussed the possible mechanism to influence aerosol size distribution.The atmospheric condition of 1000hPa~700hPa level had great influence on aerosol size distribution, and influence on coarse particle mainly below 850hPa level. The horizontal wind velocity of 925hPa level is a primary gene which contributed to coarse particles in the air. Vorticity profile especially below 700hPa level is a key gene to influence diffuse and convergence of local aerosol. The air vertical motion velocity greatly influenced aggregation and remove of aerosol particles. The vertical distribution of air temperature mainly influenced vertical transportation of aerosol.

利用NCAR／NCEP逐日再分析资料，通过双线性插值方法，确定观测点上大气中几个物理量的廓线分布；及700hPa的流场，初步探讨了影响大气中气溶胶粒子谱分布的可能机制： 1000hPa～700hPa的大气状况对气溶胶粒子谱分布影响显著，对粗粒子气溶胶的影响显著的主要集中在850hPa以下；925hPa的水平风速是影响大气中粗粒子气溶胶的一个主要因子；涡度廓线(尤其是700hPa左右及以下的涡度廓线)是影响局地气溶胶的扩散的一个关键因子；大气的垂直运动速度对气溶胶的聚合及移出影响较大；大气温度的垂直分布主要影响气溶胶垂直输送。

The results showed that the spatial distribution patterns of cochineal in cactus belonged to aggregation distribution, the basic component of distribution was individual population, the probability distribution was in accorded with negative binomial and the cochineal mainly distributed the second and third stem in cactus.

结果表明，该虫在寄主仙人掌茎片上的空间分布型属于聚集分布，分布的基本成分是个体群，概率分布符合负二项分布，主要分布在仙人掌的第2和第3级茎片上。

According to the geometric sense of classification problem and starting from dataset, four determinant algorithms for rotundity distribution, cirque distribution, sphericity distribution and columniation distribution are proposed.

本文利用分类问题的几何意义直接从数据集出发，按照两类样本点之间的距离关系，分别给出SVM训练集呈圆形、环形、球状、柱状分布的测试算法，为基于数据分布的核选择方法提供了实现的基础。

The major findings include:(1) By using fuel as the base indicator of relative efficiency, we found the following input factors' distribution inefficiency for domestic airlines: The distribution inefficiency of labor and capital input factors differs from airline to airline, and is becoming more severe with time; the distribution inefficiency of other factors does not differ very much among airlines but varies with time. It is inefficient from 1989 to 1995 but becomes more efficient during 1996 to 1997;(2) Airline companies have higher economies of density before 1996, but tend to show a constant return to density in 1997 when considering allocative distortions. The technical efficiency of input factors as a whole has declined after the open-air policy;(3) The costs of airlines are increasing significantly due to their distribution inefficiencies;(4) The instrument variable generated through a quasi price function does not have significant influence on cost; this may imply that airline companies in this time period did not exhibit the phenomena of high-quality high-price.

其主要结论如下：(1)藉由相对燃油分配效率探讨各投入要素之分配扭曲情形发现：劳动和因定投入要素之分配无效率因公司别而有所不同，且随时间而严重，唯民国86年稍有改善；其他要素之分配无效率则较不因公司别而有所不同，但亦随时间发生变化，初期为无效率，在民国85、86年则较具效率；(2)若考虑分配扭曲情形下，国内航空业在民国85年之前具有较高之密度经济，民国86年则趋向固定密度报酬；此整体投入要素之技术效率而官，在天空开放政策后其技术效率随时间变化而下降，但就燃油投入要素平均技术进步率而言，则其技术效率逐年增加且幅度明显；(3)航空公司因分配无效率所造成成本增加的情形相当明显；(4)准价格工具变数对成本之影响并不明显，此可能反映在此期间国内航空公司似乎并未趋向於高品质高价格之现象。

The distribution of the qualitative characters The performance of the 39 chief qualitative characters were observed and recorded,according to the test method of morphological characters in the .The results of distribution proportion of each character in cultivars group showed that the distribution of 32 characters(number of ray flower rings,floret curliness,shape of leaf base,size of stipule and so on) were very asymmetrical with near or above 70%cultivars concentrated upon one or two performance, however,the distribution of the other 7 characters(floret type,surface color of outer floret,back color of outer floret,color of disc floret,claw in base of sinus between lateral lobes,stem erectness and stem color) in the cultivars group were relatively symmetrical.

质量性状分布参照《菊花DUS测试指南》的形态性状测试方法，观察记录大菊39个主要质量性状的表现，计算各性状的表现式样在品种群内的分布比例，结果显示舌状花的重瓣性、花瓣曲反状况、叶片基部性状、托叶大小等32个性状的表现式样在品种群内分布极不均匀，接近或超过70%的品种集中在性状的1种或2种表现式样中；而花瓣形状、外花瓣表面色、外花瓣背面色、花中心部颜色、叶裂刻基部有无突起、茎的曲直性和茎色等7个性状的表现式样在品种群内的分布则相对均匀。4。

To accelerate the widespread of Synchronous Chip Seal and improve the operation quality of Synchronous Chipsealer, key techniques which influence the operation quality is studied detailedly, including the control of distributing quality, the dynamics characteristics of hydraulic system and the spray characteristics of asphalt nozzle of Synchronous Chipsealer.1 The factors which influence Synchronous Chip Seal quality are studied. Fiducial probability of simultaneous distribution density is advised to be used in evaluating the distribution bias and standard deviation of asphalt and aggregates simultaneously, which is more advanced than the single index evaluation method used before.2 The volume efficiency formula of asphalt pump is revised after analyzing the data of volume efficiency with mathematical statistics, which is helpful to match the asphalt spray system and control the flow out of asphalt pump accurately. With equation deduction and experiment, dynamic of hydraulic system used in Synchronous Chipsealer is studied, which lay the theory foundation on improving the stability and efficiency from design and controlling.4 Simulation on hydraulic system used in Synchronous Chipsealer is done with AMESim; the results indicate that multi-circle parallel connected hydraulic system with constant pressure power is better than that with load-sensing pressure power at present, because the latter will oscillate when the multi circles work at the same time. This conclusion has been proved during the debug of Synchronous Chipsealer.5 Asphalt nozzle characteristics, such as flat jet shape, flow distribution, are studied with experiment, the results indicate that cross quality of asphalt distributing is not increased linearly follow the increase of fan overlap level, the best point usually exists between two whole overlap level, asphalt distributing quality is better than±4% at the 2.5 overlap level, meets the superior specified in standard; The distribution quality of Synchronous Chipsealer can be increased by spray asphalt of different flow rang with nozzle of different diameter

为了加快同步碎石封层技术的推广，提高同步碎石封层设备的作业质量，本文对同步碎石封层设备作业质量的影响因素与控制方法、液压系统的动力学特性和沥青喷嘴的喷洒特性等关键技术进行了深入细致的研究：1研究了影响同步碎石封层作业质量的因素，提出了采用联合密度分布置信概率对同步碎石封层中沥青洒布量和碎石撒布量的系统偏差和标准差指标进行综合评价的方法，克服了传统评价方法只能对单一指标进行评价的缺陷；2采用数理统计的方法，研究了沥青泵的容积效率特性，修正了沥青泵容积效率公式，为沥青喷洒系统的匹配和沥青泵出口流量的精确控制提供了依据；采用数理方程推导与试验相结合的方法，研究了同步碎石封层设备液压系统的动力学特性，为从设计和控制的角度提高同步碎石封层设备液压系统的稳定性和效率奠定了理论基础；3运用AMESim软件对采用负载敏感控制和恒压控制的两种同步碎石封层设备液压系统进行仿真，结果表明：负载敏感控制的并联液压系统在多回路同时工作时，由于液压泵排量控制参考压力不稳定，容易引发液压系统振荡，恒压控制的并联液压系统是目前技术条件下比较理想的同步碎石封层设备工作装置驱动方案；该结论亦通过同步碎石封层设备装机试验得到了验证。4采用试验的方法对沥青喷嘴的喷洒特性进行了研究，结果表明：沥青洒布的横向精度并不是随着喷洒扇面重叠度的增加线性增加，其最高点通常出现在二个重叠度之间的"半重叠位置"，"2.5重叠"洒布时，沥青的横向洒布精度≤±4%，可以达到国家相关标准中的优级标准；同步碎石封层设备还可以根据不同洒布量情况下的流量需求，采用不同通径的喷嘴进行喷洒，提高沥青洒布精度。

It is seen from the fitting results between the frequency distribution curve and the empirical distribution dots that it is proper to use the generalized Pareto distribution to describe the probability distribution of the partial duration series.

从频率分布曲线与经验分布点据拟合的情况看，运用广义Pareto概率分布来描述部分历时序列的概率分布是合适的。

This article estimates the extreme loss distribution with extreme value theory, estimates the shape parameter with HKKP estimator, which is unbiased to small sample data, selects the right threshold by selecting smallest mean square error of the estimated cumulative distribution function and empirical cumulative distribution function and based on the extreme value theory method, this article estimates the extreme loss distribution and the p-percentile operational loss under certain believe range for Chinese commercial banks, then calculates the operational risk supervise capital.

本文利用极值理论对中国商业银行操作损失极端值分布进行估计，针对尾参数估计的来用传统Hill佑计对小样本数据容易产生偏倚的情况，提出了采用Hill佑计的改进―小样本无偏估计的HKKP佑计来估计操作损失的尾参数，针对由于阈值确定不准确导致结果偏差大的情况，采用最小化估计的累计概率分布与经验累计概率分布平均平方误差的方法确定较精确的阈值，估计出给定置信水平下操作风险损失的分位数，从而使得中国商业银行操作风险监管资本的测定成为可能。

By using the CFD software FLUENT, the inner-flow field of centrifugal fans with ruled-surface impeller versus with enveloping surface impeller has been simulated. The static pressure distribution, the dynamic pressure distribution, the total pressure distribution, the turbulent intensity and the speed vector of the two kinds of centrifugal fans are then analyzed and compared. From the calculating results, we found that the pressure distribution, the speed vector and other parameters of the two kinds of centrifugal fans are basically same. This implies that the tool-path generating arithmetic for the machining of the impeller can meet the aerodynamic requirements of the centrifugal fan. Furthermore the method can provide proof for designing department to establish sound manufacturing tolerance for impeller.

最后采用CFD软件FLUENT，利用标准k-ε湍流模型，采用分离隐式求解器，分别对直纹面叶轮离心通风机和包络面叶轮离心通风机整体风机内部三维流场和单个通道流场进行了数值模拟计算，在计算结果的后处理中，对相同坐标值处的静压力、动压力、湍流强度和速度矢量等参数进行了分析与比较，结果表明：在相同的计算参数条件下所得到直纹面叶轮离心通风机和包络面叶轮离心通风机内部流场差别不大，从而揭示所采用的叶轮数控加工的刀位规划方法的规划误差对流体机械动力性能的影响不大，这也为设计部门制定合理的叶轮加工公差提供了依据。

The following points are emphasized:The operation models of adiabatic and diabatic distillation have been set up and the operation block, thermodynamics model and mathematical model in the simulation have been determined as well;(2)Based on the simulation and exergy analysis with Aspen Plus program, shortcut distillation design—DSTWU model and rigorous distillation design—RADFRAC model, the author has determined the heat duty, exergy losses and the distribution of exergy losses along the adiabatic column, which will help the simulation and optimization of the diabatic distillation;(3)Diabatic distillation under various operation conditions has been simulated by using energy balance method and exergy analysis;(4)How the different mixture and the various degree of separation, number of trays and feed location influence exergy saving in diabatic distillation have also been discussed;(5)On the basis of the total exergy losses along the column, different schema of the heat transfer distribution along the column have been compared and analyzed;they can be classified in three categories: heat duty equipartition approach, empirical approach, separation degree matching approach. In conclusion, different heat transfer distribution along the column will have effect on total exergy losses. In particular, most satisfactory results have been obtained by using separation degree matching approach. In order to diminish the exergy losses, heat transfer distribution should meet the needs of the request of separation degree.And on this premise, the author makes his suggestion in increasing the proportion of heat supplied to the tray with minimum exergy losses and decreasing the proportion of heat supplied to the tray with the maximum exergy losses.

本文对透热精馏过程进行了模拟并对其节能效果的影响因素做了较为全面的分析和深入的研究，主要研究内容如下：(1)建立了常规精馏和透热精馏过程的模拟操作模块、热力学模型以及数学模型；(2)利用化工模拟软件Aspen Plus并分别采用DSTWU简捷模型和RADFRAC严格计算模型对常规精馏进行模拟计算和有效能分析，确定常规精馏塔的公用工程热负荷、有效能损失及有效能损失在塔内的分布，为透热精馏的模拟和优化提供数据参考；(3)对不同物系在不同分离度条件下进行透热精馏的模拟，分别采用能量衡算法和有效能分析法进行计算和分析；(4)探讨了各种因素如物系的选择、不同分离度、塔板数、进料位置对透热精馏节能效果的影响；(5)以全塔总有效能损失为比较基准，对热量在塔内的三种分布方案即热负荷平均分配法、经验法和分离度匹配法进行了对比分析并得出结论：塔内热量的不同分布方案对于全塔总有效能损失会产生影响，其中以分离度匹配法的节能效果最为理想，为减少有效能的损失，应使塔内的热量分布满足各塔板的分离度要求，并在此前提下，尽量减小有效能损失大的塔板的热负荷和增加有效能损失小的塔板的热负荷。

Putt your way through 36 fun-filled holes of minigolf on 3D designed courses with elevated greens, bunkers, bridges and water hazards, among other crazy obstacles.

您的推杆方式，通过36个有趣的填孔迷你的三维设计的课程，以提升绿党，掩体，桥梁和水的危害，除其他疯狂的障碍。

Some participles can be used either as attributes or as predicatives.

有些分词既可当定语用，也可当表语用。