查询词典 contiguous angle

Know relationship between the shape of squeegee and angle of application

知道胶刮子的形状，应用角度，力度，和移动速度对印网的影响。

The metal squeegee has the een shape and its print angle is about 30~45°.

它们由不锈钢或黄铜制成，具有平的刀片形状，印刷角度为30~45°。

Many factors such as composition, size and form, angle, pressure, and speed of the blade determine the quality of the impression made by the squeegee.

许多因素，如组成，规模和形式，角度，压力，速度和刀片确定质量的印象，由刮。

Simulation result shows that good images can also be achieved when the squint angle is up to 60 degree.

仿真结果表明，对给定的SAR参数，在斜视角为60°时，能得到较好的成像结果。

In this paper,the relationships among the Target Slope Angle,SSA and SA,and the calculation of SA were studied.

研究了扫描角、扫描起始角和目标倾斜角之间的关系以及扫描角的计算方法。

Pass to count to Wisterch parameter , and the steel wire is different from the molding tool get in touch with the length, and settle the path the research taking the length work the stabber angle to get under differently pull to stir the term, mold core adoption of best severally why size, combine the best work stabber of research the Cape, and settle the path to take the length nextly steel wire is in the molding tool of have fever to measure, air inside dispel-heat calories, winding dispel-heat on the coil-canister , and its molding tool dispel-heat calories of, and cause the steel wire the temperature difference pass in and outing the molding tool to influence steel wire machine function, under the experiment inside pull to stir the term according to the same race different work stabber Cape half of adoption the Cape(7 degree,10 degree,12 degrees, the best mold Cape, experience mold Cape) settle the path to take the length(2-3 mm,3-4 mm,4-5 mms, theories length, experience length) to proceed to experiment, and get the conclusion, work stabber the Cape then is more big the steel wire get in touch with the length with

通过对Wisterch参数，钢丝与模具接触长度、定径带长度、工作锥角度的研究得到了在不同拉拨条件下模芯采用的最佳几何尺寸，并研究最佳工作锥角、定径带长度下钢丝在模具中的发热量、空气中散热量、卷筒上的散热量及其模具散热量的不同，导致钢丝进出模具的温度差别对钢丝机械性能的影响，在实验中根据同种拉拨条件下采用不同工作锥角半角、定径带长度进行试验，得出结论，工作锥角越大则钢丝与模具接触长度越短，钢丝变形越剧烈，在模具中发热量就越高，导致钢丝出模温度高，使钢丝强度、硬度升高，弯曲、扭转次数降低，并且降低模具使用寿命。在其它条件相同的情况下，定径带越长则钢丝与定径带简壁磨擦增大，使钢丝发热量加大，从而使钢丝强度、硬度略升高，弯曲扭转次数略降低但定径带的增大减小了钢丝变形产生的弹性后效使钢丝出模直径比较稳定。

On this basis, this article, proposes the market development strategy of the microfinance company, specifically, designs the finance channel of the microfinance company , interest rates, regulation and supervision of the project and the motivation of staff from the marketing angle, by the way puts forward some problems about microcredit operation in future.

在此基础上，提出小额贷款公司的市场开发策略，并就资金的来源、利率的确定、对项目的规范和监管以及人员激励等方面的问题提出一些思考。

This essay takes it as the starting point a macroscopic and microscopic analysis of the factors in the staff drain from the angle of human resource development and management and further gives an evaluation of the major impacts on the hotel and the employees as a result of the staff drain. On the basis of a scientific analysis of the staff drafr cost, the expectation, attitude an...

本文从饭店人力资源开发与管理的角度，对产生员工流失的宏观和微观两大方面的因素进行分析，评估饭店员工流失可能给饭店和个人带来影响和后果，在科学分析流失成本、员工就业期望、态度和行为的基础上，设计、实施相应的政策，并对这些政策的效果进行评估，最后，从饭店人力资源管理的大局出发，选择有效的办法控制有价值员工的流失

The author the angle from staff member of SEO of sale of network of a gigantic peak, can't help the word is born by the heart, comprehending search engine is not this laborious spider, in everywhere net?

笔者从一位巨峰网络营销SEO工作人员的角度，不由得话由心生，感悟到搜索引擎不正是这勤劳的蜘蛛，在到处撒网吗？

The article the angle from teaching staff of a basic level, right " suddenly turn hostile " the chaos of type collects fees a few Baconian analysises, with period the attention that causes everybody.

本文从一名基层教育工作者的角度，对"变脸"式的乱收费作一些归纳分析，以期引起大家的重视。

A carrier gas such as nitrogen is directed through line 20 and valve 22 to connect with line 26 and mix with the gas sample.

如氮气之类的载体通过管线20和阀22引入，与管线26相通，与气体样品混合。

But for the most part, knaves and parasites had the command of his fortune

然而支配他的家产的大多是恶棍和寄生虫。