查询词典 contiguous angle

From the results, it is found that,(1) decreasing the angle between the air slot and the spinneret axis both the air velocity in the direction of the spinneret axis and the air temperature will be increased.

测试和模拟结果表示：(1)气流流道与喷丝孔轴线的夹角越小，喷丝孔轴线方向的气流速度越大，气流温度越高，但受结构设计的限制。

In this paper, based on nonlinear FEA software ANSYS/LS-DYNA, 3D dynamic simulation models of eighteen-type tubes for backward spinning was established. This paper not only obtained spinning force of tube backward spinning but also obtained the spinning force curves varying with the different reducer ratio, feeds, fillet radius for spinning roller, forming angle and diameter of spinning roller, and diameter blank inner.

以大型非线性有限元软件ANSYS/LS-DYNA为分析平台，通过对18种几何尺寸和参数不同的筒形件三旋轮强力反旋旋压过程的三维动态模拟，得到了它们的旋压力以及旋压力随不同减薄率，旋轮进给量，旋轮圆角半径，旋轮成形角，旋轮直径和毛坯内径的变化曲线。

Objective To explore the angle relation between spinous process and the pedicle of vertebral arch in image, and to decide the direction of screws of AF system.

目的 探讨参照棘突与椎弓根在影像学上的角度关系，确定术中AF螺钉的方向。

To decide the direction of the screw of AF system with the angle relation between spinous process and pedicle of vertebral is a valid idea.

利用棘突与椎弓根在影像上的角度关系确定椎弓根螺钉方向，是术中椎弓根螺钉定向的有效方法。

According to road designing data of mileage,coordinate,azimuth angle of tangent or straight line,curve radius,the length of spiral line from main point of curve or straight line starting point,we can calculate the coordinates of center line points and boundary line point s in any form of road under the same coordinate system.

根据线路设计资料提供的曲线主点里程、坐标、切线方位角、曲线半径、缓和曲线长度的已知数据，计算出任意线形的中桩、边桩在线路统一坐标系中的坐标，利用全站仪极坐标放样程序，以线路附近的控制点或加密点为测站，准确、快速放样各点。

Detect drive way too much space is a fixed power input shaft and output shaft rotation shaking, in the case of the transmission structure of conventional design and manufacture of machine tools, the transmission output shaft angle space at more than ten degrees to the dozens of degrees Transmission gap caused by too large spiral screw groove surface then there is obvious marks, thus affecting the machining accuracy of the screw.

检测驱动方式太多空间是一个固定的动力输入轴与输出轴旋转摇晃在常规情况下传动结构设计和制造的机床，传动输出轴角空间超过度到10度的数十个输电差距过大造成的螺旋槽螺旋面则有明显的标志，从而影响了螺丝加工精度。

It analyses and designs the method to test the twist liveliness of yarns and the index to test the spirality angle of the fabric.

分析设计了测试纱线捻度活性的方法和衡量织物纵行歪斜角的指标。

According to customers requirement, we can lathe all kinds groove on the rubber surface . groove line such as rhombus squareness herringbone linearly ,cycle spirality and so on . also the specification can make to measure such as angle of pitch、quantities of lines、deepth and width of groove.

英强公司制造的槽纹橡胶辊，可根据用户要求在胶辊表面加工各种的槽纹(如菱形、方形、人字形、直线形、环形、螺旋形等)，规格(螺距角、分头数量、槽深、槽宽等)可根据要求定制。

Different structural parameters length, width and depth of main microchannel, splay angle of main

通道角度、拐角的圆弧倒角、劈口的圆弧倒角）对检测灵敏度的影响。

That indicates the ply angle almost has no effect on the shear strength of splice laminates.

这也说明拼接层角度的变化几乎不影响层合板的剪切强度。

A carrier gas such as nitrogen is directed through line 20 and valve 22 to connect with line 26 and mix with the gas sample.

如氮气之类的载体通过管线20和阀22引入，与管线26相通，与气体样品混合。

But for the most part, knaves and parasites had the command of his fortune

然而支配他的家产的大多是恶棍和寄生虫。