英语人>网络例句>contact surface 相关的网络例句
contact surface相关的网络例句

查询词典 contact surface

与 contact surface 相关的网络例句 [注:此内容来源于网络,仅供参考]

The contact area and contact pressure in anteromedial and posteromedial quadrant tended to decrease, while, the contact area and contact pressure in anterolateral and posterolateral quadrant tended to increase.

结果]通过模拟试验发现,腓骨短缩时,胫距关节总接触面积呈减小趋势,外、后外象限的接触面积、接触压呈增大趋势,而前内,后内象限的接触面积、接触压均减小。

The contact area and contact pressure in anteromedial and posteromedial quadrant tended to decrease, while, the contact area and contact pressure in anterolateral and posterolateral quadrant tended to increase.

结果]通过模拟试验发现,腓骨短缩时,胫距关节总接触面积呈减小趋势,前外、后外象限的接触面积、接触压呈增大趋势,而前内,后内象限的接触面积、接触压均减小。

In view of the strict requirements of power line tensionless contacts on electric performance,the author expounds the electric contact mechanism of tensionless contacts in terms of contact resistance,factors influencing contact resistance and heating effect of the contact.

鉴于电力线路非耐张接头对于电气性能有较高要求,阐述了线路接头的电接触机理,包括接触电阻及其引起电阻变化的因素、接头的热效应。

Through field measurement for the contact pressure of box foundation with Ⅰ shaped plane of a high rise building on cobble subsoil, the distribution law of the contact pressure has been diagrammed. At the same time, the contact pressure has been calculated with finite compression layer model, which is well accordant with the measured result. The relative error of average value for the measured to the calculated contact pressure is 6.9%. This shows that the numerical calculation is right.

通过对西南交通大学某教学楼箱形基础基底反力的实测结果,得出了&Ⅰ&形平面箱基置于密实卵石层上的基底反力分布规律,又用有限压缩层地基模型对该箱基反力进行了计算,结果表明:实测反力与计算反力分布规律一致,实测反力平均值与计算反力平均值相对误差为6.9%,也说明此法计算箱基反力是可行的。

The contact fatigue strength was measured after the 20CrNi2Mo and 15CrNi6 steel used asdragging gear on quasi high speed locomotive was carburized and quenched as well as peened,com-pared with that of 20CrMnMo steel.The results shown that the contact fatigue strength limits of thesethree types of steel carburized and quenched essentially same,and the contact fatigue strength Iimit hasbeen increased by 5 porcent after peening,and that the failure appoarances of all contact fatiguespecimen were delamination ...

对20CRrNi2Mo、15CrNi6及20CrMnMo渗碳淬火齿轮及15CrNi6渗碳淬火+喷丸处理齿轮进行了弯曲疲劳试验,介绍了齿轮试件的设计与加工、试验装置与夹具、试验方法及试验数据的统计处理,试验结果表明,20CrNi2Mo和15CrNi6渗碳淬火齿轮在R=0.99时的σFlim分别为530MPa和375MPa,与20CrMnMo渗碳淬火齿轮相比,弯曲疲劳强度分别提高80%和27%。15CrNi6经渗碳淬火+喷丸处理齿轮在R=0.99时的σFlim为490MPa,比未喷丸处理者提高30%。

The computation model of two-point contact (for cone-tread) and conformal contact (for worn-tread) resulting from wheel flange close to rail is firstly established in this paper. A detailed analysis is made of the wheel/rail contact force, contact status and wheel/rail stress distribution on the different action of tractive forces and transverse forces. We draw some important conclusions, one of which is that the locomotive adhesion performance will decrease with the increase of transverse forces between wheel and rail.

本文建立了车轮轮缘贴靠钢轨形成的轮轨两点接触和共形接触的计算模型,对不同的牵引力矩、不同的横向力作用下的轮轨接触力、接触状态和轮轨应力分布进行了详细的分析,得出了轮轨间横向力增大会降低机车粘着性能等一系列重要结论。

In order to distinguish these two types of transitions, a state recognition method is introduced. We firstly propose a variable contact set in which the contact points on the robot body are defined to represent the alternation of the contact states logically. Then, by predefining thresholds for the contact forces, the state transition can be well recognized.3 As another research topic, the local tracking control according to the pre-acquired state transition trajectories plays an important role in realizing the non-regular motion for the humanoid robot.

在状态转换识别方法上,本文提出了接触点集合的概念,对接触状态的变化进行逻辑上的表达;再结合接触点集合的变化情况,通过设定接触力阀值来实现对状态转换的识别。3根据给定的状态转换轨迹进行局部的跟踪控制,是本文实现类人机器人非规则运动的另一个重要研究内容。

Contact angle between test solvent and filler or polymer matrix by the surface analysis.The surface tension, polar force parameter of the surface tension, apolar forceparameter of the surface tension and polar fraction had been calculated.

通过表面分析的方法,测出参比液在基体与填料表面的接触角e,计算出其表面张力Ys、表面张力的极性分量丫气、非极性分量Y as。

Firstly, to the particulate filled Polyurethane composites, we have detected the contact angle between test solvent and filler or polymer matrix by the surface analysis. The surface tension, polar force parameter of the surface tension, apolar force parameter of the surface tension and polar fraction had been calculated.

通过表面分析的方法,测出参比液在基体与填料表面的接触角θ,计算出其表面张力γ_s、表面张力的极性分量γ_s~p、非极性分量γ_s~d、极性分数P;并由此估算出了基体与填料所形成的界面的界面张力γ_、粘附功W_a、裂纹能γ_G。

Another approach in enhancing the light extraction efficiency of AlGaInP LED was accomplished using a surface roughening process. In this process, the Au(170 nm)/AuBe(260 nm)/Au(170 nm) ohmic contact layers were first deposited on the GaP window layer. After the alloy annealing process (480°C for 10 min), the Be atoms will diffuse into the GaP top layer and form non-uniform clusters. The LED samples were then immersed into a mixture 3H3PO4:1H2O2:1H2O solution for 6 min, resulting in a rough GaP surface. The luminous intensity of the AlGaInP LED can increase from 42 to 50 mcd, that is, an 18% enhancement can be achieved via the present non-photolithography surface roughening process.Keywords: LED, AlGaInP, Cu substrate, Reflector, Surface roughening

在实验的第二部份是开发磷化镓窗口层之粗化制程,我们是藉由正面金/铍欧姆接触电极之熔合制程,使铍扩散至磷化镓层,同时利用铍渗入磷化镓造成之特殊组成,可形成不均匀之蚀刻阻挡,而在磷化镓表面形成粗化,我们发现480℃、10分钟的熔合制程,加上浸泡磷化镓蚀刻溶液6分钟,可将四元发光二极体之发光亮度由42 mcd 提升到50 mcd,经由此无光罩粗化制程可将亮度提升18%,明显提升磷化铝铟镓发光二极体之外部量子效率。

第7/500页 首页 < ... 3 4 5 6 7 8 9 10 11 ... > 尾页
相关中文对照歌词
Intro
First Contact
Contact High (Demo)
Cracks In The Surface
Contact
Cypher With Self
Contact
I Have The Touch
Contact High
Eye Contact
推荐网络例句

The production moved off-Broadway to New York City, where she won the Joseph E. Calloway award for her performance, and was profiled in American Theater Magazine as one of ten young theater artists to watch.

生产提出过百老汇的新的纽约市,在那里她赢得了约瑟夫calloway奖,她的表现,并于异型在美国的战区杂志之一, 10战区的青年艺术家观赏。

It's a risk tradeoff, and I believe that adding test support code usually wins.

这是一个风险的权衡,我相信添加测试代码通常会占上风。

Besides, Fantine was only a moderately good workwoman

芳汀究竟还只是一个手艺平凡的工人。