查询词典 contact surface

The rapid solidification and grain growth of molten bath of laser surface remelting TA15 titanium alloy was a process of directly epitaxial growth of the b grains of the unmelted substrate at the contact of the melt-pool bottom.

分析表明，TA15钛合金激光表面重熔熔池的快速凝固是一个以熔池底部热影响区顶部与熔体接触的未熔母材b晶粒为衬底的直接外延生长过程，因此热影响区顶部与熔体接触的未熔母

The effects of the contents of the acrylate and vinylidene chloride on the contact angle on PET,the extend coefficient on PET and the surface free energy of the emulsion(γ1)were also studied.

通过对乳胶扩展系数、接触角和表面能的测定，研究了合成乳胶有关组份对乳胶粘接效果的影响，从而筛选出合成乳胶的最佳配方。

Results Through the experiment by membrane performance, the alginic acid sodium met the requirement, which became the membrane with the CaCl2 reaction at once. Its membrane was not dissolved in the water. And the characters of its 1%-3% solution were good on fluidity and surface contact angle determines. The biological compatibility of the compound of it with 20% CaCl2 solution was good.

结果：通过成膜性筛选实验，发现只有海藻酸钠符合要求，其与CaCl2反应能瞬间成膜，其膜不溶于水；通过测定其流动性和表面接触角度等，发现其质量分数为1%~3%的水溶液各种性能较好；其与质量分数为20%的CaCl2溶液反应成膜的生物相容性较好。

The contact tooth surface of the cylindrical gear with symmetrical arcuate tooth trace is analyzed with this method, and the results are compared with those got with the traditional TCA method.

用此法对弧形齿线圆柱齿轮进行了实例分析，分析结果表明此方法是正确可行的。

By making use of the proposed method, worm gear pairs with point contact tooth surface and good meshing characterist...

应用本文的原理，采用优化综合的方法，可以使圆柱蜗杆传动直接实现点接触和完全互换，并具有良好的接触特性，使对误差的敏感性降低，缩短装配中的辅助时间，且传动质量得到改善。

Being Compared contact angle changes of various adhesives on different surface of Moso bamboo and Chinese fir with the coefficients of penetrability, it was found that wettiability of polymeric diphenylmethane diisocyanate adhesive was much better than emulsion polymer isocyanate adhesive, wettiability of phenol-formaldehyde adhesive and urea-formaldehyde adhesive were in the middle of above two adhesives.

通过研究不同胶粘剂在毛竹表面的接触角变化，并结合胶粘剂渗透扩散系数，发现聚异氰酸酯胶在竹材表面的润湿性较好，而双组分乳液型聚异氰酸酯胶的表面润湿性较差，酚醛树脂胶和脲醛树脂胶润湿能力处于二者中间。

Besides, contact stress in tibia component-polyethylene insert interface of three component design arise 31% to 34% only in dorsiflexion 40 degree and plantar flexion 40 degree due to flat smooth surface design.

二件式人工踝关节的接触压力平均为7.8 MPa，三件式人工踝关节胫骨元件-关节内衬接触面的接触压力平均为4.4 MPa最小；三件式人工踝关节关节内衬-距骨元件接触面的接触压力平均为5.7 MPa居中。

The calculation results indicate that dropwise concdensation can be influenced considerably by surface topography and contact angle.

模型计算结果表明，表面形貌和表观接触角对滴状冷凝传热均有很大影响。

In order to further study the theory of dropwise condensation, the effects of surface topography of material and apparent contact angle on heat transfer in dropwise condensation are investigated in this paper based on the theoretical model of dropwise condensation established by former researchers.

为了从理论上对滴状冷凝进行更深入地研究，本文在实验的基础上对前人关于滴状冷凝的数学模型进行修正，考虑了冷凝表面形貌及表观接触角对滴状冷凝传热的影响。

Finally, in consideration of the interfacial interaction between liquid and solid, a new model for dropwise condensation heat transfer was proposed by using the population balance concept and considering the effect of surface topography and contact angle.

最后，针对液固界面相互作用对滴状冷凝传热的影响，以液滴数平衡概念为基础，考虑表面形貌和表观接触角对冷凝传热的作用，建立了新的滴状冷凝传热模型。

The labia have now been sutured together almost completely.The drains and the Foley catheter come out at the top.

此刻阴唇已经几乎完全的缝在一起了，排除多余淤血体液的管子和Foley导管从顶端冒出来。

To get the business done, I suggest we split the difference in price.

为了做成这笔生意，我建议我们在价格上大家各让一半。