查询词典 contact surface

Research on the Basic Kinematics-Geometry Theory and Tool Positioning Strategy for 5-axis NC Machining;2. The paper introduces the construction features of undevelopable ruled surface integral impeller and two 5-Axis numerical control mill machining methods of vane shape which are "line contact" and "point contact".

文章介绍了不可展直纹面型整体叶轮的结构特点及五坐标数控铣削加工叶片型面"线接触"和"点接触"两种方式，分析了采用侧铣加工产生误差的原因，对加工中的不同工步及精加工薄叶片的特殊处理进行了分析，并提出了相应的解决方案，对整体叶轮的数控加工有一定的现实意义和实用价值。

Analysis shows the new surface can extend the length of contact line effectively, and the contact ratio can be increased.

分析结果表明，由于所形成的齿面可以有效地延长接触线的长度，从而增大了重合度。

The contact angle is the angle between the tangent line at the contact point and the horizontal line of the solid surface.

接触角是角之间的切线的联络点和水平线的固体表面。

The conditions for the formation of different surface morphologies have been discussed in terms of the contact angle of SEPs at the interface between water and chloroform, and a contact angle slightly greater than 90o is found to be pre-requisite for the formation of honeycomb structures.

我们通过改变复合物中烷基链密度、烷基链长度以及多金属氧簇内核的尺寸，详细研究了复合物的亲疏水性和尺寸对所形成的多孔膜形态的影响，并在得到高度有序的多金属氧簇复合物有序多孔膜的同时，首次获得了有序多孔结构的形成规律，即只有界面接触角稍大于90o的复。。。

FEMOL is systematically applied to various moving boundary problems, including: membranes contact with rigid foundation, shape optimization of cross-sections of elastic torsional bar, seepage through a dam with a free surface, Mindlin-Reissner plates contact with rigid foundation, free Mindlin-Reissner plates on tensionless

三、将有限元线法分析推广应用到了一系列的动边界问题中，包括：薄膜接触问题，弹性扭转杆的截面优化问题，自由液面的稳定渗流问题，中厚板理论与刚性地基的接触问题，无拉力Winkler地基上自由中厚板问题，理想弹塑性扭转问题，理想弹塑性Ⅲ型裂纹问题。

Research on the Basic Kinematics-Geometry Theory and Tool Positioning Strategy for 5-axis NC Machining;2. The paper introduces the construction features of undevelopable ruled surface integral impeller and two 5-Axis numerical control mill machining methods of vane shape which are "line contact" and "point contact".

文章介绍了不可展直纹面型整体叶轮的结构特点及五坐标数控铣削加工叶片型面&线接触&和&点接触&两种方式，分析了采用侧铣加工产生误差的原因，对加工中的不同工步及精加工薄叶片的特殊处理进行了分析，并提出了相应的解决方案，对整体叶轮的数控加工有一定的现实意义和实用价值。

It is found that the contact angle of glass fiber reinforced unsaturated polyesterfluoridized by G-02 has increased from 49.3°to 74.7°, and the surface tension has reducedfrom 35.9 mN/m to 25.9mN/m accordingly. The contact angle of glass fiber reinforcedunsaturated polyester fluoridized by G-04 has increased from 49.3°to 79.7°, and the surfacetension has reduced from 35.9 mN/m to 24.5mN/m accordingly.

经测试发现经过G-02处理的聚酯玻璃钢表面对水的接触角由原来的49.3°增大到74.7°，表面张力也相应地由35.9mN／m减小到25.9mN／m；而由G-04处理的聚酯玻璃钢其对水的接触角由原来的49.3°增大到79.7°，表面张力也由35.9mN／m减小到24.5mN／m。

Numerical results for the contact load and real contact area are presented for real surface topographies resembling those of magnetic recording heads and smooth rigid disks.

联络装载和真正的联系范围的数字结果是类似那些录音磁头的真正的表面地势的presentedand使硬盘光滑。

On the basis of the Washburn principle , the contact angles of various liquids such as deionized water, sodium chloride solution of mass fraction 0.05, ethanol and ethanol-water solution of volume fraction 0.15 on the sediment surface were measured by the JF99A contact angle meter with osmotic pressure method.

根据Washburn原理研制的JF99A型粉体接触角测量仪，是利用渗透压力法测定粉体的接触角。

The static and dynamic characteristics of the beam of a gantry-type machining center are analyzed by means of ADAMS and ANSYS. Considering effect of gravity and cutting forces, the static deformation of the beam is obtained after calculating the interacting forces between the guide and the slide block by ADAMS. Moreover, the contact parameters of the guide surface are acquired by dynamic tests and parameter identification, then they are applied to the simulation model of the beam-slide box system, whose natural frequencies and modal shapes are achieved by modal analysis. Furthermore, the effect of changes of the contact parameters on the dynamic behavior of the beam-slide box system is also investigated.

对一种国产龙门式加工中心的横梁关键部件，采用机械系统多刚体动力学仿真软件ADAMS和有限元分析软件ANSYS进行了静动态特性分析；在考虑重力和切削力作用下，由ADAMS计算出导轨与滑块间的作用力，从而计算出横梁部件的静态变形；通过动态测试和参数辨识方法获得导轨结合面特性参数并将其应用到横梁滑箱系统整体有限元模型中，经过模态分析得到系统固有频率和各阶振型图，并进一步分析了结合面参数变化对横梁滑箱系统整体动态特性的影响。

The labia have now been sutured together almost completely.The drains and the Foley catheter come out at the top.

此刻阴唇已经几乎完全的缝在一起了，排除多余淤血体液的管子和Foley导管从顶端冒出来。

To get the business done, I suggest we split the difference in price.

为了做成这笔生意，我建议我们在价格上大家各让一半。