查询词典 contact rail

Contact with poison ※. Human skin with poison ivy, poison oak, poison ivy contact, will be severely stimulation, cause rashes.

接触毒※。人体皮肤与毒漆树、毒栎、毒常春藤接触，会受到严重刺激，引发皮疹。

Contact-impact model and its discrete schemes for revolute pairs with small clearances ;2. Based on the theory of contact dynamics,the dynamic model with clearances of sizing press roll was established using the method of numerical simulation.

基于接触动力学的理论，利用数值模拟的手段建立了调宽机含间隙的动力学数学模型，采用定步长四阶Runge-Kutta数值积分的方法，详细研究了运动副内间隙对接触力的影响规律。

Based on the theory of contact dynamics, the dynamic model with clearances of sizing press roll was established using the method of numerical simulation. The paper studied the effect of clearances on contact force inner Mechanism joints detailedly by the method of numerical integration of fix step length four orders Runge-Kutta.

基于接触动力学的理论，利用数值模拟的手段建立了调宽机含间隙的动力学数学模型，采用定步长四阶Runge-Kutta数值积分的方法，详细研究了运动副内间隙对接触力的影响规律。

Thus, the micro-convex contact at the top of the contact surface under the pressure of the law.

因此，微型凸接触，在高层的接触面的压力下，该法。

Based on researching contact Finite Element Analysis theory, a contact analysis prick valve pressurize through ANSYS is achieved.

介绍了液压领域里常用锥阀密封结构的接触密封机理，通过研究接触问题的非线性有限元理论，运用大型有限元软件ANSYS对锥阀密封结构进行了静态接触分析。

The terminal P2 of the primary winding is used as the static contact in the switch cabinet and it is with contact box.

本系列电流互感器为全封闭环氧树脂浇注结构，其一次绕组的P2端直接作为开关柜中的静触头，并带有触头盒。

By the solution method of the principal curvature and Boussinesq problems, the equations of the contact characteristics of the contact points on the face gear are developed.

利用曲面上任意点处主曲率的计算方法，得到了传动中圆柱齿轮和面齿轮上接触点处主曲率的变化规律。

The tongs all passes in the machine the gearing on the bed what tongs the gearing on realizes with superficial contact in the cowgirl on the bed in machine or matches.when the tongs installs in the machine bed work on the stage,the center of gravity of the tongs should be as far as possible low,center of gravity the more high an accepts should the dint is more big,the tongs bottom four directions should bulge,make its contact good,or the bottom establishes four a feets.when the tongs installs on the machine bed principal axis,the tongs install the to should have the enough match accuracy with principal axis cowgirl surface,and guarantee the gearing the stability dependable.

夹具体在机床上的安装都是通过夹具体上的安装基面与机床上的相应表面的接触或配合实现的。当物流设备需要的公司体在机床工作台上安装时，夹具的服装厂应尽量低，重心越高则支承面应力越大，夹具底面四边应凸出，使其接触良好，或底部设置四个支脚。当夹具体在机床主轴上安装时，夹具安装基面与主轴相应表面应有足够的配合精度，并保证安装稳定可靠。

A general contact algorithm for parallel finite element simulation of dynamic contact problem is presented in this paper.

引言工程领域存在大量动态接触问题，如旋转机械中运动部件与固定部件的摩擦、建筑物在地震或爆炸荷载作用下的破坏等。

The most likely solution to the problem is a single point of contact, with additional levels of contact information unlocked by us as we deem appropriate.

最可能的解决方案是建立一个联系界面，并由本人根据情况决定是否进一步提供其他合适的联系方式。

Nowadays, most of research are to build a transmutative Petri Nets through adding controlling place sets, controlling arc sets and controlling policy to the basic Petri Nets, while the Controlled Petri Nets could be used to argue many controlling theory problems conveniently and to induce many logically and physically supervisory and solve the Event Feedback Controlling Problems and State Feedback Controlling Problem in DEDS supervisory theory.

目前大多数的研究表现为在变形后的受控Petri网基础上，利用各种方法求得各种逻辑型、结构型控制器，解决DEDS监控理论中的事件反馈控制问题与状态反馈控制问题。

On one hand, there are discussions with the works council and union about extension of short time working up to the end of September.

一方面，有讨论，工程理事会和联盟关于延长工作时间短至9月底。