查询词典 contact point

It allows you to give people a contact point in all safety and anonymity.

它让你可以给别人一个完全安全而且匿名的联系方式。

This will give you the proper contact point for the one-handed backhand.

这将给你的单手反拍适当的接触点。

Chassis: made of channel iron, used to support power and to steady the ground and join contact point of all parts.

底盘：由铁管做成，用于提供能量并固定地面与所有连接点。

A design method of non-perpendicular pitch cone of the honing wheel is presented in this article. By adjusting the distance from the contact point of pitch cones to the axis of honing wheel, the relative velocity between pitch cones is ensured to be in the direction of the tooth trace of the gear.

提出了用于珩磨螺旋锥齿轮的非正交珩磨轮节锥面的设计方法，通过调整节锥面切点到珩磨轮轴线的距离，保证了节锥面之间的相对速度恰好沿着齿长方向。

Analyzing the honing principle of spiral bevel gears based on crossing-axis transmission, the mathematical model of the relative sliding speed of the contact point between honing wheel and gear is achieved. It is determined that the pitch cone of honing wheel depends on the number of teeth in the honing wheel and the angle between the common normal of pitch cones and the plane parallel to both gear and honing wheel axes.

分析了基于交错轴传动的珩齿原理，导出珩磨轮与被珩齿轮在啮合点处的相对滑动速度的数学模型，根据该数学模型可以判定珩磨轮的节锥面是由珩磨轮齿数、公法线和与珩磨轮轴线平行的平面夹角所确定。

When the current goes through the bimetal component with impedance, if the current increases or the environment temperature rises and the temperature reaches the preset value, the bimetal component will work and release the contact to shut off the circuit; and by contrast, if the device cools down to the safe temperature, the contact point will reset automatically.

电流通过有阻抗的双金属元件，遇非正常工作时，随电流增大或周围温度升高至设定温度值时，双金属元件迅速动作，打开触点，切断电路。当装置冷却到安全工作温度时，触点自动闭合，恢复正常工作状态。

When the current goes through the bimetal component with impedance, if the current increases or the environment temperature rises and the temperature reaches the preset value, the bimetal component will work and release the contact to shut off the circuit; and by contrast, if the device cools down to the temperature, the contact point will reset automatically.

电流通过有阻抗的双金属元件，遇非正常工作时，随电流增大或周围温度升高至设定温度值时，双金属元件迅速动作，打开触点，切断电路。当装置冷却到安全工作温度时，触点自动闭合，恢复正常工作状态。

Wire resistive touch screen technology, the grass-roots to the voltage field in both directions through the precision resistor networks are added to the work of conductive glass surface, we can simply be understood as the voltage field in both directions of staggered working hours added to the same work surface, The outer layer of Ni-Au conductive layer is only just be used as a pure conductor, there are time-test, after touching the inner ITO contact point X-axis and Y-axis voltage value method measured touch point position.

五线电阻技术触摸屏的基层把两个方向的电压场通过精密电阻网络都加在玻璃的导电工作面上，我们可以简单的理解为两个方向的电压场分时工作加在同一工作面上，而外层镍金导电层只仅仅用来当作纯导电体，有触摸后分时检测内层ITO接触点X轴和Y轴电压值的方法测得触摸点的位置。

Wire resistive touch screen technology, the grass-roots to the voltage field in both directions through the precision resistor networks are added to the work of conductive glass surface, we can simply be understood as the voltage field in both directions of staggered working hours added to the same work surface, The outer layer of Ni-Au conductive layer is only just used as a pure conductor, there are time-test, after touching the inner ITO contact point X-axis and Y-axis voltage value method measured touch point position.

五线电阻技术触摸屏的基层把两个方向的电压场通过精密电阻网络都加在玻璃的导电工作面上，我们可以简单的理解为两个方向的电压场分时工作加在同一工作面上，而外层镍金导电层只仅仅用来当作纯导体，有触摸后分时检测内层ITO接触点X轴和Y轴电压值的方法测得触摸点的位置。

The contact-point pressure must be within specifications, since low point pressure will allow the points to Bounce and Burn, and high pressure will cause rapid wear of the points, cam, and rubbing Block.

接触压力计：触点压力必须符合技术要求，因为触点压力低会使触点产生跳振和烧毁触点压力高会加快触点凸轮和顶块的磨损。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。