查询词典 contact angle

To make the design and manufacture of the spring contact more standardized,the authors analyzes the causes of such problem as contact resistance fluctuation of the spring contact in use,and proposes a corresponding structure design method of spring contact.Comparison and analysis are performed for the properties of cobalt bronze and beryllium bronze,and a standardized design scheme of spring contact is presented,in order to support the design,manufacture,operation and maintenance of GCB/GIS.

为了使弹簧触头结构的设计制造更加标准和规范，笔者对近两年来弹簧触头在使用中出现的接触电阻波动等问题的原因进行了分析，提出了相应的结构设计方法，对钴铜丝和铍青铜的材质性能进行了比对和分析，并给出了弹簧触头设计的规范化方案，对GCB/GIS的设计、制造、运行维护有一定的指导意义。

The gap element method is proposed in the paper for two kinds of problems, which include contact problem and gap joint problem. Elasticity contact problem falls into the category of unknown boundary value problems. It follows that the contact area and contact conditions or states can never be determined without special mathematical analysis, which is a very difficult work. The boundary conditions of the contact surfaces are deduced.

文中给出了间隙元法在空间可动部件接触问题中的应用，推导了其几何边界条件和力学边界条件，利用虚功原理推导了含间隙元弹性接触问题的有限元方程式，给出了其数值解法的迭代步骤，并指出了利用间隙单元进行分析的特点。

In studies of interaction among pile, platform that above it and surrounding soil, this paper employ the concept of plate element to simulate the loading character of platform, and employ the concept of solid element to simulate the character of pile and soil, using the finite element method after understanding the geometry properties of pile, soil and the platform. Analyzing the loading properties of the three entities above and their deformation, this paper also employ a special element, Penalty Element. The introduction of penalty element of this kind has served to guarantee the join harmony of displacement between solid element and plate element, thereby effectively resolving the join problem between platforms, pile that support it and surrounding soil.Considering significant property difference between pile material and its surrounding soil, there may be much shear stress on their contact interface produced under vertical load, thus causing displacement or fission. Therefore it is necessary to adopt one special constitutive law of this kind of contact interface, which can reflect its feature of loading and deformation thoroughly. On the basis of the deformation feature and constitutive laws of some contact interface obtained by Zhang Dongji and people concerned through some single-shear experiments on contact interface between structure and soil, this paper employ one pile-soil three-dimensional constant thickness contact interface model to simulate the " slide" taken place on the interface between pile and its surrounding soil. With this kind model, this paper has also created one finite element model, which can be applied to perform finite element calculation and analyze the pile-loading feature, and deduced its element stiffness matrix.

在承台-桩-土共同作用中，考虑桩与承台的几何特性，采用有限元方法，用实体单元模拟桩土，用板单元模拟承台，更具体地分析桩和承台的受力特性和变形，而且还采用罚单元—既实体单元与板单元之间连接必须满足变形协调条件，来有效地解决了承台与桩土的连接问题，且在桩土共同作用中，由于桩体结构的材料性能与周围土层性质相差较大，在竖向荷载下有可能在其接触面上产生较大的剪应力从而导致错动或开裂，因此，为了充分反映桩土接触面上的受力及变形特征，应采用一种桩土接触面特有的本构关系，即利用张冬霁等人关于结构与土体接触面单剪试验所得到的接触面变形特征及其本构关系，引入桩-土三维等厚度接触单元来模拟桩与桩侧土之间的&滑移&，在此基础上建立可用于桩基承载性状分析的有限元计算单元模型，并推导出了各单元的刚度矩阵。

The undercutting analysis probe the position of undercutting line and the spherical angle of spherical gears. Teeth contact analysis probe the kinematic error and the position of contact point of spherical gears with misalignment and ideal case. Another contact pattern analysis probe the positions and size of contact pattern ofspherical gears.

齿面过切分析主要探讨球形齿轮之齿面过切位置及过切发生的球形角，接触分析则讨论球形齿轮分别在具有装配误差及理想状况时之运动误差及接触点位置，另外，齿印分析探讨球形齿轮在受力变形后其接触椭圆之位置及大小。

As walk-off angle and acceptance angle of beam limit the conversion efficiency and the tunable wavelength range of difference frequency generation, research include effective nonlinear coefficient, walk-off angle and acceptance angle as functions of wavelength, the relationship between conversion efficiency and acceptance angle, and the impact of crystals length on the process of frequency conversion.

由于光束的走离角、允许角限制了转换效率和差频调谐波长范围，研究内容还涉及了有效非线性系数、走离角和允许角与波长的关系，转换效率与允许角的关系，以及晶体长度在频率变换过程中产生的影响。

Based on force diagram an analytical expression between some factors and splaying angle of the bar is brought forward, pointing out that splaying angle of the bar should be 2 3 degrees, and slitting angle should be 30 degrees approximately, outboard slant angle on the slitting groove should be 45 50 degrees and bite angle should be 7 8 degrees.

为稳定小规格带肋钢筋的三线切分轧制，对涉及棒材张开角的切分孔孔型诸角度进行了分析，通过对轧件受力状态的讨论，提出了诸因素与棒材张开角之间的解析式，指出满足三线切分稳定轧制时的棒材张开角应为 2°～ 3°，相应的孔型切分角为 30°左右，孔型外侧壁倾角应在 4 5°～ 5 0°之间，咬入角可控制在 7°～ 8°之间等。

Under the vertical load, the strength of rock mass is higher when there is only one group of joint and the dip angle is less than 20 or higher than 80; When dip angle is between 20 to 80, the strength of rock mass is much lower, it is smallest when dip angle is about 50, and it is lower when this kind of dip angle is in combination with other angle.

7在铅直向荷载作用下，岩体中只存在一组倾角小于20°或者大于80°时，岩体的强度相对较高；当岩体中存在一组节理的倾角在20°～80°间时，岩体的强度值很小，而且在与其他倾角的节理组合时，岩体的的强度值变化不太大，特别是当节理倾角为50°左右的时候，岩体的强度相对最低。

Exterior Opposite Angle Area : According to one angle area of the triangle, if we extend the two angle lines to the opposite direction, the area formed by the extending lines which like mirror area to the original angle is called here Exterior Opposite Angle Area.

外部对角映射区：针对三角形的一个角，将构成该角的两条相邻线段进行对角方向的虚线，这两条虚线围成的区域就是该三角形一个角的外部对角映射区。

Exterior Opposite Angle Area: According to one angle area of the triangle, if we extend the two angle lines to the opposite direction, the area formed by the extending lines which like mirror area to the original angle is called here Exterior Opposite Angle Area.

外部对角映射区：针对三角形的一个角，将构成该角的两条相邻线段进行对角方外部对角映射区向的虚线，这两条虚线围成的区域就是该三角形一个角的外部对角映射区。

With a dip angle between 15° and 30°, the uplift of an obducted plate during continental collision is much higher, and able to form a high mountain. The uplift is greatest with a dip angle of 15°; whereas with a dip angle between 30° and 45°, the subduction depth of a plate is much deeper, and able to form a deep basin. The subduction depth is greatest with a dip angle of 45°. When the dip angle is equal to or greater than 75°, subduction and obduction movements between two continents become undistinguishable.

当断裂带倾角在15~30°时，两个大陆板块碰撞导致的仰冲板块一侧隆升高度相对更大，利于形成高大的山脉，其中以15°倾角对应的仰冲板块一侧隆升最高；当断裂带倾角在30~45°时，两个大陆板块碰撞导致的俯冲板块的俯冲深度相对更深，利于形成深陷的盆地，其中以45°倾角对应的俯冲陆块一侧俯冲最深；当断裂带倾角≥75°时，两个大陆板块之间的相对俯冲和仰冲作用变得不明显。

Metrorrhagia is also gynaecological problems of common diseases.

崩漏是妇科常见病也是疑难症。

WordFTP gives you the convenience and timesaving you need.

wordftp让您的方便和省时您所需要的。