查询词典 connection angle

It is given that the connection between interception probability and orbit intersection angle as well as time error under the instance that the main body of objective satellite is destroyed. The choice of orbit intersection angle is expatiated when time error exists by simulation calculation.

研究了对目标卫星主体毁伤情况下，轨道交角和交会时间偏差与拦截卫星拦截概率之间的关系；阐述了有一定交会时间偏差时，轨道交角的选择情况，并对其进行了仿真计算。

When creating the finite element model, complicated connections among howitzer components are considered, especially the large displacement slide and the nonlinear spring connection between gun tube and cradle rail. The gun firing at 0°direction angle and 0°elevating angle is simulated with explicit time integration method and implicit time integration method, and the similar results are obtained.

在建立有限元模型时，考虑了火炮各部件间复杂连接，尤其是身管与摇架导轨间的大位移滑动接触和非线性弹簧单元连接等非线性问题；分别应用显式积分程序和隐式积分程序模拟了火炮在0°高低射角、0°方向射角工况下的发射过程，得到了相近的结果。

When dismantle the machine, firstly, stop the suspension coop on the lower 2 sections of the standard sections, the operation staff go on the suspension coop top, the hoisting machine loosen rope, lift the pillar with small shaft, pull out the horizontal pin of pillar, let the pillar fall slowly to thedismantled section's middle angle bar, insert the horizontal pin again. At this time, loosen the connection screw of standard section with spanner, hang the shaft of hand crane on the upper angle bar, sway the shaft of hand crane upward, separate this standard section from the next section, and lay itin the suspension coop, dismantle the other standard section for the same method, and turn the shaft to another direction, draw the lifting wire rope tightly, the operation staff leave the suspension coop, open the lock stopping instrument, fall the suspension coop to next position and lock the brakeinstrument, the operation staff return to the top of suspension coop, continually dismantle note: forbid the staff leave on the top of suspension coop or in the coop when the suspension coop is running

8.1折除时，首先将吊笼用停层装置停靠在待拆除的标准节的下两节上，操作人员上到吊笼顶，卷扬机松绳，用小吊杆将顶梁略向上提起，拔出顶梁横销，使顶梁值得徐徐降下，降到拆除节下一节中间框架角处，并重新穿上横销，这时用板手将标准节连接螺栓松开，将手摇起重机小吊杆钩挂在待拆节上框架用钢土，到吊笼内，用同样的方法拆下另一节标准节，然后将吊杆转向不影响升降机运行的方向，收紧起升钢丝绳，操作人员离开吊笼，打开锁止机构，使吊笼下降到下一个拆除位置，并将锁止机构锁死，人员重返笼顶，进行下一拆除循环（注意：在吊笼运行时绝不允许有人员留在吊笼顶部或吊笼内

With this important concept which the reads of wattmeter was equal to the product of the effective value of the voltage across the potential coil, the effective value of the current flowing in the current coil, and the cosine of the phase-angle between the current and the voltage. It was speciled with some examples to determine the phase-angle measured between line voltage, line current in different connection.

围绕有功功率表的读数等于该功率表电压线圈所接电压的有效值、电流线圈所通过的电流的有效值以及电压与电流相位差余弦的乘积这一重要的概念，用实例说明在不同的接线情况下如何利用各电量的相量关系来确定所测的线电压、线电流之间的相位差角。

By measuring the point features to obtain the orientation of the bone and by adding compesated cutting path, results shows that the angle error between the connection of Femoral and Tebial mechanical axis is 2.44 degree and the angle error is 0.75 degree in epicondylar axis, which met the error in practical requirement for total knee replacement surgery.

在本论文中已完成实物设计制作，最后以Saw bone作为切割实验，利用量测点取特徵点得其骨头方位并加入补偿值调整切割路径，其结果股骨和胫骨之连线与机械轴误差为2.44°、epicondylar axis角度误差为0.75°，以目前实验误差已可符合实际膝关节手术之要求。

Vision table the surface frame uses the high strength Steel Plate molding, four Connection Angle use the high quality steel plateconnection, the surface uses the ABS plastic decoration.

视力表的面框采用高强度钢板，四个连接角采用优质钢板连接，表面采用ABS塑料装饰。

Vision table the surface frame uses the high strengthSteel Plate molding, four Connection Angle use the high quality steel plateconnection, the surface uses the ABS plastic decoration.

视力表的面框采用高强度钢板，四个连接角采用优质钢板连接，表面采用ABS塑料装饰。

The connections studied herein were top-and-seat angle connection, including minor axis web connection and two type new connections designed according to the force-displacement character of minor axis joints.

进行了三种类型的梁柱弱轴角钢连接共9个试件的单调加载试验，其中两类试验试件采用本文根据梁柱弱轴连接节点受力变形特点设计的新型连接形式。

Size 1/2"(15mm) dual connection, solder or male IPS x 3/4"(20mm) hose thread connection, angle pattern

BD1C -通径DN15双连接，焊接或外螺纹铁管连接端口 x DN20软管螺纹连接端口，角式

Hose thread connection, angle pattern

BD2C -通径DN20可锻铸铁管连接端口 x DN20软管螺纹连接端口，角式

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。