查询词典 conical friction rlutch

Pitch circle diameter: d = mz = 3X12 = 36 Tooth crown heights: ha = m (f0 + x)= 3X (l +0.5)= 4.5 Tooth High: hf = m (f0 + cx)= 3X (l +0.25-0.5)= 2.25 Tooth full height: h = ha + hf = 4.5 +2.25 = 6.75 Addendum circle Chemical pumps diameter: Da = d +2 ha = 36 +2 X4.5 = 45 Fixed string tooth thickness: Sxn = m (π/ 2 * cos2a + xsin2a)= 3X (1.387 +0.6428 X0.5)= 5.125 Fixed string of high gear tooth thickness measurement: hxn = m (π/ 8 * sin2a + xsin2a)= 3X (0.7476X0.117X0.5)= 2.42 Modulus coefficient x0.5 m3 O20 ° pressure angle tooth thickness Sxn5.12 fixed string Addendum Coefficient string f1 fixed gear tooth thickness measurement most high hxn2.42 Teeth z12 2, shaft wear and tear maintenance: Axis gear pump wear is mainly because with the support roller shaft at both ends between the friction and wear, so that smaller shaft diameter.

分度圆直径：d=mz=3X12=36 齿顶高：ha=m（f0+x）=3X（l+0.5）=4.5 齿根高：hf=m（f0+c-x）=3X（l+0.25-0.5）=2.25 齿全高：h=ha+hf=4.5+2.25=6.75 齿顶圆直径：Da=d+2ha=36+2X4.5=45 固定弦齿厚：Sxn=m（π/2*cos2a+xsin2a）=3X（1.387+0.6428X0.5）=5.125 固定弦齿厚测量用齿高：hxn=m（π/8*sin2a+xsin2a）=3X（0.7476X0.117X0.5）=2.42 模数m3变位系数x0.5 齿形角o20°固定弦齿厚Sxn5.12 齿顶高系数f1固定弦齿厚测最齿高hxn2.42 齿数z12 2、轴的磨损维修：齿轮泵中轴的磨损主要是因为轴两端与支撑滚针间的摩擦磨损，使轴径变小。

The results show that friction force is larger than adhesive force.

结果表明螽斯的水平摩擦力大于垂直吸附力。

When existing liquid, the groove sample has biggest friction and the pit sample has biggest adhesive force.

有液体时，水平摩擦力是凹槽型的最大，垂直吸附力是凹坑型的最大。

Several special finite element techniques, such as the chip separation criteria, friction model, heat conduction and adiabatic shear during cutting process have been implemented to improve the accuracy and efficiency of the finite element simulation.

利用该有限元模型分析了钛合金铣削加工中切削力和切削温度的周期变化规律，建立了切削力和切削温度曲线。

But when the test load is increased, the wear mechanism is dominated by spalling, and the test material weight loss is raised, therefore, the amount of hard phases can be decreased advisably. high carbon high alloy steel, hard phase, friction and wear

以航空发动机供油系统用Cr18Mo16V钢为原料，研究其基体和碳化物硬质点的结构和组成，并分析

High purity aluminum or allumen (including 1% Zn, mass fraction) alclad on 2024 aerolite is usually employed for improving corrosion resistance. This alclad will greatly impact the mechanical properties of friction stir welded joint.

为提高2024航空铝合金材料的抗腐蚀性能，在其表面通常包有一层高纯铝或含Zn 1%的锌铝合金，包铝层在搅拌摩擦焊时会对接头的性能产生较大的影响。

But every time friction, the speed to be fast, should After light-weight, gradually afterburner.

而且每次做磨擦时，速度要快，应先轻后重，逐渐加力。

There is no mechanical contact, Chuan-power are generated in the air gap, except there is no other rail friction

1没有机械接触，传动力是在气隙中产生的，除了导轨外没有其它摩擦

When neccessary, Recycle water or Jet air can be used to take most heat friction produced.

必要时，可用循环水或喷气气流把摩擦产生的大部分热量带走。

Designed with air friction shaft,this machine can precisely control tension through air pressure.

该款机器装有空气摩擦轴，可通过空气压力准确地控制张力。

The Porsche Owner: But it's my car!

可，这是我的车呀。

LOX_83}{Oh, another bunch of wackos.

{LOX_83}{呃，又一群怪人。