查询词典 conical friction rlutch

The results indicate that as the value of fractal dimension is increased, the interfacial static friction coefficient first increases and then decreases; the interfacial static friction coefficient decreases as the fractal roughness parameter increases; while the inter-facial static friction coefficient increases as the material property or total normal load increases; the curve of static friction coefficient versus dimensionless total normal load is convex when the fractal dimension becomes smaller or fractal roughness parameter is larger or material property becomes smaller.

研究结果表明：界面的静摩擦因数首先随分形维数的增加而增加，然后随分形维数的增加而减小；界面的静摩擦因数随分形粗糙度参数的增加而减小，但随材料特性的增加而增加，也随总法向载荷的增加而增加；当分形维数较小或分形粗糙度参数较大或材料特性较小时，静摩擦因数－量纲一的总法向载荷曲线为凸弧。

The friction performances of carbon face were investigated with an inertia friction tester.The torque curve of carbon face was ideal,the coefficient of static friction was lower than that of dynamic in 0.28 MPa,the friction coefficient of static and dynamic decreased with the braking pressure increasing.To the fiber face,the coefficient of dynamic fric...

结果表明：碳质层的摩擦力矩在制动初期上升较快，中间过渡区平稳，尾部翘起较小；在制动压力小于0.28 MPa时静摩擦系数小于动摩擦系数，且动、静摩擦系数均随制动压力增加而减小；相对纤维层而言，采用碳质层摩擦时摩擦力矩曲线形态更好，连续制动时摩擦系数波动较小，磨损率低且能够有效保护偶件，是1种静/动摩擦系数比较低且适用于高载荷工况条件下使用的摩擦材料。

The results show that when the porosity of sample was higher, compressure rate was higher and resilience rate was lower, however resilient rate of sample with higher porosity were increased notably when pressure was increased, and it tended to accord with of sample with lower porosity. The friction coefficient was higher when porosity of paper-based friction material was higher, and the friction coefficient tended to reduce and stabilize when braking pressure was increased. The friction coefficient of sample with high porosity tended to reduce and stabilize in continuous braking cycles.

结果表明：在相同载荷下，随着孔隙率增大，材料的压缩率增加而回弹率降低，随着载荷增加，高孔隙率材料的回弹率先明显增大，而后趋于稳定；在相同比压和转速下，孔隙率越高，材料的摩擦系数越大，随着比压增加，孔隙率高的材料摩擦系数逐渐降低，且不同孔隙率材料的摩擦系数逐渐趋于一致；在连续循环制动时，高孔隙率材料的摩擦系数逐渐降低并趋于稳定。

By friction round shape of the different levels can be divided into cylindrical friction wheel drive, cylindrical trough friction wheel drive, three kinds of cone friction wheel drive.

按摩擦轮形状的不同，可分为圆柱平摩擦轮传动、圆柱槽摩擦轮传动、圆锥摩擦轮传动三种。

It is shown that the friction force and bulkhead thrust are the main factors of shield thrust setting, while the friction between the cutterhead and soil is the main factors of cutterhead torque setting. Friction force between shield and soil would make front soil of shield upheave, and subsidence of surface soil is induced by ground loss when the friction force between the cutterhead and soil results in the surface settlement asymmetrical distribution.

通过计算发现，盾构施工中盾壳摩擦和正面推力是盾构推力设置的主要因素，而刀盘与土体摩擦是刀盘扭矩设置的主要因素，盾构前方土体隆起主要由盾壳摩擦引起，刀盘摩擦作用主要引起地表沉降的非对称分布，地表沉降主要由盾尾空隙产生。

Friction rubber draft gear, as one of high-capacity draft gears, is developed after friction steel spring draft gear. Rubber has energy absorption capability and non-linear rigidity capability, so the friction rubber draft gear's capacity is usually higher than the friction steel spring bumper.

摩擦式橡胶缓冲器是继摩擦式钢簧缓冲器之后开发的一种大容量缓冲器，这种缓冲器利用了橡胶自身具有吸收能量及非线性刚度的特性，因此其容量一般比摩擦式钢弹簧缓冲器高。

The static friction and kinetic friction of cylinder are tested. The mathematical model of friction is presented. Then author proposes the mechanical method to improve the friction character of cylinder.

第二章研究了气缸摩擦力的特性，对静/动摩擦力进行了全面的测试，提出了摩擦力数学模型，并提出了改善气缸摩擦力特性的机械措施。

The flume experiments of equilibrium concentration in water and slurry have been done to determine the function between the kinetic friction angle and internal friction angle. The equilibrium concentration of debris flow calculated by the function between the kinetic friction angle and internal friction angle is quite close the equilibrium concentration data of debris flow in field.

通过实验确定以颗粒浓度和颗粒最大体积浓度为主的动磨擦角与静磨擦角的函数关系式，以该关系式计算的泥石流运动的均衡浓度与泥石流原型资料很接近。

The relationship between the effect of friction on the motion and the parameters, including driving velocity, the kinetic friction coefficient, the friction drop number between the static and kinetic friction coefficient, and the joint equivalent spring stiffness, is investigated quantificationally.

本文分别计算这两类系统受同样激励时的摩擦扰动均值比，进行对比研究，在相同参数条件下，包括动摩擦系数，静动摩擦落差数和激励幅值，摩擦对微振动系统的影响一般要大于对有限刚体运动系统的影响。

The friction, friction coefficient etc of prescind from external asperity model and the single asperity model in plasticity forming were respectively researched by using finite element analysis software ADINA and Coulomb friction model and nonlocal friction model.

应用大型有限元软件ADINA，采用库仑摩擦模型和非局部摩擦模型，对不考虑表面微凸的模型和单个微凸体模型在塑性成形中的摩擦力、摩擦系数等进行研究。

He paid $5,000 for this cupcake.

他我这个纸杯蛋糕花了5000美元。

I mean, if you want to, that is

我的意思是，如果你们想吃的话。