查询词典 conical friction rlutch

Analysis was also made on the influence upon the grinding forces in case of the same friction factor between wheel and workpiece at different grinding speed, as well as in case of different friction factor between wheel and workpiece at the same grinding speed.

分析了砂轮与工件表面之间的摩擦系数相同而磨削速度不同时对磨削力产生的影响，以及磨削速度相同而摩擦系数不同时对磨削力产生的影响。

It is usually the result of a hard, install incorrect wheel friction roller phase, or they may be due to a printing plate between the drum and rubber roller pressure; may also be because of the ink or paper of the particle due to friction.

它凡是是由于与刚健的、安设不不差的轮辊相摩擦引起的；也不定是由印版滚筒与橡皮滚筒之间的不张力过不小变成的；还不定是由于油墨或纸张洋的摩擦性的颗粒摩擦引起的。

A method to analyze the dynamics of piecewise continuous system is presented, based on it, the chaotic oscillation of a harmonically forced spring-mass system with friction is studied. The impact of friction and other parameters on the chaotic oscillation of this system is analyzed.

分析了系统参数和摩擦模型对系统混沌行为的影响；发现了摩擦模型的选取对系统动力学行为分析的重要性；揭示出在一定条件下，系统参数、环境条件或润滑条件的改变都有可能使系统进入无序的混沌运动状态。

To apply the friction spinning method in the medium or fine count range is one of the main targets of the research on friction spinning method at home and abroad.

将摩擦纺纱法引入细支纱领域，一直是国内外摩擦纺纱研究的主要目标之一。

In order to interpret the impact from different intensity of friction factors on urban development, a new model is developed by adding incidental cost and friction factors to the traditional Thunen Model.

为此，传统的杜能模型需要进行扩展，在原始模型的基础上加入偶然成本以及影响城市扩展的摩擦因子以对其进行完善，以便解释摩擦因子的不同强度对城市扩展的不同影响。

The protective film decreased the surface roughness, and also increaser the friction coefficient in the process BTA absorbed on SiO2 polishing particle surfaces, which decreased the friction coefficient in the polishing process caused by the particles.

另外，BTA对成SiO2抛光磨粒具有一定的吸附作用，进而对抛光效果产生一定的影响，抛光磨粒表面吸附层的存在会减小抛光过程中的摩擦系数。

The stiffness, stress distribution and contact status under different friction coefficients were obtained, and the influence of interleaf friction coefficient on the stiffness and stress was studied.

在不考虑摩擦和考虑摩擦两种情况下计算其刚度、应力分布和接触情况，研究片间摩擦对钢板弹簧刚度和应力的影响。

The key to this yield criterion is that the concept of internal friction angle which used in soil mechanics has been introduced to infer the relationships among poisson ratio, internal friction angle and relative density.

并且在Miss屈服准则的基础上论证了粉末体屈服准则在主应力空间，为一个回转椭球体。

Four-node degenerated shell element and rigid shell element are used in our FEM model.Updated Lagrange formulation and rate form constitutive equation are adopted to solve the problem of large strain and large rotation in sheet forming process.Sheet metal material property is described by plastic anisotropy yielding model and isotropic hardening model.Master surface-slave surface contact model is used to define the contact between tools and blank.Contact constraints are enforced with a kinematic algorithm and friction stress is computed by Coulomb friction law.Dynamic relaxation method is used to treat springback after forming stroke.

四结点蜕化壳单元和刚体壳单元分别用来建立板和模具的有限元模型；更新Lagrange法和速率型本构关系被用来处理板料变形中的大应变和大转动；材料模型采用塑性各向异性屈服与等向强化模型；通过主从面模型定义板料和模具的接触，接触算法采用运动约束法，摩擦力用库仓定律计算；并利用动力松弛法对回弹过程进行了计算。

In chapter six, A finite element model to evaluate the mechanics properties of thin wall structure is put forwards. The 4-node quadrilateral Hughes-Liu shell element with five through-the-thickness integration points is employed. The material is assumed to satisfy the elastic-plastic yield condition with isotropic hardening. The single surface contact algorithm is taken to deal with the contact searching. The priori stabilization procedures for the numerical control of the hourglass instability and the penalty method for the evaluation of contact force are used. The classical Coulomb law of friction is employed to evaluate the friction force.

第六章采用法向方向5点积分的4节点Hughes-Liu壳单元，前置参数法砂漏控制技术，等向强化弹塑性材料模型，分步增量应力回映方法，一体化接触搜寻算法，罚参数接触力计算方法及经典摩擦定律，建立了一种计算受冲薄壁结构大变形力学特性计算的有限元模型，通过对汽车A传动轴及汽车纵向方形吸能梁的大变形力学特性分析，验证了该有限元模型的正确性。

He paid $5,000 for this cupcake.

他我这个纸杯蛋糕花了5000美元。

I mean, if you want to, that is

我的意思是，如果你们想吃的话。