查询词典 conical bearing

In different conditions on fluidized state and stability of conical fluidized bed. The conlusions are: the conical angel of the conical fluidized bed is 20°, the fluidized state havesmall difference in conical distributor and distributor plate. The angle of conical bed increase,the fluidized state will have big difference. The angle is 60°and the conical as distributor, themass of fluidized is less, the most of material is the bottom of conical bed. The effect ofdistributor plate is much better than the conical distributor. Sawdust and rice hull can fluidize.The annular gap of conical distributor different, the angle of conical bed is same, the fluidizedquality of 10mm annular gap is better than the other conical distributors. The annular gap ismore wide, the conical bed have more slugging phenomenon and the pressure fluctuate is turnbig.In the experiment the flow of 2％and 4％distributor plates don\'t easy to control, becausethe pressure is very big and the pressure fluctuate of conical bed is too big.

在不同的条件下对锥形床的流化状态和稳定性进行了研究，结果得出：锥形床的锥角为20度时，分布锥和分布板的流化状态相差不明显，随着锥形床锥角的增大，分布锥和分布板的流化现象会出现明显的变化，锥形床锥角越大，分布锥的流化状态变化越明显，流化的的物料越少，大量物料都聚集在锥形床底部，而分布板在加料量少的情况下，能流化起来。10mm、15mm和20mm环隙分布锥在锥形床锥角相同条件下，10mm环隙分布锥的流化质量要好于其它两个分布锥，环隙越大越容易出现腾涌现象的产生，压降波动范围增大。2％、4％和6％开孔率分布板在本实验测定时，2％和4％开孔率分布板的流量不容易调节，同时产生的压降波动范围也很大，比较来说，6％开孔率分布板流化质量好些。

The main products include deep groove ball bearing, variation core roller bearing, cylinder roller bearing, british system bearing, variation core ball bearing, double row deep groove ball bearing, pillow block bearing, corner touch bearing, trust roller bearing, tapered roller bearing, and spherical roller bearing.

主营产品包括：深沟球轴承、调心滚珠轴承、圆柱滚珠轴承、英制轴承、调心球轴承、双列深沟球轴承、座架、角接触轴承、推力球轴承、圆锥滚子轴承和球面滚珠轴承。

The assembly of journal and plain bearing liner space is too little, force of organic still oil pressure is small it is the crucial index that affects lubricant result, make lubricate because of lacking engine oil between crankshaft and plain bearing liner and bite dead invalidation, include to be pulled badly, lack lube, layer of alloy of dry attrition generation is fused, grind sliding surface to did not maintain the oily film of certain ply, and all sorts of local overload exhaustion are destroyed, cavitation erosion and V form are destroyed etc, through technology of him director diesel locomotive old experience reachs the analysis of pair of its breakdown reasons, put forward precautionary measures especially. As a result of,the burns caustic mechanism plain bearing liner to burn caustic mechanism of 1 plain bearing liner is the lube film burst between journal and plain bearing liner, cause plain bearing liner and crankshaft generation clash, below high temperature, high pressure and high rotate speed, the wear-resisting alloy layer of plain bearing liner wears away prematurely or fuse, cause plain bearing liner and crankshaft to stick thereby bite, can make the steel back of plain bearing liner and Kong Zhong produces whirligig, inlet port is jammed, carry on the back by steel again with the friction of aperture causes high temperature to make plain bearing liner burned-out further, can cause bolt to break off, happen swing a malign accident that pounds cylinder body of bad internal-combustion engine.

轴颈和轴瓦的装配间隙太小，还有机油压力低是影响润滑效果的关键指标，使得曲轴和轴瓦之间因缺少机油润滑而咬死失效，包括严重拉伤，缺少润滑油，干摩擦产生合金层熔化，磨滑面没有保持一定厚度的油膜，以及各种局部过载疲惫破坏，气蚀和V形破坏等，通过本人主管内燃机车技术多年经验及对其故障原因的分析，特提出预防办法。1轴瓦的烧损机理轴瓦烧损的机理是由于轴颈和轴瓦之间的润滑油膜破裂，导致轴瓦和曲轴产生摩擦，在高温、高压和高转速下，轴瓦的耐磨合金层过早地磨损或熔化，从而引起轴瓦和曲轴粘咬，会使轴瓦的钢背和座孔中产生旋转运动，进油孔被堵塞，再由钢背和座孔的磨擦进一步引起高温使轴瓦烧坏，并会造成螺栓折断，发生甩出捣坏内燃机缸体的恶性事故。

The shaft is mounted in the pump housing by axially spaced conical bearings, each bearing including a first element fixed on the shaft with a first conical bearing surface concentric with the axis, a coacting second element carried by the housing with a second conical bearing surface concentric with the axis and slidably engaging the first bearing surface and a spring forcing the elements together.

所述轴由轴向地间隔开的锥形轴承安装在所述的泵外壳中，每一轴承包括：第一元件，固定在所述轴上，具有与所述轴线同心的第一锥形轴承表面；共同作用的第二元件，由泵外壳承载，具有与所述轴线同心的第二锥形轴承表面，该第二锥形轴承表面可滑动地啮合所述第一轴承表面；和弹簧，将所述元件压在一起。

On applying the theory of differential geometry, the research shows the procedure for determining the required cutter path for cutting conical cam profile using a NC milling machine based on the analytical profile expression of conical cam with oscillation conical roller follower or with a translating conical roller follower established in 3D space. The analytical expression of cutter path is provided for a tapered endmill cutter, whose size may be identical to or smaller than that of the conical roller.

应用微分几何理论，以在3维空间所建立的圆锥滚子摆动从动件和直动从动件圆锥凸轮机构凸轮廓面的解析表达式为基础，对数控铣床加工圆锥凸轮廓面所需刀具轨迹方程的建立方法进行了研究，根据所采用的锥形刀尺寸等于或小于圆锥滚子尺寸的情况，推导出相应的刀具轨迹方程的解析表达式。

The effect of tribology factors on bearing vibration is studied experimentally. AR model and WPT are used to processing the normal arid abnormal signals. The results are as follows:1. The vibration of ball bearings is caused by the tribology action of contact pairs of ball and ring races and has the essential of tribo-dynamics. Any factors affecting the tribology characteristics of contact pairs will affect vibration and noise of bearings consequently.2. Vibration characteristics of bearing keep almostly unchanged with the increasing of axial load expecting the increasing of nature frequencies. When radial load increasing with axial load unchanged, nature frequencies keep unchanged but some new vibration peaks appears in the spectrum.3. Vibration amplitudes are damped and nature frequency are enhanced with sufficient lubrication. Vibration and noise of bearings increase obviously and roar can happen and the contact surfaces scratch slightly under insufficient and unclean lubrication state. Bearing will be disabled in a few minutes without any lubrication.4. Bearing vibration is unstable under low speed. With the speed increasing, the vibration become stable and natural frequencies increase slightly but the amplitudes increase apparently.5. Bearing vibration can be excited only by some harmonics ofwaviness without lubrication and by all harmonics with lubrication based on the theoretical analysis.6. The nature frequencies of ball bearings decrease with the increasing sizes. When international clearance increasing, nature frequencies decrease in radial and increase in axial and angular and the amplitudes increase in radial and decrease in axial and angular. When the number of balls increasing, nature frequencies increase and amplitudes decrease. When the pitch diameter increasing, axial nature frequency increase and others nearly keep no change. When outer race groove curvature radius increasing, nature frequencies increase in radial and decrease in axial and angular and amplitudes keep no change in radial and increase in axial and angular. When inner race groove curvature radius increasing, nature frequencies decrease and amplitudes increase.7. The distortion in amplitude and frequency components of bearing vibration signals picked up by the present probe measurement method is founded and right conclusions cannot be achieved by the signals. When accelerometer is rigidly screwed with steel stud onto a flat outer surface of a ball bearing, vibration signal can be got without distortion and the reliability of research on bearing vibration is assured.8. AR model is suitable for large samples of bearing vibration signals, square root of length of samples can be used as the upper limitation of order determination and the FPE order selection criterion is effective. Many advantages of AR spectrum are founded over the classical based on FFT.9. Time-Frequency analysis is necessary for abnormal noise of ball bearings. WPT overcomes the principle shortcomings of STFT and proved to be a best tool to process the abnormal signals.

理论分析和试验研究表明： 1球轴承振动是钢球—滚道接触副中的各种摩擦学作用引起的，具有摩擦动力学的本质，任何对接触副的摩擦学特性有影响的因素都将对球轴承的振动和噪声特性产生影响； 2中心轴向载荷作用下，载荷增大使球轴承的固有振动频率升高，载荷越大同样的载荷增幅引起的频率升幅减小，足够大的中心轴向载荷作用下载荷的变化对球轴承振动的频率特性不会产生明显的影响； 3轴向和径向联合载荷作用下，径向载荷不大时球轴承振动的固有频率基本不变，但是可能引起变刚度激励的非线性振动，出现新的频峰，过大的径向载荷将使部分钢球脱离接触，使球轴承的振动和噪声呈现不稳定状态； 4润滑对球轴承的振动和噪声特性有重要的影响，良好的润滑对振动有明显的抑制作用，润滑不充分时，振动和噪声的水平会有明显增高，一定条件下还会激发接触副中的谐振，发出啸声，造成接触表面的伤害，无润滑干接触时，短时的运转就会损伤接触副表面，使振动和噪声迅速增大，并随时可能引发严重的磨损和卡滞失效；接触副润滑良好时，油膜的"刚化效应"使球轴承振动的固有频率有所提高，润滑剂中含有弥散性污浊时，振动的幅度总体升高，但弥散性污浊不会改变球轴承振动的频率特性；浙江大学博士学位论文：球轴承振动的研究 5低速时，球轴承振动的基本特征呈现不稳定状态，随着转速的提高，球轴承振动的频率特性趋于稳定，固有频率频峰升高； 6理论分析表明，干接触时钢球和滚道表面波纹度的某些谐波分量能激励球轴承的振动，振动的幅值与谐波幅值成正比，实际球轴承中钢球的分布不可能完全均匀，波纹度的激励作用会随时发生；润滑接触的分析表明，波纹度的任意谐波分量均能激励球轴承的振动； 7球轴承的几何和结构参数分析表明，球轴承尺寸越大，径向、轴向和角振动的固有频率越低；钢球中心圆直径增大，球轴承的径向和轴向振动的固有频率基本不变，角振动的固有频率有所上升，振动的幅频特性基本不变；径向游隙加大使球轴承的径向振动固有频率降低，轴向和角振动的固有频率有所升高，径向振动幅频特性的幅值升高，而轴向和角向降低；钢球的数量增多使球轴承振动的固有频率上升，幅频特性的幅值下降，径向振动的幅值下降最为明显；外圈沟曲率半径系数增大使球轴承径向振动的固有频率升高，轴向和角振动的固有频率降低，径向幅频特性基本不变，轴向和角向幅频特性幅值升高；内圈沟曲率半径系数增大使径向、轴向和角振动固有频率均下降，振动幅频特性的幅值均有升高； 8试验对比表明，传感器采用探针式安装时，由于探针接触副接触特性的影响，钡(量得到的球轴承振动信号有失真，采用专门设计和制作的试验球轴承，以固定式安装加速度计，首次测量得到了球轴承振动的真实信号，通过对振动信号的分析，验证了球轴承振动的理论模型； 9)基于时间序列分析的AR模型适用于大样本球轴承振动信号的分析，以样本长度的均方根值作定阶上界，FPE做判阶准则，给出的AR谱光滑，频率分辨率高，是球轴承振动分析的简便而可靠的手段； 10以时频域分析的小波包变换分析球轴承异音信号能够比较好地定位和聚焦异音发生的时间，时间间隔，频率范围，同样是球轴承振动分析的可靠的手段，可用作球轴承故障诊断技术。

Our company mainly manufactures under products: deep groove ball bearing series, self-aligning bearing, taper bearing (metric standard and inch standard), thrust ball bearing, car bearing, non-standard car bearing, pillow block spherical bearing, various bearing inner and outer ring forgements, various finished products inner and outer rings etc.

主要生产的产品有深沟球轴承系列、调心轴承、公英制圆锥轴承、推力球轴承、汽车轴承、非标汽车轴承、带坐外球面轴承、各种轴承内外套圈锻造和内外成品套圈。

Professional marketing at home and abroad note bearing plant bearing brand name: Harbin Bearing, Wafangdian Bearing, Luoyang Bearing, bearing in Changzhi, TIMKIN Bearing, SKF Bearings, FAG bearings, INA bearings, RHP bearings, NTN Bearing, NSK Bearings, NMB bearings, KOYO bearings, IKO Bearings, and other bearings.

专业经销国内外注名品牌轴承厂轴承：哈尔滨轴承、瓦房店轴承、洛阳轴承、长治轴承、TIMKIN轴承、SKF轴承、FAG轴承、INA轴承、RHP轴承、NTN轴承、NSK轴承、NMB轴承、KOYO轴承、IKO轴承等各类轴承。

The valve seat has a first conical partial surface and a second conical partial surface wherein the second conical partial surface is disposed downstream of the first conical partial surface and is raised in relation to it.

阀座(9)包括一个第一锥形部分面(109)及一个第二锥形部分面(209)，其中该第二锥形部分面(209)设置在该第一锥形部分面(109)的下游并相对该第一锥形部分面凸出地构成。

According to mineral components, ores of the Daixian rutile deposit can be classified into the following types: actinolite- bearing anthothyllitite, actinolite-garnet- bearing anthothyllitite, staurolite- actinolite- bearing anthothyllitite, actinolite-biotite-bearing anthothyllitite, kyanite-bearing anthothyllitite, talc-actinolite- bearing anthothyllitite and chlorite-actinolite-bearing anthothyllitite, etc.

山西代县金红石矿床的含矿岩石按岩石中矿物组成可以划分以下几种类型：阳起直闪岩、直闪阳起直闪岩、石榴石阳起直闪岩、十字石阳起直闪岩、阳起黑云直闪岩、阳起直闪岩、蓝晶石直闪岩、滑石阳起直闪岩、绿泥阳起直闪岩等。按金红石的颜色可以划分为两类，即红色金红石矿石、黑色金红石矿石。

Apllied the data of QuickBird-2——the highest resolution remote sensing,and based on the theory and methodology of fractal geometry,we have quantitatively studied remote sensing lineations in Gaolong gold deposit of Guangxi.

采用Quick Brid-2高分辨率卫星遥感数据，通过分形几何学的盒计维数法，定量研究广西高龙金矿区遥感线性构造。

So, sometimes, to change the color can not be your food (referring to the above-mentioned crustacean) has been a sign of boiling over.

所以，有时，来改变颜色，不能你的食物一直是沸腾了的迹象。