查询词典 cone

SZG series double cone rotating vacuum drier's main machine is double cone tank, let steam or heat water inside sealed jacket heat the inner shell in vacuum state, the hot transferred from inner shell to dump material, make water of the dump material gasify, low speed motor drying the tank along, make material up and down, from inside to outside, and change the heated surface, at the same time, vapour is taken out continually through vent-pipe of vacuum pump, increase the speed of drying, attain the purpose of uniformity drying at last, it is in conformity with the requirement of GMP.

SZG双锥回转真空干燥机主机为双锥形罐体，罐内在真空状态下，夹套内可通过内胆传递给湿物料，使湿物料中水分气化，低速电机带动罐体回转，物料不断上下内外翻动，更换受热面，同时，水蒸气通过真空泵经真空排气管不断被抽走，加快了物料干燥速率，最终达到均匀干燥的目的。符合药品管理规范"GMP"的要求。

The making process includes: setting insulating solid film on one horizontal rotating carrier with particle detecting unit and etching with single particle beam in the incident angle of 9.6-90 deg to penetrate the film, shifting the film relatively to the single particle beam and etching for the next time, and so on until the film is rotated by one turn to obtain truncated cone shaped, double turned truncated cone shaped or cylindrical single nanometer hole.

本发明将固体绝缘薄膜置于带有粒子检测装置的一个可水平旋转的载体上，用单粒子束刻蚀该薄膜，单粒子束入射角大于等于9.6°、小于等于90°，并且单粒子束在该薄膜底部、顶部、或二者之间与薄膜旋转轴交叉，待单粒子束完全穿透该薄膜后，固体绝缘薄膜底部的粒子监测器反馈使该薄膜被穿透处与单粒子束相对移动1荆再刻蚀，如此反复，直至固体绝缘薄膜旋转一周，获得圆台形、双倒圆台形或圆筒形的单纳米孔。

The company, dual-cone production capacity will reach more than 2,500 units, is the largest double-barrel screw cone production base.

目前公司锥双年生产能力达到2500多套，是全国规模最大的锥双机筒螺杆生产基地。

Our company specializing in the production of dual-cone, double-barrel, screw, double-, double-cone plastic extrusion machines, single screw extruder, plastic pipe production lines, plastic profile production lines, plastic sheeting, sheet production line, plastic extrusion To create materials and production lines dedicated to the production of environmental protection Plastic-wood extruder.

我公司专业生产锥双、平双机筒、螺杆，平双、锥双塑料挤出机、单螺杆挤出机、塑料管材生产线、塑料异型材生产线、塑料板、片材生产线、塑料挤出造料生产线及专用于生产环保塑木的挤出机。

The main products are standard twist drill stem Cone, Cone handles longer, long twist drill, various types of machine, hand cutter knife, the special-shaped cutter and the non-standard tool.

主要产品有锥柄标准麻花钻，锥柄加长，特长麻花钻，各类机用，手用绞刀，铣刀以及非标准的异型符合刀具。

All of these applications show that study on conic optimization is necessary. For detail, we conclude them as follows:The models, foreign and internal study situations on conic optimization and its dual problem are introduced in Chapter one, and we point out the key problem and research matter.Chapter two introduces some primary properties of a cone and its dual cone.

第二部分是应用实践：将所提出的锥规划及其对偶锥规划应用在各个领域，例如最小二乘问题、多项式求解、协方差矩阵估计，以及在其它方面的运用，这些应用无不显示出研究锥规划的必要。

Therefore this imaging system can realize two kinds of X-ray radiology: reverse geometry X-ray and X-Scan imaging, and several CT scanning methods, such as equiangular fan-beam CT, equispatial fan-beam CT, helical/spiral CT, cone-beam CT with circle orbit, cone-beam CT with circle-plus-line orbit.

这样就可以实现倒置结构的X射线成像方法、等角扇束的扫描方法，以及本文所提出的凹面源加点探测器的锥形束扫描方法，而且还避免了使用成组点探测器带来的性能不一致性。

In section three, we recall the mapping cone and show that the mapping cone is equivalent with the octahedral axiom if the other three axioms are satisfied.

在第三节，我们讨论了预三角范畴中的映射锥，证明了在其它三条公理满足的条件下，"映射锥是三角"与八面体公理等价。

By constructing a special cone and using cone compression and expansion fixed point theorem, we get the existence of positive solutions.

第二章在抽象空间E中仍然考虑第一章中的2n阶Lidstone奇异边值问题的解的存在性，其中f∈C[(0，1)×P，P]，且在t=0，1处具有奇异性。

By using the theorem on cone expansion and compression and a fixed point theorem on cone,this paper is concerned with the existence of positive solutions for some boundary value problem of singular nonliear semipositive second-order three-point boundary value problem,which improve many known results.

运用锥拉伸与压缩不动点定理研究非线性奇异半正二阶三点边值问题正解的存在性，推广了一些已知的结果。

By the time of its fall, most of the prisoners were writers who had written against the corruptions of the government.

到它被攻陷的时候，里面多数的犯人是写了反对政府贪污文章的作家。

The most obvious variation to ovum morphological character was that the color was changed from light green to sepiaceous in embryonic development, and all the ovums were almost hatched after 96h.

在胚胎发育过程中卵的形态特征最明显的变化是颜色从淡绿到深褐色，卵在发育96h后卵基本全部孵化。