查询词典 cone-nose

The cone cracking is a serious failure form on roller cone bit,which has negative effect to drilling safety.

牙轮破裂是指牙轮壳体整体或部分出现开裂现象，是牙轮钻头的一种严重失效形式。

The transmission ratio (cone/bit rotary speed ratio) of a mono-cone bit was tested on the bit test stand.

单牙轮钻头的牙轮转速与钻头转速之比是研究和设计钻头的重要参数。

On a wall of paper, Latham drew a simple form, such as a cone, at the top center, and then filled the rest of the space with gradually complexifying cone shapes.

在有一墙之高的论文上，拉萨姆绘制了一个简单形态，比如在顶端中心的一个圆椎体，然后用逐渐复杂的圆锥体形态填满剩下的空间。

On a wall of paper, Latham drew a simple form, such as a cone, at the top center, and then filled the rest of the space with gradually complexifying cone shapes.

在一堵纸质墙面上，拉萨姆绘制了一个简单图形，比如在墙顶中间画一个圆椎体，然后用渐趋复杂的圆锥体形填满剩下的空间。

On a wall of paper, Latham drew a simple form, such as a cone, at the top center, and then filled the rest of the space with gradually complexifying cone shapes.

在一堵纸质墙面上，拉萨姆绘制了一个简单图形，比如在墙顶中间画一个圆椎体，然后用渐趋复杂的圆锥体图形填满剩下的空间。

Coning and quartering method: put the sample onto the steel plate in the form of a cone; each scoop shall be inserted from the top of conical to make it spread along the top evenly, and pay attention not to misplace the center of cone; do it at least 3 times and mixed thoroughly; then flatten the top and use the cross plate from top to bottom to divide into 4 equal segments, randomly take out 2 oppositesegments and do it repeatedly for several times and finally divided into not less than the minimum retained quantity.

圆锥四分法：将样品置于已用样品刷好的钢板上，堆成圆锥形，每铲由圆锥顶尖落下，使其均匀地沿锥尖散落，注意勿使圆锥中心错位，如此反复至少移堆三次，使其充分混匀，然后将锥尖压平，用十字板自上插下，分成四等份，任取两个对角的等份，重复操作数次，缩分至不少于最少留样量。

Card sets of connections, in China only developed in recent years, it's connecting and sealing principle is that when the nut tightened up, the card sets under pressure to edge into the tube outer wall of the Department of bite, card sets and outside the cone with the joint under pressure All cone density in vivo, which can reliably prevent the leakage.

卡套连接，在我国近年才发展起来，它的连接和密封原理是，当旋紧螺母时，卡套受到压力，使其刃部咬入管子外壁，卡套外锥面又在压力下与接头体内锥面密合，因而能够可靠地防止泄漏。

In the design of expension tool, the cone angle is the key, because it must satisfy the plastic extreme condition of the expension tube and reduce the upgoing frictional resistance of the expension cone to minimize the possibility of tool sticking. It is preferred that the material quality of expension tube must differs from that of casing and the yield limit of expension tube must be less than that of casing, which is favorable to protect casing.

在膨胀工具结构设计中，锥角设计是关键，除了要满足膨胀管达到塑性极限条件外，还应综合考虑膨胀锥上行的摩阻尽可能小，以减小工具卡死的可能；膨胀管的材质应与套管材质有差异为好，并且膨胀管的屈服极限应小于套管的屈服极限，这样有利于保护套管。

Various cone spindles are available for use with the Wells-Brookfield Cone/Plate instruments.

各种不同的圆锥体纱锭可用来使用威尔斯-Brookfield 的圆锥体/碟子器具。

Versatility of Application ·The Wells-Brookfield Cone/Plate Viscometer provides a wide variety of shear rates and viscosity ranges, which can be further extended by the use of interchangeable cone spindles.

申请的多种变化·威尔斯-Brookfield 的圆锥体/碟子粘度计提供各式各样的修剪率和黏质范围，这可能是更进一步被可互换圆锥体纱锭的使用延长。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。