英语人>网络例句>concentration of 相关的网络例句
concentration of相关的网络例句

查询词典 concentration of

与 concentration of 相关的网络例句 [注:此内容来源于网络,仅供参考]

The reaction-diffusion model was developed to analyze the concentration of enantiomers and the separation factor of the enantioseparation process of chiral emulsion liquid membrane by studying the principle and some factors of mass transfer process. The mass transfer resistance of boundary layer in outer aqueous phase and the interfacial chemical reactions at the liquid membrane interfaces were taken into account in the model equations.

通过对乳状液膜手性分离过程中传质机理的研究以及各影响因素的分析,得到了可以分析和预测乳状液膜手性拆分过程传质的反应-扩散模型,该模型同时考虑了外水相边界层的扩散阻力和手性对映体与载体的反应阻力。

Glucose, formic acid and levulinic acid were not detected in the liquors of acid hydrolysis and the concentration of xylose and arabinose was high, while the acetic acid was low. The mixture of monosaccharides and fatty acid was efficiently separated and the whole process of separation was finished within 23 minutes.

通过对样品的分析表明,麦糟水解液中不含有葡萄糖、甲酸及乙酰丙酸,木糖和阿拉伯糖的质量浓度比较高,乙酸的质量浓度比较低,单糖及脂肪酸的混合液得到很好的分离,分离过程在23min内完成。

The results are as follows: 37℃ is the most favorable temperature for induction expression of SUMO-hEGF in BL21, 5.0g/L the most best concentration of arabinose, and 4h the best time for induction expression. Meanwhile, the quantity of expression is around 20.2%. The conclusion that hEGF is the purified protein is verified by Western blotting. It is a good foundation for the development of hEGF genetic medicine.

结果表明: SUMO-hEGF在BL21中的最佳诱导表达温度为37℃、诱导剂阿拉伯糖的最佳浓度为5.0g/L、最佳诱导表达时间为4h,表达量约为20.2%;Western blot 分析证实,纯化后的蛋白是hEGF,为进一步开发hEGF基因工程药物奠定了基础。

The viability of SAS cells decreased obviously because of the raised of the ANE and arecoline, especially in the concentration of 800 ug/ml and 0.8 mM respectively.

在细胞的存活性实验也发现,随著槟榔子萃取物与槟榔素浓度提高,分别在800 ug/ml与0.8 mM浓度时,SAS细胞存活率会有明显下降的情况。

Different DNA constructs were introduced into the decapsulated cysts of Artemia by electroporation under 2KV, 20 μsec pulse length, 20 number of pulses and a DNA concentration of 20μg/μl in a volume of 100μl.

不同的构筑质体经由电穿孔法,被导入经去壳处理后的丰年虾休眠卵中,在2千伏特、20微秒的脉冲波长度、20次的脉冲数和在100微升的体积中DNA浓度为每微升20微克的设定条件下。

Results The results showed that the average concentration of the bacteria, fungi and total microbes in the outdoor environment were 5.04×10^4, 3.75×10^3 and 5.41×10^4 cfu/m^3 respectively and the fungi accounted for 6.92% of the total. The preliminary identification showed that the dominant bacteria mainly were Micrococcus, Bacillus, Pseudomonas and Staphylococcus and the average percentage were 37.3%, 21.0%, 10.3% and 9.5% respectively. Of the five fungi the dominant ones were Aspergillum, Penicillium, Mucor and Rhizopu. The average percentage were 42.0%, 36.0%, 4.4% and 4.2% respectively. Conclusion The outdoor air of Hefei has been polluted by airborne microbes.

结果 合肥城区空气细菌总数均值为5.04×10^4cfu/立方公尺,真菌总数均值为3.75×10^3cfu/立方公尺,合计为5.41×10^4 cfu/立方公尺,其中真菌占6.92%;对不同采样点的空气细菌和真菌进行了初步鉴定,优势细菌属为微球菌属、芽孢杆菌属、假单胞菌属和葡萄球菌属,分别占总细菌的37.3%,21.0%,10.3%,9.5%;真菌共检出5属,其中优势菌属为曲霉属、青霉属、毛霉属、根霉属,分别占总真菌的42.0%,36.0 %,4.4%,4.2%。

Based on the theoretical calculation model for the structural information of metal melt, the main structural information, including relative concentration of active atoms, average diameter of the atomic clusters and the number of short-range atoms inside them, was achieved. Finally, by multiple non-linear fitting of experimental data, the function about viscosity and size of atomic clusters was established.

利用金属熔体结构信息的理论计算模型,得到该温度区间内铝熔体的主要结构信息,包括激活原子的相对浓度、原子集团的平均直径及其内部包含近程原子数等,最终通过实验数据的多次非线性拟合发现黏度与原子集团的尺寸之间存在函数关系。

With the development of science and technology, sensitive, rapid, reproducible, simple and accurate analytical methods are required for the determination of trace elements in geological, biological and environmental samples. The direct determination of extremely low concentration of trace element with modern atomic spectroscopic method, such as atomic absorption spectrometry is so difficult. On one hand, the limitations are associated not only with the insufficient sensitivity of these techniques but also with matrix interference.

随着科学技术技术的发展,在进行地质、环境、生物等样品中痕量金属元素的测定时,常常要求达到ppb级的水平,虽然火焰原子吸收分光光度法具有很高的灵敏度,但是要直接测定这些样品中的痕量组分却很难,这是因为,一方面,样品本身的物理化学状态有的不适合直接测定,或组分的含量低于分析方法的灵敏度;另一方面是存在基体干扰。

Numerical control lathe have following outstanding superiority than traditional lathe include:Can process out complicated parts, such as the curve coming out in traditional machine tooling, curved surface,etc;Because computer have superb operation ability is can instantaneous to calculate out each coordinate axis instantaneous amount of exercise that should move accurate, So can compound into the complicated curve or curved shttp://www.51lun-wen.cnurface ;Can realize automation that process is and flexible automation, so efficiency constant traditional lathe raises by 3-7 times;Because the computer has memory and stores ability ,Can carry out automatically according to the order that the procedure stipulates,so realize automation;Proceshttp://www.51lun-wen.cnng precision of part high, size disperse degree light, make and assemble easy, No longer need to" repair the damaged parts of a machine and supply replacements";Can realize the concentration of many processes,have many kinds of self-containment functions,such as autoalarm, controlling, automatic compensation automatically,etc;Therefore can realize that nobody guards and processes for a long time.

机床数控化改造可以加工出传统机床加工不出来的曲线、曲面等复杂的零件。数控机床比传统机床有以下突出的优越性,由于计算机可以瞬时准确地计算出每个坐标轴瞬时应该运动的运动量,因此可以复合成复杂的曲线或曲面;可以实现加工的自动化,而且是柔性自动化 http://www.51lun-wen.cn ,从而效率可比传统机床提高3~7倍;由于计算机有记忆和存储能力,可以将输入的程序记住和存储下来,然后按程序规定的顺序自动去执行;加工零件的精度高,尺寸分散度小,使装配容易,不再需要"修配";可实现多工序的集中,减少零件在机床间的频繁搬运;拥有自动报警、自动监控、自动补偿等多种自律功能,因而可实现长时间无人看管加工。

Numerical control lathe have following outstanding superiority than traditional lathe include:Can process out complicated parts, such as the curve coming out in traditional machine tooling, curved surface,etc;Because computer have superb operation ability is can instantaneous to calculate out each coordinate axis instantaneous amount of exercise that should move accurate, So can compound into the complicated curve or curved surface ;Can realize automation that process is and flexible automation, so efficiency constant traditional lathe raises by 3-7 times;Because the computer has memory and stores ability ,Can carry out automatically according to the order that the procedure stipulates,so realize automation;Processing precision of part high, size disperse degree light, make and assemble easy, No longer need to" repair the damaged parts of a machine and supply replacements";Can realize the concentration of many processes,have many kinds of self-containment functions,such as autoalarm, controlling, automatic compensation automatically,etc;Therefore can realize that nobody guards and processes for a long time.

机床数控化改造可以加工出传统机床加工不出来的曲线、曲面等复杂的零件。数控机床比传统机床有以下突出的优越性,由于计算机可以瞬时准确地计算出每个坐标轴瞬时应该运动的运动量,因此可以复合成复杂的曲线或曲面;可以实现加工的自动化,而且是柔性自动化,从而效率可比传统机床提高3~7倍;由于计算机有记忆和存储能力,可以将输入的程序记住和存储下来,然后按程序规定的顺序自动去执行;加工零件的精度高,尺寸分散度小,使装配容易,不再需要"修配";可实现多工序的集中,减少零件在机床间的频繁搬运;拥有自动报警、自动监控、自动补偿等多种自律功能,因而可实现长时间无人看管加工。

第52/100页 首页 < ... 48 49 50 51 52 53 54 55 56 ... > 尾页
推荐网络例句

She gently rebuff ed him, but agreed that they could be friends

她婉言拒绝了,但同意作为朋友相处。

If in the penal farm, you were sure to be criticized.

要是在劳改农场,你等着挨绳子吧!

Several theories about reigniting and extinguishing of the arc have been refered.

本文综合考虑了几种电弧重燃和熄灭理论。