查询词典 concave

Considering the triangulation algorithm based only on the determination of convex-concave vertices is restricted to simple polygons, this paper presents a triangulation algorithm for the general plane polygon GTP(General Triangulation of Polygons) based on determination of convex-concave vertices and connecting the outer border of a polygon with its inner borders.

摘 要：针对基于凹凸顶点判定的三角剖分算法适用范围有限的缺点，提出了将凹凸顶点判定与连接多边形内外边界相结合的适用任意平面多边形的三角剖分算法GTP(General Triangulation of Polygons)。

The crystal defect was observed and analyzed. Room temperature Nd:NYW crystal samples sized 3x3x5mm and 5x5x5mm were LD pumped at 808nm plane-concave cavity and double-concave cavity laser systems respectively, 1060-1064nm has been demonstrated.

室温下，分别用平一凹腔系统对尺寸为3×3×5mm的Nd：NYW激光晶体，用双凹腔系统对尺寸为5×5×5mm的Nd：NYW的激光晶体进行连续激光输出实验。

When the bottom plate side syndiospecific lower than a sizzling, drawing pressure ball left, paper will go on there which would in turn low-speed machines brace will receive the same fault because plate following fulcrun is the eccentric shaft, corrected, you can add the eccentric shaft, convex to reverse some of the panels to fan-shaped with a sizzling plane are equal to the maximum State, low-speed machines la along two concave iron support, you can set the concave iron spare, Planer to some, is equal to the thickness to brace the distance below the iron plate plane, the installation at a later time.

当侧规底部扇形不活矮于铁不活立体时，不推纸压球压下去此后，纸弛不离会出不隐凹下下去不隐象，矮速机的不推条也会出不隐同样的障碍，因为扇形不活底下的支点是公道小轴，在校侧时，可以不兵公道小轴的凸背回旋一些，调度到扇形不活背同铁不活立体不等为最好状况，矮速机的不推条是由二块凹形铁撑持，可以不兵凹形铁拆上去，用刨床刨去一些，刨去的厚度即是不推条矮于铁不活立体的间隔，安设此后再举不静调度。

Firstly, the mechanical analysis on the stability of deep-concave open pit slope based on the theory of elasticity has been presented, thus offering the probable cause theoretically for using the convex-form slope in the deep-concave open pit on one hand and the preliminary method to determine the rational shape of slope on the other hand.

首先，基于弹性理论对深凹露天矿边坡的稳定性做了力学分析，从而为凸形边坡在深凹露天矿的应用提供了理论依据，同时为确定合理的边坡形状提供了初步方法。

In this study, a commercial CAD/CAM Software is used to plan and generate the multi-axis tool path, and a table rotating/tilting type five-axis machining center is used to perform the experimental machining operation. The material of the die studied is NAK 80 die tool steel, and the geometries are modeled as concave and convex spherical surfaces. Milling parameters considered are spindle speed, feed rate, and different types of cutting tool path. The experimental results show that the surface roughness for concave spherical surface is about 0.247 μm and roundness is about 0.0283 mm and the surface roughness for convex spherical surface is about 0.250 μm and spherical roundness is about 0.0551 mm under the cutting conditions mentioned in this study.

本研究的实验方法与步骤包括利用商用CAD/CAM系统针对实验对象规划三轴/五轴同动加工路径，并经后处理程式转换，在本实验室之平台倾斜/旋转型之五轴加工机上进行实验，实验对象为NAK80模具钢材料之凹与凸球形曲面之加工，此外考虑的切削条件有主轴转速、进给速度、加工路径等，在本研究所设定之最佳切削条件下，凹球形曲面之真圆度约为0.0283 mm，粗糙度为0.247 μm，而在相同切削条件下，凸球形曲面之真圆度为0.0551 mm，粗糙度为0.250 μm。

The velocity,acceleration and time of a particle sliding down along a horizontally free concave surface are discussed.

对于一个质点从可自由移动的光滑的凹曲面上滑下的速度、加速度和时间作了一般性讨论，建立了相应的公式。

Flowers inserted on discoid or concave, fleshy receptacle; achene with crested or U-shaped appendix at apex.

花着生于盘状的或凹，肉质的花托；瘦果具脊或U形附属物在先端 7 Lecanthus 假楼梯草属

On the basis of B-Rep of CAD data and ACIS library,a technology of surface filling based on loop feature handling and outlines smoothing is presented in the paper,filling for the surface with complex concave edges is also studied in the paper.

以CAD数据的边界表示法和ACIS几何开发库为基础，提出了基于环特征处理和外边界光顺的曲面填充技术，对含有复杂凹缘的汽车覆盖件曲面填充进行了研究。

Anastigmatic mounts of concave gratings based on this algorithm are optimized,and numerical results are simulated.

基于此方法讨论了无象差点结构凹面光栅的优化设计，并给出了数值模拟结果。

Clinical manifestations, sinus large多斤called antihelix feet above the ostium diameter is only about 1mm concave hole can emit a little white micro-foul secretions.

临床表现，窦道大多斤吁耳轮脚前上方，窦口为直径仅1mm左右的凹孔，可排出少许白色微臭分泌物。

But your skeleton is as much a living part of your being as your softer tissues and organs.

但实际上你的骨架正像你的软组织和器官一样，是你生命个体的一个活着的部分。

Some known results are generalized.Second,the global asymptotic stability for a higher order rational difference equation was investigated by using "Subsequence Analysis Method " in Chapter 3,and the "Semi-cycle Analysis Method" is a extension and supplement of "Semi-cycle Analysis Method".

因此，本文第三章应用"子序列分析法"研究了一类高阶的有理差分方程解的全局动力行为，进一步得到了此类高阶有理差分程解得全局渐近稳定的一些充分条件，一些已知的结果被推广。