查询词典 concave slide

Among picosecond fluorescence spectroscopy setup, sample cell, one side is concave, and collimate optics system were designed and made. Which improve fluorescence collect rate 30%, and is key to experiment.

在荧光光谱装置中，设计制作了一侧为凹面的样品盒和准直光学系统，提高荧光的收集效率30%，对实验成功起了关键的作用。

Commissure face of seed deeply concave or sulcate.

果表面瘤状的或具小乳突。

The clip refers to the length and angle of the concave curve on the non-cutting portion of the point of the blade.

回形刀刃在刀尖的非切割部分采用的是凹曲线的长度和角度。

They are unevenly distributed along the retina, in the central retina and central macular area of about 3 □ concave angle exists only within the pyramidal cells.

它们沿着视网膜的分布是不均匀的，在视网膜中央的黄斑部位及中央凹大约3□视角范围内只存在着锥体细胞。

In this paper the natural boundary reduction for some elliptic boundary value problems with concave angle domains and its natural boundary element methods are investigated.

本文研究凹角型区域椭圆边值问题的自然边界归化及其边界元法。

Part II, the artificial boundary condition and its numerical methods based on natural boundary reduction for a hyperbolic initial boundary value problem in an infinite domain with a concave angle is investigated.

第二部分，研究一类具有凹角的无界外区域的双曲型初边值问题基于自然边界归化的人工边界条件及其数值方法。

Marc software, the two-dimensional simulation of isothermal extrusion forming process of globoidal cam was made. The influence of the different model cavity concave wedge angle a on the performance of filling billets was analyzed. It provided an important basis for the realization of cambered cam isothermal compression and the optimization of die structure.

用MSC。 Marc软件对弧面凸轮等温挤压成形过程进行了二维模拟，具体分析了不同凹模型腔楔角α对坯料填充性能的影响，为实现弧面凸轮等温挤压成形和优化模具结构提供了重要依据。

Based on the method of numerical simulation, the diameter of steel billet, entrance half angle of concave die and the dimension of spline were analyzed for the forming force on the spline processing with the help of a rigid-plasticity finite element software Deform 3D.

借助刚塑性有限元软件Deform-3D，采用数值模拟的方法分析了矩形花键轴冷挤压过程中，坯料直径、凹模入模半角及键齿尺寸对花键成形力的影响。

Aiming at plastic parts with oblique angle concave and convex stage,a novel die oblique core pulling bodies——slider mechanism with lifter body was put forward.

针对带有斜角度凹穴、凸台的塑料件，提出一种新颖的模具斜抽芯机构——"斜顶式"滑块机构。

Results indicate that when the strain rate is 1200 s-1, the twin number of samples in different orientation increases with plastic strain increasing; when the strain rate increases to 2800 s-1, the σ-ε curves have no obvious charges as the angle is 0o and 45o, compared with that at 1200 s-1; however the σ-ε curves vary from concave to convex when the angle is 90o, because thermal softening has occurred with increasing plastic strain, which results in the number of twin decreasing, and smaller strain hardening

结果表明：当加载应变率为1200 s-1时，不同取样方向的样品中孪晶数量均随塑性变形应变量的增大而增多；当加载应变率增大到为2800 s-1时，取样方向为0°和45°、流变曲线形状较应变率为1200 s-1时没有明显变化，而取样方向为90°时曲线形状由应变率为1200 s-1时的凹形变为凸形，曲线形状变化的原因是由于应变量增大，热软化效应使得孪

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48