查询词典 concave slide

The 4-inch Exe was always supplied with a proper compound slide rest (the various 3-inch versions made do with a single swivelling tool slide for many years) but for the first two years of production no graduated micrometer dials were fitted but, when introduced (simultaneously with that on the 33/8 lathe) was in the simple, effective and large-diameter form of an engraved wheel rim fitted to the cross-feed screw only.

4英寸的可执行总是提供适当的复合幻灯片休息（各3英寸版本取得与一个单一的旋转刀架多年），但前两年没有毕业微米生产转盘拟合但是，当介绍了（同时，在3 3/ 8车床）是在简单，有效和大直径形式刻装有车轮轮辋的跨饲料螺钉只。

Determine the correct exposure time is by using the exposure slide rule, this type of slide rule on the market.

猜测不差曝平工夫的办法是搁置曝平计算尺，这类计算尺可以在阛阓上当到。

Sometimes we have really long slide show but not every slide is important.

有时候，我们已经很长的幻灯片放映，但并不是每一个幻灯片是非常重要的。

Step 5: show a model slide this is a slide, what does it like?

第五步：幻灯片显示模式（这是一个幻灯片，它像什么？

So, I took a small hammer and dented the slide of the trombone enough so that it wouldn't slide (I guess I really wanted to play drums!).

所以，我拿了个小锤子敲我伸缩喇叭的伸缩端把它敲陷下去了这样就伸缩不起来了（我想我那时应该是想去打鼓吧～）。

First of all, the relationship between strain and pressure of slide valve membrane sensor under different loads was analyzed and simulated by using ANSYS software; then an experimental device was designed and used to calibrate the slide valve membrane sensor.

首先采用ANSYS软件模拟了阀瓣膜传感器承受不同载荷下的应变与压力的关系；同时也设计了一套阀瓣膜传感器的标定实验装置，利用该实验装置对阀瓣膜传感器进行了标定实验。

According to the characteristics and construction requirements, to develop the basis of elevation from the beginning of silo slipform construction used, sliding up to 4.3 meters above sea level, the reinforced air slide 5.15 meters; Party to begin construction within the building and the warehouse floor, after the completion of sliding mode Then slide up to 26 meters warehouse roof, sliding mode to remove.

根据工程特点及工期要求，拟定筒仓从基础标高开始采用滑模施工，滑升至标高4.3米时，加固空滑到5.15米；甲方开始施工仓内建筑及库底板，完工后滑模接着滑升至仓顶26米，滑模拆除。

Main job is to guarantee the scraping interaction and equipment on both sides of the friction surface or can obtain higher precision and accuracy, precision and shape accuracy, precision and contact transmission because of good lubrication, manual and repeatedly is worthy, large amounts of wind, time-consuming, scraping the time needed for different devices vary, such as boring slider and slide block wind profiling, between the match before measuring clearance between the original value, and then according to the technical requirement to measure the value of time and scraping scraping, then apply DanFen red on the slider, manual let slip on the slide seat back and forth, they do straight-line movement between full contact and friction, reoccupy scraper scraping friction creates the contact point, so repeatedly, until the technical requirements for the match, single within 2 days, must blow to the boring if all the time to work with wind, a half month is required.

刮削过程。刮削工作主要是为了保证设备相互接触并摩擦的两面间能获得较高的尺寸精度、形状精度、位置精度、接触精度、传动精度和良好的润滑，因是手工操作且需反复配刮，故工作量大，耗时较长，设备不同，刮削所需时间也各不相同，例如镗床上滑座与下滑座间的配刮，刮削前先测量出二者之间原有的间隙值，然后根据工艺要求测算出需刮削值及每次的刮削量，再将红丹粉涂于上滑座之上，手工让上滑座在下滑座上来回做直线运动，使它们之间充分接触和摩擦，再用刮刀刮削摩擦产生出的接触点，如此反复多次，直至技术要求范围之内，单此项配刮需2天左右，若对于整个镗床所有配刮工作的时间总和，则需半个月左右。

You can work with slides in the Slide Sorter view just as you can in the Slide pane.

在幻灯片浏览视图中，可以像在幻灯片窗格中一样，对幻灯片进行操作。

The same phenomena occurred with the distal end displacements when horizontally loaded: the largest was seen with the dovetail slide beyeler, followed sequentially by the Spang Stabilex, CCT, cylindrical slide, and the Mini SG.

结果显示各组之间虽然存在有许多统计意义差别，然而垂直施力时近心及远心的位移都很小(近心小於 3.0 micrometers，远心小於 21.4 micrometers)。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48