查询词典 concave line

They are unevenly distributed along the retina, in the central retina and central macular area of about 3 □ concave angle exists only within the pyramidal cells.

它们沿着视网膜的分布是不均匀的，在视网膜中央的黄斑部位及中央凹大约3□视角范围内只存在着锥体细胞。

In this paper the natural boundary reduction for some elliptic boundary value problems with concave angle domains and its natural boundary element methods are investigated.

本文研究凹角型区域椭圆边值问题的自然边界归化及其边界元法。

Part II, the artificial boundary condition and its numerical methods based on natural boundary reduction for a hyperbolic initial boundary value problem in an infinite domain with a concave angle is investigated.

第二部分，研究一类具有凹角的无界外区域的双曲型初边值问题基于自然边界归化的人工边界条件及其数值方法。

Marc software, the two-dimensional simulation of isothermal extrusion forming process of globoidal cam was made. The influence of the different model cavity concave wedge angle a on the performance of filling billets was analyzed. It provided an important basis for the realization of cambered cam isothermal compression and the optimization of die structure.

用MSC。 Marc软件对弧面凸轮等温挤压成形过程进行了二维模拟，具体分析了不同凹模型腔楔角α对坯料填充性能的影响，为实现弧面凸轮等温挤压成形和优化模具结构提供了重要依据。

Based on the method of numerical simulation, the diameter of steel billet, entrance half angle of concave die and the dimension of spline were analyzed for the forming force on the spline processing with the help of a rigid-plasticity finite element software Deform 3D.

借助刚塑性有限元软件Deform-3D，采用数值模拟的方法分析了矩形花键轴冷挤压过程中，坯料直径、凹模入模半角及键齿尺寸对花键成形力的影响。

Aiming at plastic parts with oblique angle concave and convex stage,a novel die oblique core pulling bodies——slider mechanism with lifter body was put forward.

针对带有斜角度凹穴、凸台的塑料件，提出一种新颖的模具斜抽芯机构——"斜顶式"滑块机构。

Results indicate that when the strain rate is 1200 s-1, the twin number of samples in different orientation increases with plastic strain increasing; when the strain rate increases to 2800 s-1, the σ-ε curves have no obvious charges as the angle is 0o and 45o, compared with that at 1200 s-1; however the σ-ε curves vary from concave to convex when the angle is 90o, because thermal softening has occurred with increasing plastic strain, which results in the number of twin decreasing, and smaller strain hardening

结果表明：当加载应变率为1200 s-1时，不同取样方向的样品中孪晶数量均随塑性变形应变量的增大而增多；当加载应变率增大到为2800 s-1时，取样方向为0°和45°、流变曲线形状较应变率为1200 s-1时没有明显变化，而取样方向为90°时曲线形状由应变率为1200 s-1时的凹形变为凸形，曲线形状变化的原因是由于应变量增大，热软化效应使得孪

With the corresponding flow parameters measured through the experiments and the criterion equation mentioned above,the correlation formula of degassing efficiency of flow of gas/liquid two-phase flow through corrugated multicup isoflux gas anchor is obtained through the regression analysis using the least square method and the Gaussian elimination.The influences of the number of arris and concave depth and angle on degassing efficiency are analyzed.

利用量纲分析方法建立了气液两相流体在瓦棱状多杯等流型气锚中流动的准则方程；根据室内实验测得相应参数和准则方程，利用最小二乘法及高斯消去法进行回归分析，得到气液两相流体在瓦棱状多杯等流型气锚中流动时脱气效率的关联公式，并分析了棱数、凹入深度、角度对脱气效率的影响。

The company has advanced mechanical equipment and strong technical force, capable of producing: 8-300mm range of straight profile, meta curved, staggered tooth shape, the overall level of tooth carbide saw blade milling cutter, cutter blade on three sides, convex semi-circular cutter, concave semicircle cutter, angle cutter, Slitter knives.

公司拥有先进的机械设备及雄厚的技术力量，能够生产：Φ8-300mm各种直齿形、元弧形、交错齿形、高低齿形整体硬质合金锯片铣刀、三面刃铣刀、凸半圆铣刀、凹半圆铣刀、角度铣刀、分条刀等。

Linear error curve can be concave curve, it could be a convex curve.

线性误差曲线可以是凹形曲线，也可以是凸形曲线。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48