查询词典 concave curve

Regularity is an important algebraic property of parametric curve and surface, which depends on the parameterization of parametric curve and surface.

正则性是参数曲线曲面的重要代数性质，是由参数曲线曲面的参数化决定的。

This paper first summarizes recent researches on this topic, and then proposes some methods for curve modeling with cubic algebraic curve based on pure geometric constraints that involve control points, tangent directions and curvatures.

然后提出了一种基于几何约束的三次代数曲线的插值方法，该方法完全通过几何量如控制顶点、切线和曲率来控制三次代数曲线的形状，使得对三次代数曲线的编辑与对三次 B-样条曲线的编辑一样灵活方便。

Applying multivariate spline theory which was established by Wang RenHong in ( [1] , [2] ), the Nother theorem of algebraic curve [71] is generalized to the piecewise algebraic curve.

1：利用王仁宏在文献（[1]，[2]）中关于多元样条函数的基本理论，本文将代数曲线的Nother定理（[71]）推广到分片代数曲线上，给出了剖分为〓，和星形剖分上的C〓分片Nother型定理。

It was found that the nonlinear current-voltage curve is the intrinsic property of WO〓 polycrystalline ceramic, and the curve is asymmetrical with very different behavior under applied direct and alternating voltage.

我们发现，非线性是WO〓多晶陶瓷的本征性质，伏安特性曲线是不对称的，而且交直流行为完全不同。

The spiral curve structure can be used in slow-wave systems. Theoretically an analytic description for spiral curve slow-wave systems can be achieved after much simplification and approximation.

螺旋线结构就可以作为慢波系统；理论上，经过很多的简化和近似，可以得到关于螺旋线慢波系统性能的解析描述。

Innovative automobile electronic ignition control system is based on the characteristic curve MAP of ignition advance angle to control data,and the insertion value algorithm and changing index exponent curve surface fitting algorithm are chosen dynamically.

新型汽车电子点火控制系统是以点火提前角的特性曲线MAP图为基础控制数据，动态选用插值算法和变阶曲面拟合算法。

Thus, the top curve and the lower curve correspond to the highest angle of attack, which is 14 deg.

因此，顶曲线和曲线下对应的最高攻角，这是14甘醇。

Curve functions of axial buccal crown and gingiva contour of each section were acquired by means of curve fitting, and the angle of emergence pofile was calculated, which represents the degree of undercut. Results There is unique relationship between axial crown and gingiva contour individually. This character of tooth is similar to its contralateral tooth.

结果 不同个体的牙冠轴面外形和牙龈外形有其特定的几何关系，同一断面的牙冠轴面外形曲线对应特定的牙龈外形曲线；同名牙同一断面的牙冠轴面外形之间及牙龈外形之间的重叠性很好。

Three cross-sections were made through crown and gingiva of the model tooth. Curve functions of axial buccal crown and gingiva contour of each section were acquired by means of curve fitting, and the angle of emergence pofile was calculated, which represents the degree of undercut.

以下颌第二前磨牙为研究对象，在牙列模型上通过牙冠部、牙龈作3个纵断面，用曲线拟和的方法得到每个断面的牙齿轴面外形及相应牙龈外形的曲线方程，以此分析两者之间的关系并计算牙冠起始外形角度，即倒凹程度的大小。

With the interpolation, resulting nearly arc length parameterized curve interpolatesa set of points of original curve.

最后，两个实例表明了近似弧长参数化曲线能很好地逼近原曲线，且没有所不希望的波动。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48