查询词典 composite testing

The method of testing the non combustibility of the composite material by using calorimeter is scientific and its determination conditions are rather safe and practical.

文章讨论了采用锥型量热计对复合材料的不燃性进行检验，方法科学，判定条件偏于安全，可操作性

A Uniformly Most Powerful Test is applied to the composite hypothesis testing of leak signal With little prior statistical knowledge.

给定误警概率和漏报概率，施行具有一致最大功效的似然比检验(Uniformly Most Powerful Test，UMPT)。

At present, the company has a modern feed production lines, advanced testing equipment, the country's quality management system and high-quality staff, technical standards, management methods to achieve the advanced level in the same industry, annual sales of products 10,000 tons, and its composite indicator Bureau with the industry the forefront.

现时，公司拥有现代化的饲料生产线，先进的产品检测设备，全国的质量管理体系和高素质的员工队伍，技术标准，管理方式达到同行业先进水平，年销售产品万吨，其综合指标局同行业前列。

In order to make best of efficiency of composite material in different conditions, testing of samples in distilled

其中水分环境是重要的因素之一，本文还针对T300/HT3进行了浸泡水后的疲劳性能试验，对水分对复合材料疲劳性能影响进行了初步的分析及研究。

The questing for acidic middle-temperature electroless Nickel technology leads to the preferable prescription as follows:Proportion of Nickel Sulphate and Sodium Hypophosphate 0.36; Sodium Acetate 15g/L; Stabilizer A lmg/L(Stabilizer B Img/L for continual experiment); Composite complexing agent Lactic Acid 10ml/L and acetic acid 10 ml/L; Accelerator organic acid G 6g/L; pH value 5.0; Loading Capacity ldm2/L; Temperature 70C (Temperature 75C for continual experiment); Proportion of supplement for Nickel Sulphate and Sodium Hypophosphate 1:1.2; Testing the consumed ion of Nickel solution and supplement inspissations solution every 60min by the proportion of 15% fresh solution.

最后，通过研究得出最佳工艺配方为：硫酸镍与次亚磷酸钠的摩尔比为0.36；乙酸钠15g／L：稳定剂Almg／L(周期实验加稳定剂B10mg／L)；复合络合剂组合为乳酸10ml／L+冰乙酸10ml／L：促进剂为有机酸G6g／L；pH值为5.0；装载量为1.0dm~2／L；施镀温度为70℃(周期实验为75℃)：主盐与还原剂的添加比例1：1.2；每60分钟对镀后液进行镍离子浓度的测定并按镍离子的消耗量添加浓缩液，添加比例按开缸液的15％。

Electronic equipment categories: two core, three core insulated wire conduction test machine, an integrated plug-line tester, polarity tester, full-featured integrated precision wire tester, analog / digital storage oscilloscope, signal generator, the standard signal source, frequency dollars, Millivoltmeter distortion device,Miriam, LCR digital electric bridge, voltage tester, insulation resistance tester, grounding resistance tester, leakage current tester, electronic load, electric parameter measuring instrument, digital power meter, parameter measuring instrument transformers, transformer automatic testing system, transformers ring than phase tester, electrical safety parameter tester, variable frequency power supply, power supply, high-frequency shielding net room, temperature and humidity table, multimeter, power meter, tachometer, anemometer, coating thickness, coating thickness, vibration measuring instrument, the Composite test machines (motors, fans, hair dryer, lamps, fruit juice machine) and so on.

二芯、三芯线材绝缘导通测试机、插头线综合测试机、极性测试仪、全功能精密线材综合测试机、模拟/数字存储示波器、信号发生器、标准信号源、频率计、毫伏表、失真仪、抖晃仪、LCR数字电桥、耐压测试仪、绝缘电阻测试仪、接地电阻测试仪、泄漏电流测试仪、电子负载、电参数测量仪、数字功率计、变压器参数测量仪、变压器自动测试系统、变压器圈数比相位测试器、电器安全参数综合测试仪、变频电源、电源供应器、高频屏蔽网房、温湿度表、万用表、功率表、转速表、风速计、涂层测厚仪、镀层测厚仪、振动测量仪、综合测试机（马达、风扇、电吹风、灯饰、果汁机）等。

According to the characteristics of collapsible loess ground and the practice of multistoried engineering,the designing and testing of earth pile composite ground is introduced and the advantages of earth pile in treating thicker collapsible loess ground in multistoried engineering is proved.

针对湿陷性黄土地基的特点，结合多层建筑的工程实际情况，介绍了土挤密桩复合地基的设计和检测工作，阐述了土挤密桩在多层建筑中处理厚度较大的湿陷性黄土地基的优势。

Ultramicrohardness testing was employed to measure the hardness of the matrix in a hotextruded SiCp/LD2 composite for characterizing the law of distribution of thermal residual strain in the matrix.

用超显微硬度仪测试了热挤出态的SiCp/LD2复合材料中基体微区的硬度，用于表征材料基体中的热残余应变分布规律。

Based on the previous viewpoints and the testing project of Shanghai Metro, the research on the theory and design method of the secant pile wall composite structure used as permanent structure is studied in the paper.

基于这样的观点，本文结合上海地铁某咬合桩试验段工程，对咬合桩作为永久结构使用的咬合桩复合结构设计理论和方法进行了研究。

Ultrasonic testing using the through transmission squirter technique remains the predominant method of inspection of composite materials.

超声波探伤法用的是穿透传输喷水技术也是复合材料检测的主要方法。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。