查询词典 compensation of error

It also discusses the effect upon the dynamic performance of this gyrostabilizer system when the gyro error compensation has been complted.

本文紧密结合工程实践，详细讨论了在陀螺稳定系统中通常所采用的两种不同的陀螺仪误差模型，并实施误差补偿之后，对陀螺稳定系统动态性能的影响，同时给出了仿真结果。

In order to solve the problem mentioned above, a new dynamic compensation method using linear extrapolation scheme was presented to compensate the measured output of inductorsyn. Thus the measuring error induced by measuring delay was reduced, and the system tracking precision was enhanced.

为解决上述问题，提出一种动态补偿方法，采用线性外推方法，对圆感应同步器数显表的测量输出进行动态修正，以减小由于测量延迟产生的测量误差，从而提高系统的动态跟踪精度。

Error compensation is the economic and effective way to improve the accuracy of Coordinate Measuring Machine.

误差补偿是提高三坐标测量机整体精度的经济而有效的手段，本文利用精度等级更高的激光干涉仪对三坐标测量机的X轴直线度误差进行了测量，并得出了初步结论，为以后进行误差补偿提供了依据。

The research team have ever fabricated the thin-film of ther mocouples by Multiple Arc Ion plating, and the contributions of the film are deviating from the target, so the Seebeck coeffcient is not in accordance with the normal thermocouples composed of Ni-Cr/Ni-Si wires, which lead to the larger error when Ni-Cr/Ni-Si wires was applied to the cuting test as compensation lead.

本课题组曾采用多弧离子镀方法制备Ni-Cr/Ni-Si薄膜热电偶，由于薄膜成分偏离标准大块Ni-Cr/Ni-Si材料，导致热电偶塞贝克系数与标准Ni-Cr/Ni-Si丝式热电偶相差较大。

This paper focuses on a development of a sensor system measuring heading of a vehicle or plane. The theory of the solid-state magnetic sensor is presented. It also will include the numerical calculation and error compensation.

依据所实现的一种测量航向角的新方法，论述磁阻传感器的原理，给出了系统数值计算方法，分析了系统误差并进行校正。

The error compensation is introduced in the interpolation algorithm to increase the interpolation point's solution precision in the cutting direction of the parametric curved surface. The reasonable simplification of the computed result of the interpolation point's parameter value is carried in the operation process by focusing on the character that curvature of slow-varying parametric curved surface changed slowly and the feature that the scanned profile of translational scanned curved surface is parallel along the scanned line.

通过引入误差补偿值以提高参数曲面在走刀方向上插补点的计算精度，针对缓变参数曲面曲率缓变和平移扫描曲面扫描轮廓沿扫描线平行的特点在运算过程中对插补点参数值的计算结果进行合理简化。

A control method of synchronously material downloading and periodic error compensation is adopted in the material blending system to improve the precision of the material blending procedure.

在微机配料系统中采用了同步下料、周期补差的控制方法，提高了水泥配料的精确性。

In order to reduce the periodic current tracking error of the deadbeat control when compensating abruptly changing nonlinear load current, a repetitive controller is plugged into the deadbeat controller. Also, the repetitive controller can alleviate the parametric dependency of the deadbeat control and eliminate the effects on compensation performance caused by the uncertainties in the system.

另外，为了降低无差拍控制对系统参数的依赖型和系统中存在的不确定性对补偿性能的影响以及减小在补偿电流变化剧烈的非线性负载电流过程中存在的周期性的局部跟踪误差，本文在无差拍控制器的基础上，又提出了基于无差拍和重复控制的复合电流控制器。

Different polynomial coefficient combination of amplitude changes is selected as the input signal to minimize the compensation error. A dynamic coefficient polynomial model is given with simplified coefficient estimation algorithm based on direct learning architecture.

动态系数多项式具有多组系数，随着输入信号幅度的变化，多项式选取不同的系数组合，从而降低非线性补偿的误差；文中讨论了动态系数多项式模型的构造方法，并且给出了基于直接学习结构的简化递归系数估计算法。

Error compensation is an economical and feasible method to enhance the precision of the machine tool.

误差补偿是提高设备加工精度经济合理又可行的方法。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。