查询词典 compensate

Aiming at these factors,our main ameliorative measures are:as following:adopting " three-high rates " composition,in a specific way,three rates should choose KH:0.88-0.92,SM:2.6-2.8,IM:1.6-1.8,and controlling the content of R2O,SO3,this method can insure that the content of silicate mineral is higher than 77%,especially the content of C3S is lower than 55%,so it can compensate for insufficient of descending of cement strength resulted by inactive component after implementing the checking method of ISO cement strength.

针对这些因素的主要改进措施为：采用&三高&配方，即三率值宜选择为KH0.88～0.92、SM2.6～2.8、IM1.6～1.8，并控制好R_2O、SO_3含量，以此保证水泥中的活性组分即硅酸盐矿物的含量≥77％，特别是C_3S含量不能低于55％，这样就能弥补因实施ISO强度检验方法后，水泥中非活性组分导致强度下降的不足。

Then, to compensate dispersion of a signal with bandwidth of 0.2 nm and center wavelength of 1550 nm, the thin-clad chirped LPFG with appropriate parameters is designed.

然后利用上述方法设计了对光纤中传输的中心波长为1550 nm，带宽为0.2 nm的信号进行色散补偿的薄包层啁啾LPFG。

Based on coupled-mode theory and transfer matrix, numerical results show that about 1 m of such thin-clad chirped LPFG can compensate 46 km fiber's dispersion.

利用耦合模理论及传输矩阵法计算了约1 m长的此种啁啾LPFG的色散，结果表明可以补偿该光信号通过46 km光纤所产生的色散。

Dancer roller: A wrighter or spring-loaded roller in contact with the web to compensate for uneven tension, Also called Tension roller, Idler, Jockey orll.

张力辘：用弹簧或砝码拉紧的辘。它与纸卷接触，以抵消纸上的不均匀张力。亦称辘，骑辘。

Then, based on the consideration of decreasing impact force by correcting the robot swing foot motion error, develop a fuzzy compensate control strategy for swing foot landing. The motion control commands of pitch DOFs of hip joint, knee joint, and ankle joint of swing leg are gradually compensated online.

并基于调整机器人摆动脚运动误差以减小步行碰撞力的减振思路，提出了摆动脚落地补偿控制策略，在线分级实时补偿摆动腿的髋前摆、膝前摆和踝前摆的运动角度。

Afterwards, we have fulfilled motion analysis based on the vasuclar models which we have already built. We have brought forward some new ideas in motion analysis, thus designed and completed String Matching Method and Thin Plate Spline Model based Method. Further, we have invented a mixed model which combined feature based model and intensity based model together, so as to compensate both disadvantages.

我们提出了一些运动分析方面的新思路，设计并完成基于链码匹配技术的运动分析、基于薄型样条模型的运动分析，我们还提出了一种结合基于特征模型和基于灰度模型的混合模型进行运动分析，弥补了各自长期以来的缺陷。

Apart from the working limitations resulting from its structural property, the flat plate heat pipe carries out heat dissipation through the evaporation and condensation of the working fluid. Thus, if the working angle of the fluid is adverse to its backflow, the heat pipe will fail easily. Furthermore, not the orientations of all the heat sources are favorable to the functioning of the heat pipe. To compensate for this drawback, this research focuses primarily on the development of a composite structure which will reduce the effect of gravity on the working fluid. Generally speaking, the heat pipe is divided into three main categories: the groove type, sintered metal type and mesh screen type, as shown in Table 2. As far as capillary force is concerned, the sintered metal type and mesh screen type show better performance. As mentioned in R.

平板式热管除了因其结构特性而产生的工作极限之外，由于其作用乃是透过工作流体的蒸发及凝结进行散热，故若是其工作角度不利于液体之回流，便容易使热管失效，且并非所有之发热源都是位于有利于热管工作之位置，因此本研究之主要目的为设计一可减少重力对工作流体影响之复合式结构；一般而言，热管之结构大致可分为沟槽、烧结及网格三种(如表2所示)，其中烧结及网格结构有较佳之毛细力，在 R。

The calibration approach can compensate at certain degree for the robot absolute location error in local space, and the gross measure accuracy of the vision system can meet the demand for off-line programming.

此标定方法在局部空间可在一定程度上补偿机器人的绝对定位误差，标定后的视觉系统综合测量精度满足离线编程的需要。

In the auto-body assembly process, the sound joint configuration would reduce and/or eliminate assembly variation propagation between parts, because rational allocation and design of joint configuration enable to adjust assembly process locators to achieve slip joint absorb or compensate the variation accumulation to improve the assembly robustness, therefore, the paper study joint type design and configuration and describe a multi-station auto-body assembly propagation model.

在车身装配过程中，良好的接头设计可以减小甚至消除零部件间的装配公差的传播，而且合理的接头配置方案有助于装配偏差的减小与装配过程的稳定性，因此论文详细分析了接头类型设计与接头配置，并介绍了多站点车身装配偏差传播模型。

The two wide used topologies of the main circuit of shunt active power filter which has the ability to compensate the neutral current are the three-leg split-capacitor topology and the four-leg topology.

具有中线电流补偿能力的并联有源电力滤波器主电路拓扑结构主要是三桥臂电容中分和四桥臂两种。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。