查询词典 combustion

By the comparison and analysis of the ionic current under different bias voltage between the long-straight tubular combustion device and the engine, it's also found that in the propagating flame front region and postflame region, with the increase of bias voltage the force of electric field will increase and the electrization action will be enhanced, which will enlarge the ionic current.

建立的离子电流随偏置电压变化关系的数学模型与实际燃烧过程是相符的，同时还可得到在两个实验中离子电流第一峰和第二峰的峰值随偏置电压变化关系基本都是线性的。

The feasibility of the SHS reaction was determined consequently, the combustion products and the solidification process of molten Cu and Cr were analyzed and calculated elementally.

通过对CuO-Cr2O3-Al反应体系的绝热温度计算及热力学分析，确定该体系自蔓延反应进行的可行性，并对反应后液态金属Cu和金属Cr的冷凝过程进行了初步的分析与计算。

We study the Emulsification Stability and the combustion characteristics of the droplets.

实验中第一部分先测试各种比例的柴油、水和醇类的乳化液是否能达到短暂稳定，甚至是更长时间的稳定。

This paper described such a comprehensive model based on a great number of documents, which takes into consideration details including air entrainment of fuel liquid zones, unsteady heat transfer during droplet evaporation, difference between premixed and entrain dominant combustion rate, compression factor of actual gas in cylinder pressure calculation and minimization of free energy during chemical equilibrium.

摘 要：对增压直喷柴油机的缸内空气卷吸、瞬态燃油液滴蒸发、燃烧过程的分段特征、化学反应平衡的最小自由能机理、实际气体性质修正、燃烧排放物生成等进行了分析，结合缸外的喷油过程仿真及进排气过程的容积法，建立了一个综合的研究性能及排放的准维多区模型，并进行了两个机型多个工况的实机试验比较。

The size and velocity of the droplets change continuously during their entrainment and acceleration in the hot gas combustion flow.

大小和速度的液滴不断变化的期间，夹带和加速度在炎热的气体燃烧流。

The effect of switching modes on the entrancement,combustion and billet heating process in furnace were analyzed numerically,and the computational results were compared with production records and onsite measurement,which verified the practicability of this CFD system.

结果表明：采用分段同侧换向控制的HTAC加热炉能获得很好的流场和温度场分布，基本满足高质量的钢坯加热需要，但该炉在生产条件下的温度制度存在不合理之处，在今后设计和操作中应进一步优化和改进；全同侧换向控制的火焰布置方式不利于钢坯的均匀、快速加热；而采用交叉换向控制的火焰布置方式可以改善加热炉内的流场和温度分布，更有利于满足钢坯的加热工艺要求。

Then the basic fundamental and method of the computation of thermal load of the heated parts of internal-combustion engine are elaborated, the deflective differential equation of heat conduction, basic equation and boundary condition of the theory of thermo elasticity and numerical computation by FEA are introduced.

接着阐述了求解内燃机受热零部件热负荷的基本原理和方法，介绍了热传导的偏微分方程、热弹性理论的基本方程和边界条件确定的原则以及用有限元法进行的数值求解。

The anti-jamming ability of igniter depends on the charge in the igniter. The combustion of the igniter charged with barium nitrate and those charged with magnesium powder and PTFE is stable, while the igniter charged with zirconium hydride and lead oxide is unstable. The standard error of duration of the third kind of igniter flame is 523 ms ,and also its nozzle hole is blocked seriously.

不同药剂的点火具抗干扰性能不同，其中以硝酸钡为药剂主成分的点火具和以镁粉＋PTFE为药剂主成分的点火具燃烧性能稳定，以氢化锆、二氧化铅为药剂主成分的点火具工作稳定性较差，火焰持续时间标准差为523 ms，点火具喷孔堵塞严重。

Heat release rate is the most essential parameter for combustion process, and is often employed to study the dynamic suppression process of a pool fire under water mist application.

热释放速率是燃烧过程最基本的特性参数之一，在研究细水雾与油池火相互作用时可以用来表示其动态发展过程。

Heat release rate is the most essential parameter for combustion process,and often employed to study the dunamic supression process of a pool fire under water mist application.

热释放速率是燃烧过程最基本的特性参数之一，在研究细水雾与油池火相互作用时可以用来表示其动态发展过程。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。