查询词典 combustion tube

Suggestions on tube replacement and combustion adjustment were proposed.

介绍了吴泾热电厂11号锅炉冷灰斗斜面水冷壁管减薄损伤情况，分析了管壁损伤的原因，提出了相应的管子更换和燃烧调整试验建议。

High temperature air combustion ; fired-gas radiant tube combustor ; application

高温空气燃烧；燃气辐射管燃烧器；应用

And the results of T-burner experiment show the residues on the tube wall of combustion chamber and percentage of large particles decrease significantly because of using the coated aluminum particles in the solid propellant.

激光点火实验初步验证了这种设想的可行性。T形燃烧器的实验结果表明，使用包覆铝粉的推进剂，燃烧室管壁残存的残渣量和残渣中大粒子所占的百分数显著减少。

Design and selection of combustion chamber,inlet tube and injector in ZG190 model direct injection are introduced in this paper and optimum performance parameters of ZG190 model diesel engine are determined by experiments.

介绍ZG190型直喷式柴油机的燃烧室、进气道、喷油器等设计及选择，通过试验通定ZG190型柴油机的最佳性能参数。

In first section, the mass size distribution, physicochemical characteristics and formation mechanism of the SPM from pulverized coal combustion in a drop tube furnace were discussed. Factors that influencing the emission characteristics and elemental partition of the SPM were also investigated, which included the distribution of furnace temperature, coal particle size and oxygen concentration.

本文首先在实验室的沉降炉上对六盘水烟煤、平顶山烟煤和合山烟煤分别进行燃烧实验，通过对燃烧生成的颗粒物收集后进行XRF、SEM、SEM-EDX等分析，研究了颗粒物的质量粒径分布、物理化学特征及亚微米颗粒的形成机理。

The whole geometric structures of combustor,combustion chamber and furnace tube in delayed coking furnace were accurately calculated by the whole-coupling method.

采用分区耦合的计算方法，实现了对工业焦化炉从燃烧器、炉膛、炉管整体几何结构的仿真，并且对焦化炉内流动、燃烧和传热全部工艺过程进行了模拟。

Keywords dust explosion;aluminum dust;combustion;detonation;detonation tube

粉尘爆炸；铝粉；燃烧；爆轰；爆轰管

Close to the compressor impeller end of the sealing ring or rejection damaged oil ring, oil will enter the impeller chamber, and then later with the indoor air with pressurized by entering into the combustion chamber of the tube.

靠近压气叶轮一端的密封环或甩油环损坏后，机油由此进入叶轮室，然后随室内增压后的空气一同经进所管进入燃烧室。

Combining the characteristics of furnace with doughnut-shaped steel pipe this article gives us the introduction that by using the fuzzy PID technology, simulate technology of computer, communication technology of network and spot bus technology and adopting Siemens S7-300 and Wincc software can realize the automation control of furnace's temperature to reduce energy consumption and cut down combustion of base tube.

本文结合钢管环形加热炉的特点，运用模糊PID技术、计算机仿真技术、网络通讯技术、现场总线等技术，采用西门子S7-300PLC和西门子WinCC上位机软件，以降低能耗和减少管坯烧损为目的实现环形加热炉的炉温自动化控制。

Combined with new tendency and practice in internal combustion engine industry at home and abroad in recent years,this paper suggests that machining cone of intake and exhaust valve seat insert and guide tube hole is the key technique in machining complicated cylider-head.

结合近年来国内外内燃机行业发展的新趋势和工作实践，对结构复杂的气缸盖机械加工提出了进、排气门座圈锥面与导管孔的加工是其工艺技术关键，从定位方式、基准选择、气门座底孔与导管孔底孔的加工，气门座圈锥面加工方式和导管孔的加工方式等方面进行了探讨和分析。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。