查询词典 column cap

The load transfer and settlement behavior from the simulation results are also analyzed: most of the column load concentrates on the enlarged column cap, and distributes quickly, there is more load attenuation at the variable section. The skin friction of enlarged column cap develops more adequately than underside column. The column settlement concentrates on enlarged column cap, and soil settlement concentrates on a little area below the variable section.

利用三维数值模拟分析了钉形搅拌桩复合地基的荷载传递和变形特性：钉形搅拌桩桩身荷载主要集中在扩大头部分，且衰减较快，变截面处桩身轴力有较大衰减，扩大头桩侧摩阻力较大，下部桩体侧摩阻力较小；桩身变形集中在扩大头，桩间土变形则集中在变截面以下较短范围内。

Among them flowers and plants of head shape column (flowers and plants of column of Capitata), horse segment of a circle (flowers and plants of column of Fine Stem), Mineirao and CIAT1517 column flowers and plants (CIAT1517) belongs to phosphor small effect is not sensitive model; heat grinds 2 column flowers and plants (Reyan2), heat grinds 5 column flowers and plants (Reyan5), flowers and plants of column having a check mark (flowers and plants of column of Verano), bush and TPRC2001-2 column flowers and plants (TPRC2001-2) performance is not steady.

其中头状柱花草、马弓形柱花草、Mineirao柱花草和CIAT1517柱花草(CIAT1517)属于磷低效不敏感型；热研2号柱花草(Reyan2)、热研5号柱花草(Reyan5)、GC1581柱花草(GC1581)和TPRC2001-1柱花草(TPRC2001-1)属于磷高效敏感型；西卡柱花草属于磷高效不敏感型，有钩柱花草、灌木柱花草和TPRC2001-2柱花草(TPRC2001-2)表现不稳定。

The main research contents are as follows:1. Through massive calculation, analysis and comparison, sum up the similarities and differences between the special-shaped cross sections and rectangular cross sections in mechanical features, between reinforced concrete special-shaped columns and rectangular columns in load-bearing capacity, ductility performance and provide necessary basic concepts and data for further understanding the characteristics of the special-shaped columns;2. Through massive elastic calculations and elasto-plastic analysis, under the preconditions of satisfying the code's requirements for axial compression ratio, limit value of lateral displacement and load-bearing capacity of normal section,oblique section and beam-column joint, under circumstances of different intensity of earthquake, structure dead weight, sort of site and column grid bay dimension, the variation regularity of maximum suitable height of structure, and thus sum up the maximum suitable height of structure for code for the purpose of macro-control while deciding the design scheme;3. Make a preliminary study on the stress feature of reinforced concrete special-shaped column and Z-shaped column of which the ratio of limb length to limb thickness is between 4~5 ,and the preliminary design method is suggested;4. Through elato-plastic time history dynamic analysis of typical projects, check up the weak storey of the special-shaped column structure and yielding, breaking and collapse mechanism to satisfy the earthquake resistant requirement to buildings of remaining stand under strong earthquake;5. Derive for project use simplified calculation formula of vibration period, suitable vibration period, suitable rigidity of special-shaped column structure through theoretical analysis, and provide an easy and practical method for deciding the structure scheme economically, safely and reasonably;6. Based on the study achievements in theory and massive analysis and calculations of this paper, sum up the regularities of inner force, deformation of special-shaped column structure and seismic conceptual design, and thus the suggection of seismic design of special-shaped column structures is presented.

本文研究的主要内容如下：通过大量的计算、分析和对比，总结出异形截面与矩形截面在力学特性、钢筋混凝土异形截面柱与矩形截面柱在承载能力、延性性能等方面的异同，为深入了解异形截面柱的特点提供必要的基本概念和数据；通过大量的弹性及弹塑性计算分析，在满足规程对轴压比、侧移限值及正截面、斜截面、节点承载力抗震验算要求的前提下，在不同抗震设防烈度、结构自重、场地类别及柱网开间尺寸情况下最大适宜高度的变化规律，并在此基础上总结归纳出异形柱结构的最大适用高度规定，可用于规程，以便于在确定方案时起到宏观控制的作用；对肢长与肢厚比在4～5的钢筋混凝土异形截面柱及Z形柱的受力特点进行初步探讨，提出初步的设计方法；通过对典型工程的弹塑性动力时程分析，检验异形柱结构的薄弱层及屈服、破坏、倒塌机制，以达到建筑物大震不倒的抗震设防要求；通过理论分析，推导出异形柱结构自振周期，以及适宜自振周期、适宜刚度的工程实用简化计算公式，为经济、安全、合理地确定结构方案提供简便实用的方法；在本文理论分析、计算以及大量的研究成果基础上，总结归纳出异形柱结构内力、变形的规律及抗震概念设计内容，并在此基础上提出异形柱结构的抗震设计建议。

When the gas reserves of the gas cap are relatively bigger, the gas cap and the oil column should be exploited simultaneously. When the volume of the gas cap is relatively smaller and the energy of the edge and bottom water is sufficient, the oil column should be exploited first depending on the natural energy, then water injection should be done artificially, and the gas cap should be exploited at last.

当气顶气储量相对较大时，采取气顶、油区同时开发；而对于气顶体积相对较小并且边、底水能量充足时，采取先依靠天然能量开采油区，然后人工注水，最后开采气顶。

The conclusions were as follows: theνO-H andνC=O IR absorption maxima shifted towards higher wave numbers after imprinting 17β-estradiol on TFMAA-co-TRIM copolymer with the red shift of theνO-H groups being apparent after precipitation polymerization for 16h while that forνC=O groups being observed after polymerization for 24h. A strong interaction between TFMAA and 17β-estradiol was confirmed by the high selectivity for 17β-estradiol, as indicted by the values of the separation factor of isomers of 17β-estradiol/17α-estradiol (2.28) and the imprinted factor (3.01). Particle diameter of TFMAA-co-TRIM polymer was between 300 nm and 1.5μm, which suited well for solid phase sorbent throughout at low column pressure. The recognition of imprinting TFMAA-co-TRIM polymer for sterol molecules was driven by enthalpy eluted with acetronitile, and low temperature was in favor of the separation of sterol structure analogues on imprinting column. TFMAA-co-TRIM polymer possessed of determinate anti-heat stability, with melting point beginning at 255.84℃, Tp=257.40℃, control TFMAA-co-TRIM polymer and imprinting TFMAA-co-TRIM polymer were respectively decompounded at 267.79℃and 343.11℃, and solid micro-extraction noddle prepared by the special polymerization also showed definite recognition for 17β-estradiol by GC/MS detecting at 270℃. By selection of various washing and elution solvents, elution reagents of close polymerization system were of more advantage in template molecules retention and recognition on molecularly imprinted solid phase extraction column. At a certain extent, progesterone, 17α-estradiol, 17β-estradiol and 4-androstene-3, 17-dione could be intercepted on the MISPE column. Especially, MISPE had high selectivity for progesterone, and imprinting TFMAA-co-TRIM polymer could achieve adsorption balance within 50 min by absorption kinetics test for 17β-estradiol. However, MISPE column showed better selectivity and enrichment property for 17β-estradiol than C18 and CSPE columns according to the data from HPLC and GC/MS analyses. Recovery of 17β-estradiol on MISPE column was up to 85.5% while when prime extracting solution of milk powder was sampled, the recovery of CSPE and C18 columns were 43.7% and 30.7%, respectively.

通过研究阐明：紫外聚合产物TFMAA-co-TRIM中的νO-H振动吸收峰在聚合16h后红移，νC=O振动吸收峰在聚合24h后红移；TFMAA-co-TRIM对雌二醇异构体的印迹因子达到了3.01，α为2.28，优于其它功能单体参与得到的聚合物识别特性；TFMAA-co-TRIM聚合物粒径介于300 nm至1.5μm之间，作为色谱固定相具有良好的通量和低的柱压；在乙腈流动相中，TFMAA-co-TRIM分子印迹固定相的分离过程主要被焓驱动，低温有利于分子印迹固定相分离甾醇结构类似物；TFMAA-co-TRIM分子印迹聚合物在255.84℃时开始熔融，Tp=257.40℃，聚合物CP的降解温度在267.79℃，MIP降解温度在343.11℃，制备的固相微萃取头初步经GC/MS 270℃的耐热性测定；不同的洗提溶剂筛选证明了选择接近聚合溶剂的洗脱体系更有利于MISPE发挥识别效应；分子印迹固相萃取柱对孕酮、17α-雌二醇、17β-雌二醇和雄烯二酮都具有不同程度的保留特性，可作为此类化合物的吸附材料，特别对孕酮强保留的富集特性，可作为孕酮的选择性识别吸附剂，其分子印迹聚合物对17β-雌二醇的吸附动力学测定显示在50 min内基本达到吸附平衡，具有作为传感器核心敏感材料的潜力；对比萃取奶粉中17β-雌二醇性能，MISPE柱比非分子印迹固相萃取柱和C18柱具有更高的保留，回收率依次为85.5%，43.7%和30.7%。

Based on the load transmission mechanism of space truss, and referenced theanalysis of test materials, a formula for calculating the bearing capacity of reinforcedconcrete compression strut is introduced. By using the theory of plastic hinge-line, anupper limit solution of bent bearing capacity for four-pile cap, which coincidesprecisely with the practical measurements, is obtained. By utilizing the reaction ofthe soil under cap and by basing on the method of plastic ultimate analysis, an upperlimit solution of punching shear bearing capacity for pile cap is acquired, which. coincides precisely with the practical measurements, and the formula is similar to thecode.A brief discuss on cooperative work of strip beam of foundation and single rankof piles is made. Separately considering the pile-cap and the pile-group, thencoupling their matrix of rigidity, the inner force of pile-cap is solved by the numericalmethod under some reasonable supposition. In comparison with other method, thecalculating results are exact, reliable and convenient in using. The method provides apowerful tQol fOr further analysis and research on this kind of structure.

本文以空间桁架传力机理为基础，结合试验资料分析，推导了钢筋混凝土等边三桩承台受冲切承载力计算公式；根据塑性铰线理论，导得了与试验结果吻合良好的四桩承台受弯承载力的上限解；利用承台底土反力分布，根据塑性极限分析方法，导得了桩基承台受冲切承载力的上限解，在此基础上，通过简化假定，得到与规范公式相类似的承台受冲切承载力实用公式，该公式能方便考虑台底土反力作用，与试验结果的吻合程度比规范公式好；简要讨论了桩基条形承台梁与单排桩的协同工作分析；在一些合理假定的基础上，将承台与群桩分开考虑，分别得到其刚度矩阵后进行耦合，通过数值方法求解承台内力，算例表明，该方法结果准确，使用方便，为该类结构的进一步分析研究及工程设计提供了强有力的工具。

Our factory covers an area of over 2000 square meters. With technically advanced production equipment, strong technical force, and modernized management system, the company mainly produces series of Bag and hats, Sports cap, Baseball cap, Bucket hat, Sun visor, Mesh cap, Knitted hat, Scarf,Washed cap, Children cap, and so on. The materials include gauze, dacron drill, fluff canvas, corduroy and coarse cotton cloth leather, etc.

我们工厂占地面积1500余平方米，拥有先进的生产设备，雄厚的技术力量，现代化的管理体系，主要生产箱包各种礼帽、定型帽、毡帽、运动帽、棒球帽、渔夫帽、太阳帽、网帽、针织帽、水洗帽、儿童帽等系列产品，面料以羊毛、纱卡、涤卡、磨毛粗斜纱卡、起毛帆布、灯芯绒、毛布皮革等系列。

Huaguan cap companies are the only production in Southwest Sewing hat (fur hat, leather cap, baseball cap, sun hat, embroidered cap), it felt hat child, it felt finished hat, paper hat, fashion hat, straw hats and grass system for handicrafts, embroidery products such as computer professional cap companies, has nearly 50 years of production history.

华冠帽业公司是鲁西南唯一生产缝制帽（裘皮帽、革皮帽、棒球帽、太阳帽、绣花帽）、呢毡礼帽胎、呢毡成品礼帽、纸帽、时尚帽、草编帽及草制工艺品、电脑绣花等产品的制帽专业企业，有近50年的生产历史。

Is the first hat to dress hat with a combination of electronic manufacturer, mainly produces products into three categories: Hats series of products: baseball cap, golf cap, fisherman hat, fashion hat, career cap, the door Children's hat, advertising cap, sports cap and so on.

深圳捷泰电子有限公司深圳捷泰帽业有限公司是国内首家以服饰帽子跟电子相结合的生产厂家，主要生产产品为三大种类：帽子系列产品：棒球帽、高尔夫球帽、渔夫帽、时装帽、职业帽、门童帽、广告帽、运动帽等。

Depending on the geometry of gas-cap and oil column, the physical property and geometric shape of reservoir, and the mobility of edge and bottom water, the multiple oil-driving mechanisms exist in gas-cap reservoirs where there are gas-cap and oil/gas interface, and the recovery factor changes a lot because the oil/gas interface moves during exploitation of gas-cap reservoirs and it is very difficult to adjust and control the oil/gas interface.

气顶油气田因气顶及油气界面的存在，同时因气顶和油环的大小、储层物性、几何形态不同和边底水活跃程度不同，致使气顶油气藏在开采过程中具有多种驱油机理，采收率变化较大，这关键是气顶油气藏在开发过程中存在油气界面的移动问题，而调整和控制油气界面是相当困难。

" I' d like to get some rough idea about music in the baroque ear, please."

请简要介绍一下巴罗克时期的音乐，好吗？

The results showed that the peak latency and pattern of SEPs elicited by electrical needling in LI-l1 and MP were similar. The amplitude of SEPs elicited by electrical needling in LI-l1 was higher than that of MP. There was no obvious SEPs generation when MM was electrical needling.

结果显示，电针刺激曲池穴和其邻近桡侧伸腕长肌运动点诱发性脑电波的波形和波峰时间是类似的，只是穴位的诱发性脑电波波幅较大，而电针刺激非穴位点并没有明显的诱发性脑电位。