查询词典 coil bobbin

In order to study characteristics of the early signal with TEM, the authors formulated self-induction formulae for single coil and multi-turn coils, deduced theoretical expressions for the amplitude of the loop self-induction signal, and gave the induction of single coil and multi-axial coils. The response curve of buried object affected by the coils nod the length of loop's change are also studied.

为研究瞬变电磁早期信号的特性，讨论了多匝线圈与单匝线圈的自感系数的关系，得出线圈自感信号振幅的理论表达式，推导了单匝和多匝回线的电感公式，分析了回线匝数和回线边长的变化对目标体响应曲线的影响。

So we designed a adaptive synchronizing controller based on hereinbefore hardware environment: first a small magnitude reference signal r is outputted to system through the signal card (to ensure that the vibrating system works in a linear state), and this signal is sent to the moving coil of vibrator through the power amplifier, so vibration is produced through electromagnetic induction. Secondly the vibration signal can feedback to the data acquiring card in the servo system through the acceleration sensor on the Vibroseis reactor M〓 and the base-plate M〓, then the computer can get the current vibrating state y〓 of the coil of vibrator according to the feedback information from the data acquiring card, and give a real time comparing between the current state y〓 and the reference output y〓 of the set-in reference model with current reference input being r , then regulates the correlative controlling parameters according to the error e〓=y〓-y〓 till y〓→y〓, finally normal signal sweeping begins with a certain phase fixed. Meanwhile a synchronization signal for seismic signal record is sent to seismograph from synchronization signal outputting component in the Vibroseis system to perform the controlling process of synchronization of sweeping phases.

为此，我们基于以上的硬件环境设计了一个自适应同步控制器：首先通过信号发生卡对系统输出小幅度的参考信号r(从而保证振动系统工作处于线性状态)，信号通过前置放大器、功率放大器等送到激震器动圈，并通过电磁感应产生振动，振动信号通过可控震源激震器反应块M〓和基板M〓上的加速度传感器反馈给伺服系统中的数据采集卡，工控计算机根据采集卡的反馈信息，获取当前激震器动圈的振动状态y〓，并实时地将该状态与内置的参考模型在当前参考输入r下的参考输出y〓进行辨识，再将两者输出误差e〓＝y〓-y〓对系统的有关控制参数进行调整，直至y〓→y〓，最后在经过某一固定的相位后，开始信号的正常扫描过程，与此同时，由可控震源系统的同步信号输出部件向地震仪送出一地震信号记录同步信号，进而完成扫描相位同步控制过程。

Two conductor segments of stator coil are inserted into a pair of slot, which is from first end surface of the stator iron core in six slots sidewise, and stator coil is jointed at end part of segments extended to side of second end surface of the stator iron core.

定子线圈为从定子铁心的第1端面侧向隔开6个切槽的切槽的各对中分别插入2个导体段(15)，并将向定子铁心的第2端侧面延伸的导体段(15)的端部接合而形成。

Objective To analyze the effects of coil size and sample volume on coil signal to noise ratio.

目的 分析线圈大小、样品体积对线圈信噪比的影响。

The voice coil motor components include a permanent magnet and an electric coil attached to the slide bar, powered by the power amplifier.

音圈电机的组成部分包括一个永磁体和一个电动线圈附在滑动条，采用功率放大器。

Even if the webbing belt, is extracted until the torsion coil spring is closely stuck to the adapters the exciting force of the spiral coil spring is not applied to a spool.

以这样的方式，即使安全带被拉长时，盘簧的驱动力也不会作用在卷轴上，直到扭转螺旋弹簧旋紧在承接件和上为止。

Analyzed the structure characteristics of the perfume cover outer shell plastics piece, described the piece's structure and work principle which model a craft and inject a mold, its principle :adopt and certainly be apart from bolt and spring coil and carry on two cents type, use inclined lead a side outside the pillar and take out heart, type the heart crest spare parts, while entering and anticipating adoption incubate the type sprinkle into anticipate a form, while opening a mold, with the ball head pull and anticipate a pole sprinkle and note system and anticipate, then make use of and take out and push plank and release a plastics piece inside a heart,use spring coil and reset first while matching a mold, then carry on willing model a beginning next time.

摘要分析了香水盖外壳塑件的结构特点，叙述了该塑件成型工艺、注射模的结构和工作原理，其原理是：采用定距螺钉和弹簧进行二次分型，用斜导柱外侧抽芯，型芯顶出零件，进料时采用潜伏式浇口进料形式，当开模的时候，用球头拉料杆把浇注系统凝料顶出，然后利用型芯内抽推板推出塑件，合模时用弹簧先复位，然后进行下一次成型开始。

1 Layer of each phase and each parallel connection spur track of stator coil lay at least 6 resistance thermometers, dispose them at the upper, middle and lower of coil axes.

7.1.1定子绕组每相每个并联支路的层间应至少埋设6个，沿绕组轴线上中下布置。

Simply spin it slowly by hand, and start measuring voltage, starting with one coil, and being certain that the voltage increases with each additional coil which is wired in series.

只需旋转，慢慢的手，并开始测量电压，从一个线圈，被确定的电压增加，每增加线圈是有线系列。

The tickler coil is on a wooden coil form and is not too critical.

再生线圈是绕在一个木制蛛网板上的，数据并不很严格。

You can do some assertiveness training.

你可以进行一些自信训练。

We were well on the path to making a rear-wheel-drive global platform," says Mays."

我们正致力于建立一个后轮驱动的平台，"Mays这样说道。"