查询词典 cohesion-tension

Concrete in the tension zone lost its tensile strength, and the steel bars started to work effectively and to resist the entire tensile force.

混凝土在紧张区域丢失了它的抗拉强度，并且铁棍开始运作有效地和抵抗整个张力。

To perform the above tasks a winder is divided into three principal zones:(1) the unwinding zone,(2) the tension and clearing zone, and (3) the winding zone.

为了完成上述工作，络纱机包括三个重要的区间；(1)退绕区，(2)张力及清洁区；(3)卷绕区。

For a doubly reinforced beam, reinforcement area in both the tension and compression zone are calculated

双筋梁在截面受拉区和受压区同时按计算配置受力钢筋。

The position sensors on the rollers provide information related to the amount of strained web material that has been added and subtracted from the web material present in the tension zone.

辊上的位置传感器提供这样的信息，即，该信息与添加到张力区以及从存在于张力区中的卷筒纸材料减去的应变卷筒纸材料的量有关。

To perform the above tasks a winder is divided into three principal zones:(1) the un winding zone,(2) the tension and clearing zone, and (3) the winding zone.

为了完成上述工作，络纱机包括三个重要的区间；(1)退绕区，(2)张力及清洁区；(3)卷绕区。

To perform the above tasks a winder is divided into three principal zones:(1) the unwind ing zone,(2) the tension and clearing zone, and (3) the winding zone.

为了完成上述工作，络纱机包括三个重要的区间；(1)退绕区，(2)张力及清洁区；(3)卷绕区。

A crack in the tension zone of the concrete implies that some slip has occurred between the steel reinforcement and the surrounding concrete.

在混凝土受拉区出现裂缝意味着钢筋与周围的混凝土之间产生了一些滑移。

Stage 3: When the load was increased beyond P1 (greater than 6000 lb, 26.7KN), tensile stresses in concrete at the tension zone increased until they were greater than the modulus of rupture fc, and cracks developed.

阶段3：当装载在P1 (大于6000磅之外被增加了， 26.7KN)，张应力在混凝土在紧张区域增加了，直到他们大于破裂fc的模数，并且被开发的镇压。

Supersaturated hydrogen concentration in tension stress zone but directly promotes vertical crack propagation.

轴向裂纹在MnS和CaS夹杂以及析出相处形核，以氢压为主要的裂纹扩展动力。

This is taken as either of the following, whichever is exceeded first; deflection of L/20 rate of deflection = L2/(9000d) mm/min where L is the clear span of the specimen and d is the distance from the top of the structural section to the bottom of the design tension zone.

下面任意一项无论哪一项先超出限制： L/20 形变 L2/(9000d) mm/min的形变率，这里L是样品的净跨而&d&是设计的张力区域结构型面上下之间的距离。

A carrier gas such as nitrogen is directed through line 20 and valve 22 to connect with line 26 and mix with the gas sample.

如氮气之类的载体通过管线20和阀22引入，与管线26相通，与气体样品混合。

But for the most part, knaves and parasites had the command of his fortune

然而支配他的家产的大多是恶棍和寄生虫。