查询词典 coating material

Han Sen Bangde Beijing Co., Ltd. was established in 1997, is the major domestic production, research and sales thermoset powder coating as one of the enterprises, an international field of powder coating the most advanced production technology and techniques, first-class modern production equipment, complete Complete testing tools and excellent management personnel, the annual capacity of excellent quality powder coating over 5,000 tons.

北京汉森邦德有限公司成立1997年，是国内主要集生产、研究和销售热固性粉末涂料为一体的企业之一，拥有国际粉末涂料领域最先进的生产工艺和技术，一流的现代化生产设备、完整齐备的检测手段和优秀的管理人才，每年可生产品质优异的粉末涂料5000多吨。

Coating thickness of the coating determined using point-3:00 measured the thickness of the coating thickness gauge general, the living

涂装漆膜厚度的测定，用触点式漆膜测厚仪一般测定3点厚度，取其平均值。

The result indicate that: the electrodeposition of zinc on nickel and tungsten substrates involves instantaneous three-dimensional nucleation. The coating is the best when the current density is 4mA/cm2 and the temperature is 80 ℃. The coating by the method of the impulse electrodeposition is better than the direct current electrodeposition. Especially when f is 100Hz, ton/toff is 2/8 and J is 8mA/cm2, the coating is clean and uniformity. The crystal size is nearly 0.3μ m .

结果表明：阴极反应为准可逆反应，锌离子在镍电极和钨电极上形核是三维瞬时形核半球形扩散长大过程，直流电流密度为4mA/cm2，温度为80 ℃时，镀层质量最好；脉冲电沉积得到的镀层要优于直流电沉积得到的镀层，尤其在脉冲宽度为2ms，脉冲间隔为8ms，电流密度为8mA/cm2时，得到的镀层光滑而均匀，颗粒大小接近0.3μm。

The cast coated sheet comprises a substrate and a brushed coating layer comprising a pigment, a functionally effective amount of latex such that a dried unbrushed layer of the coating will not adhere sufficiently to the casting surface to allow the unbrushed layer to be cast, and a functionally effective amount of brushing agent such that damage to the coating layer surface during brushing is minimized.

该铸塑涂布平张纸含有一个基片和一层涂刷过的涂层，该涂层包括涂料，含量为功能有效量的乳胶液，使得该干燥的未刷涂层不与铸塑涂布面充分粘接到足以对该未刷涂层进行铸塑涂布的程度，和含量为功能有效量的涂刷剂，使得在涂刷过程中对该涂层的损伤减到最小。

The test shows that all performance index of LT coating have reached or exceeded GB 18445-2001 standard.Comparisons on waterproofness with overseas typical products of the same kind Penetron 401 coating indicate that the waterproofness of LT coating is not lower than that of Penet...

经测试LT涂料的各项性能指标，均已达到或超过了GB18445—2001标准要求，并与国外具有代表性的同类产品Penetron401涂料进行了防水性能对比，表明LT涂料的防水性能不低于Penetron401产品，完全可以取代同类进口产品。

By diffusion of heavy metal ion into zinc oxide crystal,ACR-1 white antistatic thermal control coating is developed with acrylic resin.The space environment effects on the solar absorbtance of the coating and comparison with silicon white thermal control coating are investigated.

通过在氧化锌晶格中掺入重金属离子，得到具有防静电功能的白色颜料，再以丙烯酸树脂为粘合剂制备出空间飞行器外表面用的 ACR-1防静电白色热控涂层；研究了空间环境效应(包括紫外辐照，电子和质子辐照)对该热控涂层太阳吸收率的影响并与有机硅白色热控涂层进行了比较。

An AlTiN ceramic coating was deposited on the surface of biomedical Ti6Al4V alloy by High Ionic Pulse technology. The properties of biofriction and wear of AlTiN coating in simulated serum lubrication at 37℃ were investigated and compared with that of non-coating Ti6Al4V alloy.

采用高度离子化脉冲工艺在医用钛合金Ti6Al4V表面制备AlTiN涂层；在摩擦磨损试验机上测试了涂层在37℃的模拟人体生理血清液润滑条件下的摩擦磨损性能，并与之和未经涂层的Ti6Al4V合金作比较。

The product offers a perfect solution for the problem of color durableness of mineral coating and makes mineral coating really coexist with nature, really a revolution of coating industry.

改性后的硅酸钾不但具有更为良好的化合性，同时与各种氧化无机色素能良好相容，彻底解决了矿物涂料的色泽问题，使得矿物涂料真正与自然共存，成为涂装行业的一次革命。

To analyze and compare each targets of pre-coating Cu and pre-coating Ni,which are the two pre-coating methods adopted in electrocoating Cu for Cu-cladded steel wire The relative matters needing attention and measures of improvement are put forward,which have important significances for cutting down production cost and improving product qualit

对铜包钢丝在电镀铜过程中采用的两种预镀方法———预镀铜和预镀镍的各项指标进行分析比较，提出相应的注意事项和改进措施，对于降低生产成本，提高产品质量意义甚大。

To analyze and compare each targets of pre-coating Cu and pre-coating Ni,which are the two pre-coating methods adopted in electrocoating Cu for Cu-cladded steel wireThe relative matters needing attention and measures of improvement are put forward,which have important significances for cutting down production cost and improving product qualit

对铜包钢丝在电镀铜过程中采用的两种预镀方法———预镀铜和预镀镍的各项指标进行分析比较，提出相应的注意事项和改进措施，对于降低生产成本，提高产品质量意义甚大。

We are in a good position to meet your requirements.

我们完全可以满足你方的需求。

We are all pervade d with a sense of disaster.

我们普遍有大祸降临的感觉。