查询词典 coated with

The combination of corundum-coated cBN abrasive with vitrified bond is better than that of Ti-coated or un-coated cBN. And the buffer layer from cBN abrasive, corundum coating to bond is perfect because part of corundum coating melts into vitrified bond to build dentation combination.

表面涂覆刚玉和镀覆Ti的cBN磨粒与结合剂的结合效果均比未镀覆的好，但涂覆刚玉比镀覆Ti的效果更好，刚玉涂层以牙形溶入结合剂中使得磨粒、镀层和结合剂三者过渡良好。

The surface appearance and hygroscopicity of ADN after coating were analyzed by SEM and weighing method. Results show that a kind of floccule of PU is formed on the surface of ADN, which makes the hygroscopicity of ADN after coating less than that before coating evidently. When coated ADN is exposed in the atmosphere for 30 days with the RH less than 60%, the hygroscopicity of coated ADN is only 0.136% and does not increase with the increasing of exposure time.

用扫描电镜和称重法分析了包覆后ADN的表面形貌和吸湿性，结果表明，聚氨酯黏合剂在ADN表面形成絮状的包覆膜，使包覆后ADN的吸湿率明显小于包覆前ADN，在相对湿度60%以下，包覆后ADN在空气中暴露30天时吸湿率仅0.136%，吸湿率不随时间增加。

Screen printing is a polymer-coated paper with ice flower in high smoothness of surface covered with a layer of high vacuum of polymer-coated aluminum, is to determine the quality of ice screen printing quality of one of the key factors.

网印冰不攒覆膜纸是在矮平滑量的纸板表背包围了一层矮平华的假不满镀铝膜，覆膜量量是决不退冰不攒网印量量的关头不败不合之一。

I tried my best so many times to make a chocolate coated polvoron but I can't get the technique how to mix the coated chocolate or I say the procedure of the coated chocolate and how to mixed it with the powdered polvoron in a moulder, please answer me immediately because I have been selling polvoron since I resign in my job.

我尝试我最好的，所以很多时候做出的巧克力包衣polvoron ，但我不能得到技术如何组合涂层巧克力或我说的程序包覆巧克力以及如何混合，它与粉状polvoron在moulder ，请我的答案马上，因为我一直在抛售polvoron自从我辞去我的工作。

Meanwhile, the coated surface was hydrophobic with a contact angle of 107.2°since the introduction of methyl groups and methylene groups. Static immersing corrosion test, potentiodynamically polarization curve and electrochemical impedance spectroscopy were conducted to evaluate the film corrosion performances. The results of potentiodynamically polarization curve and EIS in 55wt% LiBr solutions at room temperature in atmospherical pressure indicated that the corrosion current density of BMBSE film coated surface was 4 orders of magnitude smaller than that of bare SUS304 steel, and the impedance was increased by a factor of 10000. Static immersing corrosion test presented that the BMBSE film can significantly increase the corrosion resistance in 55wt%LiBr solution at 180°C compared with stainless steels.

同时由于有机组分甲基和亚甲基的引入，结构均匀致密，并具有一定的疏水性；电化学测试结果表明BMBSE膜的极化阻抗比不锈钢大4个数量级，自腐蚀电流密度也下降低了4个数量级左右，具有良好的耐腐蚀性能；成膜的影响因素优化结果表明BMBSE、EtOH、D.I.water摩尔比为1∶4∶3，热处理温度为200℃时，更有利于制备结构均匀、致密、耐腐蚀性能好的薄膜；静态浸泡腐蚀实验结果说明，在180℃、55%的高温溴化锂溶液中BMBSE膜能起到良好的腐蚀防护作用。

Proximal bone stress transfer has been thought to be less in association with proximally coated stems as compared with extensively coated stems.

近端涂层的股骨柄与广泛涂层的股骨柄相比，近端骨压力传导被认为较小。

In this project, the selection criteria of matrix and reinforcement for obtaining composites with high strength and toughness are determined. The as-cast and aged microstructures of composites reinforced with particles of different strength are observed, and their metallurgical conditions and stabilization mechanisms are analyzed. The aging precipitation behaviors and mechanisms are studied. Some characteristics of nano-materials (micro-distortion areas) are found in 150nm- Al2O3p/Al composites and their formation mechanisms are expatiated. The "flexible" restriction to the deformation of the matrix by low strength AlN particle is observed by in-situ TEM and SEM techniques, and the mechanisms of its resist on cracks propagation and its contribution to composite strength are revealed. The high temperature deformation behaviors of Al2O3p/Al composites are studied. A rare-earth coating is established on sub-micron Al2O3 particles, leading to an improvement in wettability between coated Al2O3 and liquid aluminum and a decrease in infiltration pressure. The strength and ductility of coated particles reinforced composite are also increased. The interfacial characteristics, bonding structures and their formation mechanisms are studied, and the crystal orientation relationships between reinforcement particles and aluminum matrix are investigated. Finally a lighter composite with better balance of strength and damping properties is reinforced with hollow ceramic microballoons of ultra-lower strength.

本项目发现了获得高强度和高韧性复合材料的基体、增强体选择依据；观察了各种强度质点增强复合材料的铸态和时效态微观组织，分析其微观结构形成的金属学条件及稳定性机理，研究了其时效析出规律和时效机制，发现了150nmAl2O3颗粒增强铝基复合材料基体中的纳米材料特征，并解释了其形成机理；利用TEM和SEM动态拉伸技术发现了低强度质点AlN颗粒对变形协调的&柔性强化&机制，揭示了其对裂纹扩展的阻碍作用和对复合材料高强度的贡献；研究了中强度质点的Al2O3颗粒增强铝基复合材料的高温变形行为，并对其进行了稀土界面层设计与制备，改善了颗粒与铝合金之间的界面润湿性，降低了复合材料铸造渗透压力，提高了复合材料的强、韧性；研究了多种复合材料界面结构及形成机理，确定了增强体与基体之间的界面结合机制，分析了复合材料界面处的晶体学位向关系；最后制备了含微孔的中空型陶瓷颗粒增强的特种复合材料，得到了强度和阻尼综合性能较好的轻质复合材料。

The results show that: the tensile strength, flexural strength and flexural modulus increase by about 10.4%, 62.1% and 122.3% respectively when the mass fraction of the aluminum powder increases from 0 to 50%, while elongation at break and impact strength decrease by about 65.0 and 74.4% respectively; the tensile strength, elongation at break and impact strength all increase with decreasing the particle sizes of the aluminum powders.b Nylon-12 coated metal powders for the indirect SLS process were prepared by the dissolution precipitation process. The coated powders have only 1.0 wt% nylon-12, and their SLS green parts have sufficient strength for features as small as 1.0 mm to be built and post-processed and high dimensional accuracy. The green parts were subjected to the post processing processes including binder decomposition and infiltration of epoxy resin, and then the metal/polymer composite parts with relatively high strength and accuracy were formed.At present, micron-scale inorganic fillers have been widely used to reinforce nylon SLS parts.

将该法制备的尼龙12覆膜金属粉末用于以下两个方面：a使用铝粉增强尼龙12的SLS成形件，通过溶剂沉淀法制备尼龙12覆膜铝复合粉末，研究了铝粉含量及粒径对SLS成形件性能的影响，结果表明：铝粉分散均匀，并与基体有良好的界面粘接；当铝粉含量从0增加到50wt％时，成形件的拉伸强度、弯曲强度、弯曲模量分别提高10.4％、62.1％和122.3％，冲击强度和断裂伸长率下降65.0％和74.4％，耐热性及尺寸精度也得到提高；断裂伸长率、冲击强度及拉伸强度均随着铝粉粒径的减小而增大。b使用溶剂沉淀法制备了间接法SLS用尼龙12覆膜金属粉末，该覆膜粉末中聚合物粘接剂的含量仅为1.0 wt％，其SLS初始形坯具有较高的精度以及足够满足后处理要求的强度，最小精细结构的尺寸达1.0 mm。

The domestic accessions exhibited high relatedness of root color within each sub-group. The accessions with red-coated root were nearly put into one sub-group, while the accessions with white and green-coated or white-coated root were put into the other sub-group.

国内种质的分类表现出了与根皮色密切相关的特征，基本上是根皮色为红色的聚为一个亚组，根皮色为白色和绿白色的聚为一个亚组。

Based on the experience with more than 10 years running shell mould casting line and with the application of various resin coated sand s,some technical problems of resin coated sand s for shell mould castings were discussed.

根据壳型生产线十几年运行和各类覆膜砂应用的经验，对壳型铸造用覆膜砂的一些技术问题进行探讨。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了