查询词典 clearance

The current involute spline broach is analyzed,the grinding technology of involute spline broach with side clearance is described,the profile is designed,and profile error is analyzed.

分析了现有渐开线花键拉刀的缺陷，提出带侧刃后角的渐开线花键拉刀的磨削工艺，并进行了齿形设计及齿形误差分析。

Adjustment of the countertop with the seams of the wall: when the benchmark side of the countertop joints with the jointing side, in case the clearance between splash back of the countertop and the wall is larger than 5MM, use the following method to adjust.

台面与墙面缝隙的调整：接驳台面基准边与对接边合拢后，对于非直角墙体，如台面挡水与墙体面缝隙超过5MM，我们可以通过下面的方法调整，将两块台面紧靠墙，将两块台面的后挡水边靠拢在一起，这时两块台面的前端有间隙，就用卷尺测量前端间隙的尺寸，在后挡水处按间隙尺寸做标记，连接前端点和后面的标记划线。

Idlers use stamped bearing house. Using wide clearance bearing and multi-layer labyrinth seal improves service life, reduces rotation resistance and friction coefficient. Cast welding and keyless connection has been used for pulley, Hydraulic coupling and hard surface cone cylinder gear speed reducer for drive unit, angle type structure for head frame, so these improve starting performance, drive efficiency, load capacity and service life, reduce floor area and weight of equipment.

托辊采用了35°槽型前倾结构，辊子为冲压轴承座结构，大游隙轴承和册层迷宫密封，提高了寿命，降低了旋转阻力和摩擦系数，滚筒采用了铸焊结构和无健联接，驱动单元采用了液力耦合器和硬齿面圆锥圆柱齿轮减速机，头架采用角型结构，从而改善了启动性能，传动效率，承载能力和使用寿命，减少了占地面积和设备重量。

In the pump body installed a stator swing span and a swing span rotation shaft, the swing roller bearing on the stator swing span connects with an end of the stator mount, the other end of the stator mount connects with the stator; on the plunger connecting rod sliding boot installed a static pressure balance chamber, the holding rings are arranged on the two sides of the plunger connecting rod sliding boot which has a fit clearance with the holding rings; the rotor rotates the stator simultaneously via the plunger piston; the needle roller bearings are arranged on the two inner circles and fit with the port axle.

在泵体内安置有定子摆架和摆架转轴，位于定子摆架上的摆架滚子轴承与定子托架的一端配合联接，定子托架的另一端与定子相连；柱塞连杆滑靴上设有静压平衡室，柱塞连杆滑靴两侧设有保持环，柱塞连杆滑靴与保持环有一定的配合间隙；转子通过柱塞带动定子同步旋转；在转子内圆两端设有滚针轴承，滚针轴承与配流轴配合。

It is not possible to manufacture a 100%-sealed optical encoder because the bearing-to-shaft assembly will never be perfectly tight. There must be a clearance to allow the bearing to slide over the shaft during assembly of the encoder.

生产制造出一个完全密封的光学编码器是不可能的，因为轴承-传动轴的组装不可能完全密封，必须要有个间隙，在编码器组装的时候让轴承滑动到传动轴上。

Polishing machine coated roll and roll and penetrated the metering rollers, directly affects the product iuster is good or bad, such as coating roll and roll of clearance too large, you can Polish paper and coated rolls off the paper bad contact so that the oil absorption corresponding regarding the reduction of roll coating rollers and penetrated the size determines the amount of finish coating the, should be based on the paper--absorption of strong or weak, adjustment and coated roll roll the size of the gap in order to ensure that products on the light intensity.

上光机的涂布辊与衬辊和计量辊之间的间隙是否合适，直接影响到产品上光亮度的好坏，如涂布辊与衬辊的间隙调得太大，就容易使上光的纸面与涂布辊接触不良，使纸面吸油量相应就减少涂布辊与计量辊之间的间隙大小，则决定着上光油涂布量的大小，所以，应根据纸面吸收性的强弱，调整涂布辊与计量辊间隙的大小，才能确保产品上光的亮度。

According to experiences in final assembly, factory test and performance test, some adjustment methods are summarized for the axial clearance of single-row tapered roller bearing.

根据总装、出厂试验和性能试验的经验，总结出单列圆锥滚子轴承轴向游隙的调整方法。

By setting up force model of rolled stock in cutting area, function relation among clamping force, side clearance of cutting blade and side thrust is given out.

建立了轧件在剪切区的力学模型，给出了压板力、剪刃侧隙与侧推力的函数关系，并提出减小侧推力影响的对策。

By setting up force model of rolled stock in cutting area, function relation among clamp ing force, side clearance of cutting blade and side thrust is given out.

建立了轧件在剪切区的力学模型，给出了压板力、剪刃侧隙与侧推力的函数关系，并提出减小侧推力影响的对策。

It was our Serb's brilliant headed clearance three minutes into stoppage time that ensured the shut-out and the 1-0 win.

在那场比赛的最终，靠着塞尔维亚人在补时3分钟出色的头球解围化解了对方的进攻，我们保住了1比0的胜利。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷