查询词典 clearance size

Melissa: If your size is 0, we have one you may like on a clearance sale.

店员： 如果你穿0号的话，打折的里面有一个您可能会喜欢。

A calculating method to determine the clearance size of the rudder face along the extension direction of the swept-back wing for airplane is presented, which can be used for calculating the clearance size of the rudder face at limiting deflection angle, and point out that several parameters for determining the caearance is essential .

本文针对某型无人机翼面、舵面设计，首先导出了一种确定后掠翼舵面展向缝隙尺寸的计算方法，使用该方法能够定量地计算舵面在极限偏转角下缝隙的尺寸，并指出决定舵面缝隙大小几个主要参数，为舵面缝隙设计提供了可靠依据。

The placket size decides the displacement of the regulation arm when the clearance adjusting beginning.

调整环的开口尺寸确定了拨又开始调整间隙的位移，也是保证机构进行正确工作的关键部分。

3I described two sub-band division method in the frequency domain, and brought forward idea that the energy unitary, and the use one of them to decompose and calculate the entire frequency band. After analysis the results, I could achieve to the band of each prompting and respond, and we used this section energy to determine whether or not unconventionality about the size of valve clearance.

3在频域中描述了子带的两种划分方法，提出了对能量进行归一化的基本思想，并用其中的一种划分方法对整个频带进行了分解计算，经过对计算结果的分析，得到了各个激励响应集中的频带范围，并由此段能量的大小来判断气门间隙有无异常。

The numerical results show that:(1) the throughflow wake is considerably influenced by the tip clearance. The low-kinetic-energy fluid accumulated in the shroud/pressure side of the unshrouded impeller, but in the shroud/suction region for 0.0 tip clearance;(2) there possibly exists an optimum size of the tip-clearance which is not the zero tip clearance to make the flow loss minimized.

研究结果表明，(1)NASA低速大尺度离心压缩机半开式叶轮的低速尾迹区在压力面与轮盖的角区，而相应的闭式叶轮的低速尾迹区聚集在轮盖的中心位置；(2)数值实验表明，叶顶间隙并非越小越好，可能存在一个最优间隙，使得叶轮流动损失最小。

The simulation model is built with Simulink, and the influence of the clearance size on the dynamic stability of the mechanism is analyzed. The feasibility of two algorithms in Simulink for solving this simulation model is discussed. The results indicate that the algorithm ode23tb can ensure the solution stability better.

利用Simulink构建系统的仿真模型，分析了运动副间隙大小对机构运动稳定性的影响，探讨了Simulink仿真算法求解此仿真模型的有效性；结果证明，利用Simulink提供的ode23tb算法能更好地保证其动力学求解的稳定性。

Then the numerical simulation is developed with the above dynamic model. The effects of the clearance on the dynamic characteristics are studied in detail. The influence of factors such as clearance size, driving speed, stiffness, coefficient of viscous damping of contact surface, and the gravity are discussed and the quantitative results are given.

利用本文建立的动力学模型对含间隙三球销移动副的曲柄滑块机构进行了动力学数值仿真，研究了运动副间隙对机构的运动和受力状况的影响，考察了间隙大小、曲柄转速、接触刚度、阻尼、外力矩等对机构动态特性的影响规律，给出了定量结果。

Based upon SIMPLEC algorithm of CFD analysis, air film flow in the oil-free air bearing is simulated to illustrate its working principle, as well as performance's influence from air compressibility, shaft eccentricity ratio, clearance size and rotating speed.

基于计算流体动力学中的SIMPLEC算法，从流动模拟分析的角度对动压气膜轴承的工作机理，包括气体可压缩性，轴承间隙大小，轴颈偏心率及轴承运行线速度的作用等作了分析。

Over a special range of parameters, the chaotic feature of the system with clearance joint is shown to exist by time domain curve, frequency domain curve or Poincare map and so on. Moreover the kinds of routes to chaos are found as the clearance size or crank speed change.

用多种方法证明了此类机构满足一定条件时存在混沌运动；并以机构运行时间、间隙大小、曲柄转速等作为控制参数，分析了机构周期运动和混沌运动之间的转化路径。

Polishing machine coated roll and roll and penetrated the metering rollers, directly affects the product iuster is good or bad, such as coating roll and roll of clearance too large, you can Polish paper and coated rolls off the paper bad contact so that the oil absorption corresponding regarding the reduction of roll coating rollers and penetrated the size determines the amount of finish coating the, should be based on the paper--absorption of strong or weak, adjustment and coated roll roll the size of the gap in order to ensure that products on the light intensity.

上光机的涂布辊与衬辊和计量辊之间的间隙是否合适，直接影响到产品上光亮度的好坏，如涂布辊与衬辊的间隙调得太大，就容易使上光的纸面与涂布辊接触不良，使纸面吸油量相应就减少涂布辊与计量辊之间的间隙大小，则决定着上光油涂布量的大小，所以，应根据纸面吸收性的强弱，调整涂布辊与计量辊间隙的大小，才能确保产品上光的亮度。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷