查询词典 clearance angle

The wear on the flank face of a tool resulted in a loss of relief angle on the clearance face.

磨损的侧翼面对一个工具造成的损失救济角度清除脸上。

This paper describes the test results of the effects of the angle and clearance of fixed guide blade on the performances of mixed flow pump.

对混流泵固定导叶安放角及叶轮轮缘与泵体前盖间隙变化对泵性能影响的试验结果作了介绍。

The relationship of spring back angle with bending clearance and die shoulder radius in the U-shaped bending of Aluminum alloy sheet was investigated.

主要研究了铝合金板材 U形弯曲回弹角与弯曲间隙、凹模入口圆弧半径之间的关系，分析了不同厚度的板材弯曲回弹角的差异。

The theoretical formulae of the knife rake angle and shearing clearance etc have been deduced by establishing the theoretical model of shearing process, and it provides the theoretical foundation for shearing design.

作者通过建立剪切过程的理论模型，导出了刀刃倾角、剪切间隙等理论表达式。它为剪切机的设计提供了理论基础。

Using the analytical method, this paper presents the formulas for the relation of the inner fleet angle and clearance between wound-on coils of mine hoist in func-tion of drum and rope diameters.

本文用解析法求出了以绞筒直径、钢丝绳直径为函数的矿井提升设备绳弦内偏角和缠绳间隙关系的表达式，并按此绘制了供实际应用的曲线图。

Chatter ; nonlinearity ; rake angle ; clearance ; on-line control

颤振；非线性；前角；后角；在线控制

The nozzle layout in terms of bit cutting teeth's position distribution,clearance and the jet angle are analyzed with the numerical simulation for the 3-D flow field of PDC bits,with regard...

NET为工具对Phoenics软件进行二次开发，建立专用平台，对不同工况条件下的PDC钻头进行数值模拟。

Based on finite element method,stiffness characteristics were investigated under different whirling angle, pedestal parameters ,and fit clearance,to present guidance for design of elastic ring.

本文针对两种弹性环刚度的计算方法——解析法和有限元法进行了对比，分析了各自的适用条件，并基于有限元法分析了涡动角、凸台参数和配合间隙对弹性环刚度的影响，为弹性环的结构设计提供了参考。

In order to keep rational radial clearance and decrease the part fit gap, the combined method of positive equidistance plus positive move distance is proposed to modify the cycloid disk tooth profile, so that the processing tooth profile and the rotate angle reparing shape are almost consisitent, and the transmission precision is enhanced.

为了保证合理的径向间隙，减少零件配合的侧隙，通过对摆线轮齿廓采用正等距加正移距的组合方式修形，以保证加工齿廓与转角修形齿廓基本吻合，提高传动精度。

To burning the heavy oil in diesel locomotive, the injection unit must be adjusted, such as the clearance of piston, the spring character of unilateralism valve, the needle valve lift of injector and so on. At the same time, the parameter of injection, such as the injection advace angle, the injection time, should be adjusted according to the actual instance.

针对燃用重柴油的实际，需对柴油机喷射元件，如：喷油泵柱塞偶件间隙、出油阀弹簧刚度、喷油器针阀升程、及喷射参数，如：喷油提前角、喷油定时等均需作出调整，本文论述了具体的调整方法和依据。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。